Sovol SV01 Handbuch
SV01
Guide Book
To make Top-quality 3d printer
V.2.0En
Select the correct input voltage to mach your local mains (220V or 110V).
Not use the printer any way other than described here in order to avoid personal injury or property damage.
Do not place the printer near any heat source or ammable or explosive objects. We suggest placing it in a well-ventilated,
low-dust enviroment.
Do not expose the printer to violent vibration or any unstable enviroment, as this may cause poor print quality.
Before using experimental or exotic laments, we suggest using standard laments such as ABS or PLA to calibrate and test
the machine.
Do not use other power cable except the one supplied. Always use a grounded three-prong power outlet.
Do not touch the nozzle or printing surface durint operation as they may be hot. Keep hands away from machine while in
use to avoid burns or personal injury.
Do not wear gloves or loose clothing when operate the printer. Such cloths may become tangled in the printer moving parts
leading to burns. Possible bodily injury, or printer damage.
When cleaning debris from the printer hotend, always use the provided tools. Do not touch the nozzle directly when heated.
This can cause personal injury.
Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered
printing plastics or any othe material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the
print surface before every print for consistent results.
Children under 10 years of age should not use the printer without supervision.
1
2
3
4
5
6
7
8
9
10
11
Notes
Preface
This Guide is designed for Sovol users to start their
printing journey.
We still recommend that please read this guide even if
you are familiar with the 3d Printing technology, as
there are lots of important information about the sovol
for you get a better 3d experience.
In this guide there are links to video tutorials and
downloads, use the Qr-codes or Click to access.
Additional resources and information:
(1) Quick start Guide
Quick start user guide or video found on the Micro Sd
card.
(2) Ofcial website: www.sovol3d.com
Find out all the latest news which contains the
up-to-date information concerning software, rmware,
device maintenance and so on.
3) Sovol Ofcial User Group on Facebook.
Be a part of the Sovol community sharing your projects
and helping each other.
Index
Index
02 Printer Parts
03 Box Contens
04 Assembly
08 Cable Connection
09 Quality Adjustments
10 Screen Information
11 Bed Leveling
12 Loading Filament
13 Software Installation
14 Preparing to Print
15 Conection Diagram
16 BLTouch Installation
17 After-Sales Service
01
02
1
2
3
4
5 6
7
8
9
10
11
12
13
14
15
16
Printer Parts
1. X Axis Motor
2. Main control box
3. Hot bed
4. TF Card and Usb
5. Display screen
6. Button knob
7. Nozzle kit
8. Extrusion kit
9. Filament holder
10. Filament sensor
11 Couplers
12. Y Axis Motor
13. Foot pad
14. Z Axis Motors
15. Power switch
16. Leveling nut
1
2
3
4
5
6
7
8
9
10
11
12 13 14
Box Contens
03
1. Gantry
2. Base with hot bed
3. Filament holder
4. Display Screen
5. Usb cable
6. Z Axis switch limit plate
7. Screws, T-Nuts and extra nozzle
8. Micro SD card and Reader
9. Power cable
10. Filament (200gr.)
11 Pliers
12. Spatula
13. Tool set
14. Nozzle cleaner (0.4mm)
Assembly Steps 1-2
4
M5x25 + WASHERS (4 Units)
Front
A
1
Remove the parts from the box.
Note that the base and gantry are
connected at the factory. If possible,
perform this operation with the help
of another. Remove any tape and
padding from the parts. Inspect the
parts to make sure they were not
damaged in shipment.
Install the gantry (A) to the base (B).
a) On the gantry frame make sure
the nozzle assembly is in to the
front, and the long vertical leads
screws is in to the back.
b) On the base frame, make sure
the black belt tensioner is on the
front, and the stepper motor is on
the back.
Use the M5x25 screws (4) with their
washers. Lift the base frame. Install
the screws through the base frame
into the threaded holes in the gantry
frame. Tighten with an Hex key
(Allen). Do not exceed tightening to
avoid deformations in the frame.
1
2
2
B
04
Front
4mm
33Install the lament spool holder.
Secured in the screw hole of the
lament holder with M4x8 (2)
and M4 T-Nut (2). Loosen the
T-nuts by hand and turn them so
they will t inside the grooves on
the frames.
You want the nuts to be loose so
that when you tighten the bolts,
the nut will rotate 90° and grab
onto the inside of the groove.
Tighten with an Hex key (Allen).
Assembly - Step 3
05
M4x8 + T-NUTS (2 Units)
2.4mm
4
5
4Install the lament sensor.
The plate with the lament sensor is
installed in the upper rear part of the
frame. The correct direction is indicated by
an arrow on the sensor housing. Fixing to
the frame is similar to the method used
previously. Use the M4x8 (2) screws with
M4 T-Nut (2). Loosen the T-nuts by hand,
when you tighten the screws, the nut will
rotate 90° and grab onto the inside of the
groove.
Install the Lcd screen.
The screen is mounted on the right front of
the base frame. Use the M5x20 (2) screws
provided with their washers. Install the
screws throught the Screen plate into the
threaded holes in the bottom frame.
In another step, we will explain how to
make screen connections
5
06
M5x20 + WASHERS
(2 Units)
M4x8 + T-NUTS (2 Units)
Assembly - Steps 4-5
2.4mm
4mm
07
Assembly - Step 6
6
6Install the Z limit switch
This device sets the starting height of the
Z axis, which is responsible for the up and
down movement of the print head.
It is placed next to the left Z stepper motor
and xed to the edge of the vertical frame
using the included T-nuts.
Loosen the T-nuts, place a card or slightly
thick paper in the bottom frame and rest
the sensor plate on the top. This will
provide the correct minimum height,
slightly above the horizontal prole. Tighten
the screws and connect the 2-wire
connector labeled "Z".
M4x10 + T-NUTS (2 Units)
3mm
X
EXP1
EXP2
Z
E
4-WIRE CONNECTORS
X Y Z
2-WIRE CONNECTORS
ZZ EYX
FD
Y
Z
ZY
X
Make connections
The cables are provided with
labels, observe them and the type
of connector for proper
identication.
Make the connections being
careful not to bend the connector
pins.
The display board has three
identied inputs. Connect the
Exp1 and Exp2 cables in their
corresponding place leaving the
Exp3 input empty..
Cable Connection
08
IMPORTANT
Do not forget to place the voltage selector in the position
corresponding to your local mains (220V or 110V).
Use a grounded electrical outlet.
Inhaltsverzeichnis
Andere Sovol 3D-Drucker Handbücher
