SOYO SY-6BA+100 Bedienungsanleitung

SY-6BA+100

Motherboard

Quick Start Guide

CTested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

POST CONSUMER

RECYCLED PAPER100%

Hardware

Installation

Quick BIOS

Setup

Introduction

The SOYO CD

The ATA 66

Driver

Installation

SOYO™

SY-6BA+100 Motherboard

Pentium

III, Pentium

II & Celeron

processors

82440 BX AGP/PCI Motherboard

66&100MHz Front Side Bus supported

ATX Form Factor

Trademarks:

Soyo is a registered trademark of Soyo Computer Inc. All trademarks are the property of their

owners.

Product Rights:

Product and corporate names mentioned in this publication are used for identification purposes

only and may be registered trademarks or copyrights of their respective companies.

transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of

this publication without express written permission of Soyo Computer Inc.

Disclaimer:

Soyo Computer Inc. makes no representations or warranties regarding the contents of this

manual. We reserve the right to revise the manual or make changes in the specifications of the

product described within it at any time without notice and without obligation to notify any

person of such revision or change. The information contained in this manual is provided for

general use by our customers. Our customers should be aware that the personal computer field is

the subject of many patents. Our customers should ensure that their use of our products does not

infringe upon any patents. It is the policy of Soyo Computer Inc. to respect the valid patent rights

of third parties and not to infringe upon or assist others to infringe upon such rights.

Restricted Rights Legend:

Use, duplication, or disclosure by the Government is subject to restrictions set forth in

subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at

252.277-7013.

About This Guide:

This Quick Start Guide is for assisting system manufacturers and end users in setting up and

installing the Motherboard. Information in this guide has been carefully checked for reliability;

however, no guarantee is given as to the correctness of the contents. The information in this

document is subject to change without notice.

If you need any further information, please visit our Web Site on the Internet. The address is

"http://www.soyo.com.tw".

6BA+100 Serial - Version 1.0 - Edition: April 2000

*Thesespecificationsaresubjecttochangewithoutnotice

SY-6BA+100

Quick Start Guide

Introduction

Congratulationsonyourpurchaseofthe

SY-6BA+100

Motherboard.ThisQuickStartGuide

describesthestepsforinstallingandsettingupyournewMotherboard.

ThisguideisdesignedforalluserstoprovidethebasicstepsofMotherboardsettingand

operation.Forfurtherinformation,pleasereferto SY-6BA+100MotherboardUser'sGuide

andTechnicalReferenceonlinemanualincludedontheCD-ROMpackedwithyour

Motherboard.

Unpacking

WhenunpackingtheMotherboard,checkforthefollowingitems:

TheSY-6BA+10082440BXAGP/PCIMotherboard

TheQuickStartGuide

TheInstallationCD-ROM

SOYO3-in-1BonusPackCD-ROM(Norton

AntIVirus,GhostandVirtualDrive)

TheCPURetentionSet

OneIDEDeviceATA66FlatCable

OneIDEDeviceFlatCable

OneFloppyDiskDriveFlatCable

SY-6BA+100 Quick Start Guide

Introduction

SY-6BA+100 Motherboard Layout

Key Features

SupportsIntel®processors

-FSB66MHz:Pentium®II(233-333MHz)

&Celeron



(266-433MHz)

-FSB100MHz:Pentium®II(350-450MHz)

&Pentium®III(450-800MHz)

JumperlessandCPUvoltageAdjustable

PC98,ACPI

SupportsATA66/33(UltraDMA66/33)

Power-onbymodemoralarm

SOYOCOMBOSetup

SupportsWake-On-LAN(WOL)

Supportsonboardhardwaremonitoringand

includesHardwareDoctor™utility

SupportsCreativeSB-LINK™forPCIaudio

card

1x64-bitAGPslot

5x32-bitbusmasterPCIslots

2xUSBportsonboard

1xIrDAport

Supportsmultiple-bootfunction

Y2KCompliant

SupportsPowerFailureResume

COM 1

COM 2

PRT

USB 1USB 2

PS/2 KB

Connector

PS/2 Mouse

ConnectorJP10

PCI Slot #1

PCI Slot #2

PCI Slot #3

PCI Slot #4

PCI Slot #5

ISA Slot #1

ISA Slot #2

JP1

JP8LED1

Lithium

Battery

SB-LINK

(PC PCI)

IR1

CPUFAN

PWRFAN

ITE 8671

I/O Chipset

IDE 1

IDE4

IDE 2

IDE 3

FDC

AGP Slot

ATX

Power

Flash BIOS

Slot 1

Intel

82371 EB

DIMM 1

DIMM 2

DIMM 3

DIMM 4

8 2 8 A C

Hardware

Monitoring

Winbond

W83782M

Intel

82443 BX

CHAFAN

Speaker

Keylock

Power

LED

Tubro

LED

HDD

LED

Reset

PWRBT

JP5

Jumper

CMOS Clear

JP44

WOL

Header

ATA 33

ATA 66

SY-6BA+100

Quick Start Guide

Hardware

Installation

ToavoiddamagetoyourMotherboard, follow these simple rules while handling

thisequipment:

BeforehandlingtheMotherboard,groundyourselfbygraspinganunpaintedportion

ofthesystem's metal chassis.

RemovetheMotherboardfromitsanti-staticpackaging. Hold it by the edges and

avoidtouchingitscomponents.

ChecktheMotherboardfordamage.Ifanychipappearsloose,presscarefullytoseat

itfirmly initssocket.

Followthedirections in this sectiondesignedtoguideyouthroughaquickandcorrect

installationofyournew

SY-6BA+100

Motherboard.Fordetailedinformation,pleasereferto

SY-6BA+100MotherboardUser'sguideandTechnicalReference onlinemanualincludedon

theCD-ROMpackedwithyourMotherboard.

PREPARATIONS

Gatherandprepareallthenecessary hardware equipment to complete the installation

successfully:

Slot1processorwithbuilt-inCPUcoolingfan(boxedtype)

SDRAMmodule(s)

Computercaseandchassiswithadequatepowersupplyunit

Monitor

PS/2Keyboard

PointingDevice(PS/2 mouse)

VGACard

SoundCard(optional)

Speaker(s)(optional)

DiskDrives:HDD, CD-ROM, Floppydrive…

ExternalPeripherals:Printer,Plotter,andModem-(optional)

InternalPeripherals:ModemandLANcards(optional)

SY-6BA+100 Quick Start Guide

Hardware

Installation

Install the Motherboard

Followthestepsbelowinordertoperformtheinstallationofyournew

SY-6BA+100

Motherboard.

Step 1. Install the CPU

Mark your CPU Frequency:

RecordtheworkingfrequencyofyourCPU

thatshouldbeclearlymarkedontheCPUcover.

FSB66MHz

266MHz(66 x4.0) 333MHz(66 x5.0) 400MHz(66 x6.0) 466MHz(66 x7.0)

300MHz(66 x4.5) 366MHz(66 x5.5) 433MHz(66 x6.5)

FSB100MHz

350MHz(100 x3.5) 500MHz(100 x5.0) 650MHz(100 x6.5) 800MHz(100 x8.0)

400MHz(100 x4.0) 550MHz(100 x5.5) 700MHz(100 x7.0)

450MHz(100 x4.5) 600MHz(100 x6.0) 750MHz(100 x7.5)

CPU Mount Procedure:

Tomounttheprocessorthatyouhavepurchased

separately,followthese instructions.

Retention Module Step 1. Open the two sides by folding them up.

Step 2. Insert the CPU into the retention

module. The CPU fits in the CPU

slot in only ONE way, do not try to

force it in.

Step 3. After completely inserting the CPU,

Now your CPU is ready for use.

Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat

dissipation. Failing to install these items may result in overheating and possible burn-out of

your CPU.

SY-6BA+100

Quick Start Guide

Hardware

Installation

Step 2. Make Connections to the Motherboard

Thissectiontellshow to connect internal peripheralsandpowersupplytotheMotherboard.

InternalperipheralsincludeIDEdevices(HDD,CD-ROM),FloppyDiskDrive,ChassisFan,

FrontPanelDevices(TurboLED,InternalSpeaker,ResetButton,IDELED,and KeyLock

Switch.),Wake-On-LANcard,VGAcard,SoundCard,andotherdevices.

FormoredetailsonhowtoconnectinternalandexternalperipheralstoyournewSY-

6BA+100 Motherboard,please referto SY-6BA+100MotherboardUser'sGuideand

TechnicalReferenceonlinemanualonCD-ROM.

Connectors and Plug-ins

PCI Audio Card Header: SB-Link™(PC-PCI) Wake-On-LAN Header: JP44

Pin1 Pin2 Pin3Connect the SB-Link™(PC-PCI) cable from your

PCI audio card to this header.5VSB GND MP-Wakeup

CPU Cooling Fan: CPUFAN Power Fan: PWRFAN Chassis Fan: CHAFAN

Pin1 Pin2 Pin3 Pin1 Pin2 Pin3 Pin1 Pin2 Pin3

GND 12V SENSOR GND 12V SENSOR GND 12V SENSOR

Power LED Keylock

Pin1 Pin2 Pin3

Pin1 Pin2

5V NC GND

ControlPin GND

Speaker

Pin1 Pin2 Pin3 Pin4

5V NC NC Speakerout

HDD LED Turbo LED PWRBT RESET

Pin1 Pin2 Pin1 Pin2 Pin1 Pin2 Pin1 Pin2

LEDAnode LED

Cathode LED

Cathode GND Power

On/Off GND PowerGood GND

IrDA (Infrared Device Header): IR1

Pin1 Pin2 Pin3 Pin4 Pin5

VCC None IRRX GND IRTX

ATX Power On/Off: PWRBT ATX Power Supply: ATX PW

Connect your power switch to

this header (momentary switch

type).

To turn off the system,

please press this switch and

hold down for longer than

4 seconds.

Attach the ATX Power cable to this connector. (This

motherboardrequiresanATXpowersupply,anATpowersupply

canNOT beused.)

Note:Please make sure theATXpowersupply is ableto

provideat least 720mAofcurrent on the+5VSBlead ifyou

wantto enable theadvancedpower management functions,

likepower failure resume, Power-Onbykeyboard,etc.

Power LED

Key Lock

Speaker

Reset

PWRBT

Turbo LED

HDD LED

SY-6BA+100 Quick Start Guide

Hardware

Installation

Step 3. Configure Memory

Yourboardcomes with four DIMMsockets,providingsupportforupto1GBofmainmemory

usingDIMMmodulesfrom8MB to 256MB. For 66MHzfrontsidebusCPUsuse12nsor

fastermemory;for100MHz front side busCPUsuse8ns(100MHz,PC100compliant)

memory.

Memory Configuration Table

Number of

Memory Modules DIMM 1 DIMM 2 DIMM 3 DIMM 4

11st

21st 2nd

31st 2nd 3rd

41st 2nd 3rd 4th

RAM Type SDRAM

Memory Module

Size (MB) 8/16/32/64/128/256 Mbytes

Note:(1) 256 MB memory modules only available on PC registered DIMM.

(2) Always install memory modules in the order prescribed in this table.

(3) Do not install unbuffered and registered memory modules together.

Important:

Itis ofprimeimportancethatyouinstallDIMMmodules as outlinedinthetable

aboveinordertopreservesignalintegrityon100MHzfrontsidebussystems.

Step 4. CPU multiplier release Jumper: (JP8)

ClosingJP8canmakehighermultipliersettingsavailableonsomeINTELCPUs.For

technicaldetailsread the following:

YourPentiumCPUhas an input pinB21(100/66#signal)totellitatwhatFrontSideBus

(FSB)Frequencyitis running; JP8isconnectedtothisinputpin.TheactualFSBFrequency

ishoweversetthrough the BIOSanditmaythereforedifferfromtheFrequencyspecifiedto

theCPUthroughJP8.

BecausesomeINTELCPUshavetheirmultipliers limited at a FSB Frequency of 100MHz

andhigher,tellingtheCPUthat it is running at66MHzthoughJP8whilesettingadifferent

(higher)FSBFrequencyintheBIOSmayallow the user to set a higher multiplier value.

DoingsowillhoweverforceyourCPUtooperateoutofits specifications,andtherefore

SOYOcannotguaranteetheproperfunctioningofyoursystem.

SY-6BA+100

Quick Start Guide

Hardware

Installation

Refertothe following table:

Mode JP8

66MHz FSB clock CPUs Setting

66MHz FSB clock CPUs must use this

setting

short

100MHz FSB clock CPUs Setting

Normal

open

Possible higher multiplier limit

short

Note:Shortingthe jumperwilltelltheCPUthatitisrunningon 66MHz,thiswillreleasemore

multipliersettingsonsomeINTELCPUs,but will make the system operate out of its

specificationsiftheactualfrequency is 100 MHz or higher.

Step 5. Set the CPU Frequency

Youdonotneed to setanyjumperfortheCPUfrequency.Instead,CPUsettingsare

changedthroughtheBIOS

[SOYOCOMBOSETUP].

PleaserefertoChapter3-Quick

BIOSSetupfordetailsonhowtosettheSlot1 processor frequency.

Step 6. External Suspend Button (JP1)

Somecasescomewitha suspend button, insert the plugintoJP1.Inadditiontothisbutton,

thesystemcanalsoenterthesuspendmodethroughyourOS.

Note:Suspend modeonlyfunctionsifyourPowerManagementmodeisAPM.MakesurethattheBIOS

settingfor PowerManagementisAPM.Windows98canbeinstalledwithACPI PowerManagement

(defaultis APM),inthiscasesuspendmodewillnotfunctioneither.

Step 7. 5V Stand-by indicator LED (LED 1)

ThisLEDis lit wheneverthe5VStandbyvoltagecomingfromtheATX powersupplyis

available.Ifyouhave connected your ATX powersupply tothemains,LED1shouldbelit.

SY-6BA+100 Quick Start Guide

Hardware

Installation

IDE 1

IDE4

IDE 2

IDE 3

ATA 33ATA 66

Step 8. Enable/Disable Power-On by Keyboard (JP10)

YoucanchoosetoenablethePower-On by Keyboard function by shorting pin 1-2 onjumper

JP10,otherwise,short pin 2-3todisablethisfunction.

Power-On by

Keyboard Enable Disable

JP10 Setting Short pin 1-2 to enable

the Power-On by

Keyboard function.

Short pin 2-3 to disable

the Power-On by

Keyboard function.

Important: When using the Power-On by Keyboard function, please make sure the

ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to

meet the standard ATX specification.

Clear CMOS Data (JP5)

InsomecasestheCMOS memory may contain wrongdata,followthestepsbelowtoclear

CMOSmemory.

CleartheCMOSmemorybymomentarily shorting pin 2-3 on jumper JP5. Thisjumper

canbeeasilyidentifiedbyitswhitecoloredcap.

Thenputthe jumper backto1-2toallowwritingnewofdatainto the CMOSmemory.

CMOS Clearing Clear CMOS Data Retain CMOS Data

JP5 Setting Short pin 2-3 for

at least 5 seconds

to clear the CMOS.

Short pin 1-2 to

retain the new

settings.

Note: You must unplug the ATX power cable from the ATX power connector when

performing the CMOS Clear operation.

IDE Connectors

The6BA+100comeswithfourIDEconnectors,withsupportfor up to 8IDE

Devices.Forthesupportedinterfacemodes, refer to the table below:

IDE

Connector PIO mode DMA Mode ULTRA

DMA33

(ATA33)

ULTRA

DMA66

(ATA66)

IDE1 & 2

Yes Yes Yes No

IDE3 & 4

Yes Yes Yes Yes

Note:ItisrequiredtoconnecttheATA66 HDDs withthe ATA66flat

cabletothemotherboardto maintainproper functionalityand

stabilityoftheATA66 high speedinterface.

Andere Handbücher für SY-6BA+100

Inhaltsverzeichnis

Andere SOYO Hauptplatine Handbücher

SOYO

SOYO SY-K7VEMPRO Bedienungsanleitung

SOYO

SOYO SY-6VZA Bedienungsanleitung

SOYO

SOYO SY-K7V DRAGON Plus Bedienungsanleitung

SOYO

SOYO SY-K7AIA Bedienungsanleitung

SOYO

SOYO SY-K7VTA-B Bedienungsanleitung

SOYO

SOYO LI-7000 Bedienungsanleitung

SOYO

SOYO SY-7IWB Bedienungsanleitung

SOYO

SOYO 82430 HX/P54C Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-7VCA Bedienungsanleitung

SOYO

SOYO SY-6IBM Gebrauchs- und Pflegehandbuch

SOYO

SOYO Motherboard SY-6BA+ IV Bedienungsanleitung

SOYO

SOYO SY-K8USA DRAGON Ultra Bedienungsanleitung

SOYO

SOYO SY-5SSM Bedienungsanleitung

SOYO

SOYO SY-6VBA133-B Bedienungsanleitung

SOYO

SOYO SY-7VCA2 Bedienungsanleitung

SOYO

SOYO SY-P4I875P DRAGON 2 V1.0 Bedienungsanleitung

SOYO

SOYO SY-P4I845GE Bedienungsanleitung

SOYO

SOYO 82430 TX P54C Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-6IZA Gebrauchs- und Pflegehandbuch

SOYO

SOYO 82440 FX Bedienungsanleitung

SOYO

SOYO TechAID Bedienungsanleitung

SOYO

SOYO SY-K7ADA Bedienungsanleitung

SOYO

SOYO SY-6IWM Bedienungsanleitung

SOYO

SOYO Super 7 SY-5EMA+ Gebrauchs- und Pflegehandbuch

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung