SOYAL
ACCESS CONTROL SYSTEM
®AR-821EF-V5 / AR-821EV-V5
V120508
H. Arming Password
J. Duress Code
K. Terminal Port
I. Arming Delay Time
Access programming mode → Parameters[1] → Arming PWD → Input 4-digit PIN (0001~9999; Default: 1234) → Succeeded
Or via 701Server and set it on AR-829E screen
38
Or via 701Server to set it on AR-829E-V5 screen
※Duress Code is only available in networking mode. It will substitute a personal pin code and send the message of Duress to computer as a
warning signal.
Access programming mode → Parameters[2] → Duress Code → 4 sets (select one) → Input 4-digit PIN (0001~9999) → Succeeded
4 7
Access programming mode → Tools → Terminal Port → 0:Lift ; 1:Host ; 2:LED ; 3:PRN (default value:1) → Baud Selection
(default value:9600) → Succeeded
5 4
L. Setting up the alarm / arming
Conditions:
1. Arming enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: When power is off and then on, reader on arming before power off.
Enable/Disable the arming status:
Standby Mode
Access Programming mode
Card only Card or PIN Card and PIN
Open the door
Present the tag to reader → Input
4 digits arming PWD →
Input user address → Input 4
digits individual PWD → →
Input 4 digits arming PWD →
Present the tag to reader → Input
4 digits individual PWD → →
Input 4 digits arming PWD →
Enable: Access programming mode → Quit & Arming
7Disable: Access programming mode → Quit
6
No open the door
→ Input 4 digits arming PWD
→ Present the tag to reader
Access programming mode → Parameters[1] → ArmingDelayTm → Enter armed sta. Delay time(Sec) ,Range:000~255
；
Armed pulse out-put time. (10ms) ,Range
：
000~255 → Succeeded
37
※ [Use FP] can substitute for [Induct valid card].
F. Adding / Deleting Fingerprint or Finger-Vein
Adding
Access programming mode → User Setting → Enroll FP → Key in 5-digit user address →1 or 2 different ngers on the sensor lens → Succeeded
P.S. The AR-821EF need to collect twice for each ngerprint, and the AR-821EV need to collect three times.
2 6
Deleting
Access programming mode → User Setting → Delete FP → Key in 5-digit user address → Succeeded
P.S. If you want to delete all users’ FP, key in 99999
2 7
#
G. Access Mode
Access programming mode → User Setting
→ Access Mode
→ Key in 5-digit user address (00000~08999)
→ 0:Invalid; 1:Card; 2: Card or PIN; 3: Card and PIN
→ Finger Identify: 0: Must ; 1: Ignore
→ Succeeded
2
2
Access Mode Finger Identify Result
Hardware 701Client Hardware 701Client
0:Invalid
0: Must Just ngerprint
Just card control Invalid User
1: Ignore Just ngerprint
Just card control
1:Card
0: Must Just ngerprint
Just card control Finger+Card
1: Ignore Just ngerprint
Just card control
1. Card Only
2. Finger Only
2:Card or PIN
0: Must Just ngerprint
Just card control
1. Finger+Card
2. Finger+PIN
3. Card+Finger+PIN
4. Card+Finger+Card
5. PIN+Finger+PIN
6. PIN+Finger+Card
1: Ignore Just ngerprint
Just card control
1. Card Only
2. PIN Only
3. Finger Only
3:Card and PIN
0: Must Just ngerprint
Just card control Finger+Card+PIN
1: Ignore Just ngerprint
Just card control
1. Card+PIN
2. Finger+PIN
Copyright by SOYAL Technology Co., Ltd.. All rights reserved.
