Soundstream PICASSO COMPONENT SYSTEM Bedienungsanleitung

PICASSO COMPONENT SYSTEM

OWNERS MANUAL/INSTALL GUIDE

www.SOUNDSTREAM.com

Keep in a safe and dry place for future reference.

Model Number of your woofer

Serial Number

Place of purchase

Notes

Soundstream Technologies

1550 S. Maple Ave.

Montebello, CA 90640 USA

PH: 323.724.4600 FX: 323.722.8125

www.soundstream.com

Congratulations on your purchase of Soundstream’s Picasso component

speaker system. The Picasso component system represents Soundstream’s

design approach to creating musical reproduction with the richness and

clarity while maintaining cost effectiveness. Only the best materials and

production techniques were used to create an exceptional line of

component system speakers. We hope you will enjoy your Picasso

components for many years to come.

Features:

•Stamped steel basket with brushed finish

•Woven glass fiber spruce pulp laminate cone

•NBR rubber surround

•Precision machined and matched motor assembly

•Custom embossed protective magnet boot

•1” Copper voice coil on aluminum former with reinforced neck joint

•1” Teflon silk dome tweeter with resin coating

•DC tweeter protection circuit

•12dB low pass with presence switch

•18dB high pass with 3-way sensitivity switch

Tweeter Installation

Mounting hardware contained in the packaging will allow a surface or flush

mount installation. The tweeter should be mounted on the same plane and

within 6 inches of the mid-bass driver to avoid any phase shift. Also, as the

frequencies that the tweeter reproduces are very directional, avoid placing

the tweeter in a position that will be obstructed either by objects in the vehicle

or by passengers. As with the mid-bass driver, if a factory tweeter location is

available, it is recommended that it be used. If it is necessary to cut a hole to

mount the tweeter, then be careful to find a location that will have enough

depth and will not interfere with any moving parts in the vehicle.

Flush Mounting: When flush mounting the tweeter, it will be necessary to use

the tweeter cup, rear wing bracket. Mount the rear wing bracket to the

mounting cup with the supplied screw, insert the tweeter into the cup and

secure with the same screw used to mount the wing bracket. Push the tweeter

assembly into the rear of the vehicle’s tweeter opening and fasten assembly

to the opening by twisting on the flush mount ring from the front.

Impedance 4 ohms

Freq.Response 50Hz - 20KHz

Sensitivity 89dB

Power Watts (Rms/Peak) 50Watts/100Watts

Specifications

Dimensions

Mid-bass Installation

•Determine the mounting location. Factory speaker locations are

recommended for ease of installation. When installing in the factory

speaker locations, make sure that there is enough depth to

accommodate the replacement speaker.

•If an alternate locations is used, measurements should be carefully

taken before any cutting is done to insure that there is enough depth

and to make sure that the speaker will not interfere with any moving

parts in the vehicle (i.e. window gears/braces, hood/trunk cables, etc.).

Once the mounting location is decided upon, the grill-mounting ring

can be used as a template to mark the hole and screw locations. If the

panel that the speaker is to be mounted to can be removed, then it is

recommended that the panel be removed before cutting the speaker

hole. Once the hole is cut to fit the speaker, replace the panel. If there

is any metal obstruction the installation of the speaker, with top panel in

place, mark the metal that needs to be removed and then remove it

with tin snips or a saw.

•The wiring that is used should be at least 18 gauge to avoid possible

signal loss. High quality crimp style connectors should be used to

connect the wires to the speaker. Soldering wires directly to the speaker

will void the warranty. If new wiring is necessary, make sure the route

the wires under factory moldings to make the installation as neat as

possible. In addition, make sure that the new wiring is clear of any screw

or clip holes so that it will not be pinched or shorted to metal after

factory panels and screws are replaced.

Crossover Installation

1. The crossover should be mounted in a dry, moisture free location. Never

install the crossover in the door where it can be damaged by water and

moisture. The crossover can be installed in the door panel as long as there

is an undamaged vapor barrier.

2. There are three sets of connections on the crossover. The Input terminals

should be connected to the source of the signal (radio or amplifier). The

woofer terminals should be connected to the midbass driver. The tweeter

terminals should be connected to the tweeter. The tweeter volume can be

set at -3dB, 0dB and +3dB. Ensure that the negative polarity wire of the

tweeter is the one used for setting the tweeter volume level. Make sure

that the polarity on all connections is correct.

L1 L2

C2 C3

R1 R2 R3 R4

+3dB0dB -3dB

TW+ WF- WF+

PUT-

+IN

Inhaltsverzeichnis

Andere Soundstream Lautsprechersystem Handbücher

Soundstream

Soundstream EXC.4 Bedienungsanleitung

Soundstream

Soundstream Exact Exact 5.3 Bedienungsanleitung

Soundstream

Soundstream Exact 6.2 Bedienungsanleitung

Soundstream

Soundstream Class-D & A/B Bi-Amped Pro audio Speaker... Bedienungsanleitung

Soundstream

Soundstream Exact Exact 6.3 Bedienungsanleitung

Soundstream

Soundstream Exact Exact 4.2 Bedienungsanleitung

Soundstream

Soundstream SPL 60 Bedienungsanleitung

Soundstream

Soundstream STL65.C Bedienungsanleitung

Soundstream

Soundstream Exact Exact 4.3 Bedienungsanleitung

Soundstream

Soundstream RF-60C Bedienungsanleitung

Soundstream

Soundstream SPL-50 Bedienungsanleitung

Soundstream

Soundstream 5.2 Bedienungsanleitung

Soundstream

Soundstream SPL40 Bedienungsanleitung

Beliebte Lautsprechersystem Handbücher anderer Marken

JVC

JVC CA-MXK5R Bedienungsanleitung

LG NB4532B Bedienungsanleitung

JVC

JVC CA-FSH100 Bedienungsanleitung

5Core

5Core Pro Series Bedienungsanleitung

EAW

EAW MQV1394e Bedienungsanleitung

Lynx

Lynx GXR-LA10A Bedienungsanleitung

iLive

iLive ITB066B Bedienungsanleitung

RDX

RDX QuickStation 4 Bedienungsanleitung

Electro-Voice

Electro-Voice S-122 Bedienungsanleitung

Sven

Sven SPS-619 GOLD Bedienungsanleitung

Pioneer

Pioneer CS-7070 Bedienungsanleitung

EAW

EAW UB82e Bedienungsanleitung

Sondpex

Sondpex Active Speaker System and Digital Music... Bedienungsanleitung

JVC

JVC NX-PN7 Bedienungsanleitung

Yamaha

Yamaha NX-A01 - Speaker Sys Bedienungsanleitung

SE Audiotechnik

SE Audiotechnik I-LINE Bedienungsanleitung

Gemini

Gemini WRX-843 Series Bedienungsanleitung

TCL

TCL 6100 Series Bedienungsanleitung