Speco O4T8 Bedienungsanleitung
Quick Start Guide
O4T8
1Warning and Caution
■ If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to disassemble
the camera yourself. Any unauthorized changes or modifications
could void the warranty.
■ Do not allow water or liquid intrusion into the camera.
■ All installation and operation here should conform to local
electrical safety codes. Make sure the device is firmly installed
on the wall or ceiling.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use cleaning cloth to wipe it
gently.
■ Do not aim the camera at the sun or extremely bright light
sources.
■ Do not place the camera in extremely hot or cold environments
and dusty and damp locations . Do not expose it to highly
electromagnetic radiation.
■ Do not block any ventilations.
Package
2
Overview
3 Overview
3
Camera Quick start guide
CD
Screwdriver
Mounting block Terminal block for power
4 tapping screws
Side Panel Instruction
4 1
2
3
DC
Driver -
Driver +
Damp +
Damp -
1
2
3
4
Focus Adjusting
Iris Lens Plug
Focus Adjusting: When it still fails to realize focusing after having
confirmed the correct installation of lens, the back focus adjustment may
be required .
Iris Lens Plug: The camera provides an iris lens plug in negative
pattern with four square holes and the definition of pins is shown
above. The interface of DC drive auto iris adopts four pins: Damp+,
Drive+, Damp- and Drive-.
511
612
17
28
39
410
Ground
Alarm output
SD card slot
Reset
Audio input
Audio output
Video output
Power indicator
Power interface
Alarm input
Connect to PTZ
Ethernet interface
VIDEO OUT
NO
DC12V/AC24V
SD CARD
AUDIO OUT
AUDIO IN
PWR
NET
D-
COM
GND
IN D+
DEFAU LT
ALAR M RS48 5
Rear Panel Connection
Installation
4
* Before you start, please make sure that the wall is strong enough to
withstand three times the weight of the camera.
① Rotate the lens clockwise onto the lens mount of the camera.
② Plug the wire of auto iris lens to the auto iris interface of the
camera.
③ Connect the power supply and video output.
④ Attach the mounting block to the bracket which shall be supplied
by yourself and then install the bracket to the wall and tighten the
screws to fix it as shown below.
Mounting Block
Web Operation and Login
5
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.
⑤ Attach the camera to the bracket with the mounting block and
tighten the screws to fix.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins.
04 T8
Inhaltsverzeichnis
Andere Speco Digitalkamera Handbücher
Speco
Speco Internet Protocol SIP H.264 Series Bedienungsanleitung
Speco
Speco Intensifier T HTINTT5T Bedienungsanleitung
Speco
Speco Intensifier K Series Bedienungsanleitung
Speco
Speco CVC-612C Bedienungsanleitung
Speco
Speco CVC-690WD Bedienungsanleitung
Speco
Speco H8D6M Bedienungsanleitung
Speco
Speco CVC-521BC Bedienungsanleitung
Speco
Speco CVC700VFSCS Bedienungsanleitung
Speco
Speco Intensifier H HINT600VH Bedienungsanleitung
Speco
Speco CVC-544BC2 Bedienungsanleitung
