Southern Enterprises FA532300TX Bedienungsanleitung

ITEM NO. FA532300TX

ELECTRIC FIREBOX INSERT

OPERATION MANUAL

For assistance with assembly, contact:

Southern Enterprises Inc.

Customer Service 1-800-633-5096

[email protected]

www.seidal.com

Electric Firebox Insert

User’s Operating Manual

Consumer safety information:

Please read this manual before installing and operating this appliance.

WARNING!!!

If the information in this manual is not followed correctly, an electric shock or fire may result in property damage, personal

injury, or loss of life.

Do not store or use gasoline or other flammable vapors or liquids near this appliance.

Safety Feature:

This unit has an internal thermal overload protector, whenever a temperature is reached

that may cause overheating, the heater will automatically shut off. Operation can only

resume when the unit is reset. (See instructions below)

To Reset Heater:

Unplug the heater and wait 10 minutes for the unit to cool down. After 10 minutes, plug

the heater in again and follow the operating instructions described in this manual. Please

unplug heater and contact customer service if problem persists.

Important Operating and Safety Instructions:

CAUTION:

Keep draperies, electrical cords and other furnishings at least 3 feet from the front, sides, and rear of heater.

WARNING:

Risk of fire, keep combustible material away from the front of the electrical fireplace.

Service should only be performed while the electrical fireplace is disconnected from power supply.

Important Operating and Safety Information:

When using electrical appliances, the following basic precautions should always be followed to reduce the risk of fire,

electric shock, and injury.

•Read all instructions before using this heater.

•Only use this heater as described in this manual. Any other use is not recommended by the manufacturer and

may cause fire, electric shock, or injury.

•Before connecting the appliance to the electric source, check that the current and power match those given on the

ratings plate.

•This heater is for use with a 120 Volt electrical outlet. The cord has a three-prong grounded plug, which must be

used in a properly grounded three-prong outlet.

•Avoid the use of an extension cord to avoid risks of overheating and of fire. If you must use an extension cord it

needs to be a grounded No. 16 AWG minimum size and rated for no less than 1875 watts.

•Do not run the cord under carpet. Do not cover cord with throw rug, runner, or similar items. Cord should be

placed away from traffic areas to prevent tripping hazard.

•Never use the cord to pull the appliance.

•Never leave the appliance unattended while it is in use.

•Turn controls to “off” before removing plug from outlet.

•Always unplug heater when not in use.

•Do not use outdoors.

•Only use heater on even and stable surface to prevent the appliance from tipping over.

•To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, such as a

bed, where openings may be blocked.

•Do not use in rooms in which highly flammable materials such as gas, paints, gasoline, solvents, etc. are stored.

•Keep minimum distance of 3 feet between the heater and curtains or other flammable materials.

•Do not place the appliance or the plug in water or any other liquid. Should the appliance accidentally fall into water,

unplug the appliance immediately and have it checked by a qualified person before using it again.

•Do not use the appliance with wet hands, on a damp floor, or when the appliance itself is wet.

•Do not use the appliance if the glass is damaged.

•Do not operate any heater with a damaged cord or plug, after any heater malfunctions, or after heater has been

dropped or damaged.

•The warm air vent becomes very hot during operation—do not touch. During operation, only touch the appliance’s

switches and handles.

•The appliance should not be moved when hot. Never touch the hot parts with your bare skin.

•Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric

shock, fire, or damage to the heater.

•Please turn off the unit manually when leaving/not in use for extended period.

•Please turn off the unit manually when the power goes out.

•Please BEWARE that the plug may become hot.

•SAVE THESE INSTRUCTIONS

Maintenance:

1: Cleaning your fireplace

2: Cleaning the front glass

WARNING:

Before cleaning the exterior of the appliance, disconnect the unit from the power supply. Clean unit

only after it is cool to the touch. You may clean exterior of unit with a soft, damp, lint-free cloth.

The front glass panel may become dirty or dusty. Dust can be removed by lightly rubbing the glass surface with a

clean, lint-free cloth or paper towel. To remove fingerprints or other marks, use a soft, damp, lint-free cloth with a

household glass cleaner.

Helpful Advice For Installing Firebox Into Mantel:

1. These instructions are provided in an easy to follow format. Simply follow the instructions to properly install unit.

2. Please retain all packaging until you have checked that there is no damage and your unit is working properly.

3. Small parts should be kept away from young children.

4. The area around the unit should be kept free of animal hair, lint, and other extraneous material that may be drawn into

the workings of the appliance and could affect its performance.

Positioning/Locating Your Electric Fireplace:

When choosing a location for your new fireplace, ensure that the general instructions are properly followed. For best

result, install the fireplace out of direct sunlight.

Installation Instructions:

Once the location has been prepared, the fireplace insert can be installed.

1. Make sure the unit is turned off (refer to the operating instructions).

2. Place the fireplace insert on the floor, directly behind your mantle. Make sure the backs of both the mantle and the

fireplace are facing you.

3. It is advisable to have 2 people place the fireplace insert into the mantle, as it is heavy. Gently slide it into the opening

in the mantle until the flange is flush against the inside of the fireplace. Make sure the insert is centered left and right in

the opening. Be careful when placing and adjusting the insert, as the bottom of the insert could scratch the finish of the

wood base/hearth of your fireplace.

4. Attach the mounting brackets (found in the fireplace mantel box) with the supplied screws using a Phillips head

screwdriver. DO NOT OVER TIGHTEN.

5. With the help of an assistant, carefully lift completed unit and place it with the front facing out in the final location you

have chosen for your fireplace.

Operating Instructions:

Control Panel on the Front of Unit Main Display

1. On/Off Main power button

2. On/Off Heater button

3. Adjustable Flame Brightness

4. Adjustable Log Brightness

5. Adjustable Timer

Control panel Introduction:

(1)Power (2)Heater (3)Flame (4)Log (5)Timer

(1) Power:

A. Press to switch the unit ON/OFF.

B. The unit will turn on to its default factory settings.

(2)Heater: Main display will show your room’s temperature when the unit is turned on and when making any adjustments

to heater, flame, log, or timer.

A. Automatic Mode: Press the heater button (2) to adjust the temperature rating from 62°F-82°F (17°C-27°C). Every

adjustment changes the temperature by 1°F (1°C). The heater will turn on when the temperature is set higher than the

room’s temperature and will automatically turn off when the room has reached the desired temperature.

B. Manual Mode: Press the heater button (2) until the unit displays “ON”. The heater will only turn off by pressing the

heater button one more time, then display will go blank.

C. To change from Fahrenheit to Celsius: Hold the heater button for approximately 5 seconds, the temperature readout

will switch directly from °F to °C and vice versa.

Note: Due to the unit’s infrared feature, the blower will continue to run for approximately 3 minutes to cool the

internal components after the heater function is turned off. This may result in the blower running for

approximately 3 minutes even after the unit has been completely turned off.

(3) Flame:

This button adjusts the flame brightness levels: F5 – F4 – F3 –F2 – F1 – F0

(F5 being the brightest and F0 off)

(4) Log:

This button adjusts the log brightness levels: L5 - L4 - L3 - L2 - L1 – L0

(L5 being the brightest and L0 off)

Note: The log will “glow” even when set to F0 due to the flame’s light if the flame light is on. Switch flame lights

to F0 to only leave log lights on. To shut all lights off, make sure heater settings are off and switch flames and

logs to F0.

(5) Timer:

This allows you to control the duration of the heater function. Press the heater button until display reads “ON”, then, press

the timer button until you have reached the desired duration time.

Levels: 30 min- 40min- 50min- 1H- 2H- 3H- 4H- 5H- 6H- 7H- 8H- 9H- OFF

Safety Features:

A. Lights can’t be shut off completely if heater settings are on. Flame effect light can be turned off but the log light will

remain.

B. The unit is equipped with a child lock feature. To activate child lock, press and hold power button until log lights

flash. The buttons will be unresponsive and the heater will shut off once the child lock feature is activated. To

return to normal settings, press and hold the power button until log lights flash.

Your electric fireplace is equipped with a “beep” which will sound when turning the unit on, off, or

changing settings with the remote control. To TURN OFF the “beep” sound, hold the

TIMER button down for approximately 5 seconds. To turn the “beep” sound back ON, hold the TIMER

button down for approximately 5 seconds.

ELECTRICAL CONNECTION:

A 12.5 AMP, 120 Volts, 60 Hz circuit with a properly grounded outlet is required. It’s recommended that the fireplace

be on a dedicated circuit, as other appliances on the same circuit may cause the circuit breaker to trip or blow the fuse

when the heater is in operation.

REMOTE CONTROL OPERATING PROCEDURES

(1)Power:

Press to turn the unit ON/OFF

(2) Heater:

Press to turn the heater ON/OFF. Adjust the temperature rating as follows: 62°F -- 82 °F (17 °C --- 27 °C) Note: ℉for the

default units.

: raise the temperature rating,

: lower the temperature rating.

(3) FLAME

Press to adjust the level of brightness of the flame: F5- F4- F3- F2- F1- OFF. (F5 being the brightest and F1 the dimmest)

: raise the level of flame brightness,

: lower the level of flame brightness.

(4) LOG

Press to adjust the level of brightness of the log: L5- L4- L3- L2- L1- OFF. (L5 being the brightest and L1 the dimmest)

: raise the level of log brightness,

: lower the level of log brightness.

(5)Timer

Press to adjust the duration of the heater: 30 min- 1H- 2H- 3H- 4H- 5H- 6H- 7H- 8H- 9H- OFF

(6) DOWN LIGHT

Turn the down light ON and OFF.

Note: Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-Zinc) or rechargeable(nickel-cadium)batteries.

ELECTRICAL SPECIFICATIONS

Voltage:

120VAC, 60 Hz

Amps:

12.5Amps

Watts:

1500 Watts

Lighting:

LED

TROUBLESHOOTING

Problem

Cause

Solution

Heater doesn't turn on with the

power switch.

Main power supply switch is off.

Turn on the main power supply

switch.

Circuit breaker has tripped.

Too many appliances on this

circuit. Be sure that the electrical

supply for this unit is an individual

circuit.

Heater is unplugged from wall

outlet.

Plug the cord into an outlet.

Power cord or power plug are

damaged.

Contact SEI customer service.

Power outlet for power plug prong

is loose.

Check the power outlet and replace

with a new one.

Loose wiring.

Contact SEI customer service.

Heater power switch is off.

Turn on the heater power switch.

Heater system is overheated.

Maybe the heater is covered, or air

inlet or air outlet is blocked, remove

the covering or the blockage and

turn off the power switch and

unplug it. Wait ten minutes, plug it

back in, then turn the heater on

again.

There is an odor coming from the

heater.

The heater may emit a slight,

harmless odor when first used. This

is a normal condition caused by

initial heating of the internal parts,

and will not occur again.

Problem

Cause

Solution

Heater is on but no flame or low

flame intensity.

Flame adjusting knob is at low

setting.

Turn the knob to maximum setting.

Loose wiring at the wall power

outlet.

Contact a qualified electrician.

Flames are frozen.

Loose wiring at the wall power

outlet.

Check all wiring for loose

connections. Contact a qualified

electrician.

Flame element is not attached to

the motor.

Contact SEI customer service.

Rotation motor is defective.

Contact SEI customer service.

Excessive noise in the lower

portion of the heater.

Flame element isn't seated

properly.

Contact SEI customer service.

Motor is defective.

Contact SEI customer service.

"HEATER POWER" switch has been

flipped in the on position, but there

is no airflow.

The air inlet or air outlet is

completely blocked.

Move the unit and make sure to

leave adequate space around it.

Remove the blockage on or in front

of the air outlet.

The heater system is over heated,

the temperature limit thermostat is

cut off.

Check the air inlet and outlet. Turn

off the power switch and unplug it.

Wait ten minutes, then plug it back

in and turn the heater on again.

Fan Motor is defective.

Contact SEI customer service.

Fan blower is balanced badly.

Contact SEI customer service.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or breakdown, grounding provides a path

of least resistance for electric current to reduce the risk of electric shock. This product

Is equipped with a cord having an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded

in accordance with all local codes and ordinances.

This heater is for use on 120 volts circuit and has a

grounded plug that looks like the one illustrated on

Figure 1.(A) See Figure 1 for grounding instruction. An

adapter as shown as C is available for connecting

three-blade grounding type plugs to two-slot

receptacles (B). The green grounding lug extending

from the adapter must be connected to a

permanent ground such as a properly grounded

outlet box. The adapter should not be used if a

three-slot grounded receptacle is available.

Improper connection of the equipment-grounding conductor can result in a

risk of electric shock. Check with qualified electrician or serviceman if you are in doubt as to

whether the product is properly grounded. Do not modify the plug provided with the product – If

it will not fit the outlet, have a proper outlet installed by qualified electrician.

Figure 1

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio or television reception. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received,

Including interference that may cause undesired operation.

Modifications not approved by the party responsible for

compliance could void user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Inhaltsverzeichnis

Andere Southern Enterprises Kamin im Innenbereich Handbücher

Southern Enterprises

Southern Enterprises FA1126959 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1080759 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1137456 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA9278 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1153859 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1009259 Bedienungsanleitung

Southern Enterprises

Southern Enterprises Lantara FA1140456 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA9275 Bedienungsanleitung

Southern Enterprises

Southern Enterprises Elkmont FA928100TX Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1136956 Bedienungsanleitung

Southern Enterprises

Southern Enterprises Austindale FA1137556 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1137256 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA927500TX Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA9333 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA939800TX Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1080759 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA927800TX-ESPRESSO Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1154656 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1154859 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA1062859 Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA927800TX Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA9316R0TX-Brown Mahogany Bedienungsanleitung

Southern Enterprises

Southern Enterprises FA932100TX Installationsanleitung

Southern Enterprises

Southern Enterprises FA1009359 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch