SpectraPure MarinePRO DI System Bedienungsanleitung

REV 05-05-2009

Reverse Osmosis Water Purification System

(Single and Dual Membrane Models)

The MarinePRO™ DI System

INSTALLATION AND OPERATING

MANUAL

WARNING

Please read carefully before proceeding with installation. Failure to

follow any attached instructions or operating parameter may lead to

the product’s failure and possible damage to property.

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

No part of this publication may be reproduced, stored in a retrieval system, or transmitted

in any form or by any means, electronic, mechanical, photocopying, recording or otherwise

without the prior written permission of SpectraPure Inc.

Table of Contents.........................................................................................................................2

Systems Information

System Specifications..........................................................................................................3

System Description..............................................................................................................4

Installation

System Initialization............................................................................................................5

Measuring Waste to Product Water Ratio...............................................................6-8

Flow Restrictor Removal, Adjustment and Replacement.................................9-10

Using your Systems Basic Parts

Metering & Diagnostics...................................................................................................11

Filter Diagnostics

Sediment Filter Diagnostic.............................................................................................12

Carbon Filter Diagnostic.................................................................................................13

Deionization Cartridge Diagnostic..............................................................................14

RO Membrane Diagnostic.......................................................................................15-17

Troubleshooting Guide

Troubleshooting Guide............................................................................................18-21

Tips & Storage....................................................................................................................22

Replacement & Optional Parts............................................................................................23

Warranty.......................................................................................................................................24

TABLE OF CONTENTS

Thank You for your purchase of a

SpectraPure® System. With proper

installation and maintenance, this system will provide you with high quality

water for years to come. All SpectraPure® products are rigorously tested

by us for safety and reliability. If you have any questions or concerns, please

contact our customer service department at 1.800.685.2783 or refer to our

online troubleshooting at www.spectrapure.com.

SpectraPure®Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

E-mail: [email protected] Visit us on the web www.spectrapure.com 3

SpectraPure

SYSTEM SPECIFICATIONS

Sediment Pre-Filter 1 micron MicroTec™ sediment pre-filter

Carbon Filter 1 micron carbon block pre-filter

RO Membrane Type Thin-Film Composite (TFC)

DI Cartridge Color-Indicating SilicaBuster™ Mixed-Bed

Rejection Rate Greater than 95% average

Input Water Pressure 60 psi (4.15 bar) line pressure*

Input Water Temp 77°F (25°C)

Recovery Rate 20% (i.e. 20% of the water will be collected as pure water)

Nominal Membrane Flow Rates @ 60 psi & 77° F :

GPD (lpd) Product Water Flow Rate Concentrate Flow Rate

100 (340) 235ml/min 940 ml/min

200 (680) 470ml/min 1880 ml/min

Reverse Osmosis Membrane Feed Water Requirements:

For the 1 year SpectraSelect TFC membrane pro-rated warranty to be honored, the

following conditions must be met:

Operating Pressure* 40 – 80 psi (2.75 – 5.5 bar)

pH Range 3 – 11

Maximum Temperature 100° F (38° C)

Maximum Turbidity 1.0 NTU

Maximum Silt Density Index 5.0 (based on 15 min. test time)

Maximum Chlorine less than 0.1 ppm

Maximum TDS 2000 ppm

Maximum Hardness 10 grains (170 ppm as CaCO3)

Maximum Iron less than 0.1 ppm

Maximum Manganese less than 0.1 ppm

Maximum Hydrogen Sulfide 0 ppm

Langlier Saturation Index LSI must be negative

*Operating pressure less than 40 psi will require a booster pump:

less than 49 GPD use BPLF-MO-115(-230),

more than 49 GPD use BPHF-MO-115(-230).

*Operating pressure greater than 80 psi will require a pressure reducing valve.

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

1. First, the incoming feed water is passed through a 1 micron Micro-Tec™ sediment

pre-filter. This filter is required to remove excess turbidity (particulate matter) that may

cause the membrane to plug.

2. The second stage of filtration is a1 micron carbon block pre-filter. This filter removes

organics and chlorine from the feed water that can damage the membrane.

(9,000 gal of Chlorine removal)

3. The third filtration stage of the system is a high rejection thin film composite (TFC)

reverse osmosis membrane. It removes over 98% of most inorganic salts, all

micro-organisms and almost all high molecular weight organics in the water.

4. The fourth stage moves water through a Mixed-Bed Multi-Layer They are capable

of producing 18 meg-ohm-cm resistivity water. They are the first DI cartridges

designed to reduce silica, nitrates and phosphate levels in the low ppb range. These

newly formulated cartridges far exceed the performance of previous cartridges,

offering enhanced contaminant removal, longer life and higher purity.

Caution: The deionization cartridge life is greatly reduced when operated on low pH

waters, or water with high CO2 (carbon dioxide) levels. The exact cartridge life will vary

greatly with pH, carbon dioxide levels, and TDS etc. in your RO water or the feed water

supplying the RO system. Aeration or de-gassification of RO product water is recommended

for such waters for removal of carbon dioxide.

The DI Cartridge in this system changes color when exhaustion occurs. When the cartridge

is 70% changed in color, replace.

TFC RO Membrane

(MEM-XXXX)

DI Cartridge

(DI-SB-CI-10)

Sediment Filter

(SF-MT-1-10)

Carbon Block

(CF-1-10)

IN Port

OUT Port

SYSTEM DESCRIPTION:

SpectraPure®Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

E-mail: [email protected] Visit us on the web www.spectrapure.com 5

SpectraPure

SpectraPure®Inc. assumes no responsibility for water damage due to leaks. It is

the user’s responsibility to determine that the system is leak-free.

SYSTEM INITIALIZATION:

If you are setting up your system for the first time or replacing the membrane with

a different size, p

lease follow the “

Measuring the waste to product Water Ratio”

procedure on page 6 after you do system hook-up below.

System Hook-Up

1. Attach the garden hose adapter (connected to the black tubing) to

your cold water source. Never run hot water (greater than 100° F

(38° C)) through the system.

2. Place the yellow concentrate (waste) tubing and the blue purified

(product) water tubing into a drain. Do not restrict flow from these

lines.

3. Open the cold water supply valve. You may use pressure up to 80 psi

(5.5 bar).

Check the system to ensure that all fittings are tight and leak- free

before leaving the system unattended. (If anything is leaking,

contact SpectraPure for assistance.)

Note: It is recommended that at least 2 gallons (7.57 liters) of purified

water be discarded now before collecting purified water for use. If the

unit is not used for several days, run the system for at least 10 minutes

before collecting any water. This will flush out any stale water in the

system.

4. Now follow procedure on page 6-10 to adjust the Flow Restrictor.

5. Finish the installation by connecting the yellow line to a drain. The

blue line can be placed into a Rubber Maid™ trash can or set up to

become automatic using a Liquid Level Controller (LLC-S-115 ),

(LLC-M-115) or the Auto Shut-Off Kit (ASOFK).

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

MEASURING WASTE TO PRODUCT WATER RATIO.

This procedure will assure you of maximum life and reliability of your SpectraPure

System.

Failure to perform this procedure can permanently damage the

membrane and will void Warranty.

In order to maximize the life of your SpectraPure RO Membrane, you may need to

adjust the ratio of the concentrate to purified water. If not enough concentrate is

allowed to flow past the membrane during operation, the impurities will

precipitate out on the membrane surface, clogging the RO Membrane. To keep

this from happening, the Concentrate to Purified Water Ratio must be checked

and adjusted in order to compensate for pressure and temperature variations that

exist in all water supplies. The flow rate of the concentrate must be a minimum of

4X the product flow rate. (4X to 6X is an acceptable concentrate flow rate.)

Procedure:

1. Collect product water (blue tubing) into a measuring cup for one minute.

(Measure the collected amount in milli-liters). Do the same with the waste

water (yellow tubing):

WASTE (YELLOW) IN MILLILITERS______________

DIVIDED BY

PRODUCT (BLUE) IN MILLILITERS______________

The resultant is the Concentrate to Product Ratio

(Although not needed in this procedure, the daily product flow rate in Gallons per

Day (GPD) can be calculated to be equal to the product flow rate times 0.38 ).

2. If ratio is less than 4/1:

Disconnect yellow drain line from the membrane housing and remove

flow restrictor. Use the appropriate Waste to Product ratio chart (Fig A)

to determine how long to cut the flow restrictor in order to obtain a 4:1

ratio.

EXAMPLE: If you have a 100 GPD unit (FR-90), and your product flow is

175 ml/.min, than the flow restrictor needs to be cut to a total length

of 6 inches (15.2 cm)

3. If ratio is greater than 6:1, flow restrictor requires replacement

(Please contact SpectraPure Inc).

This completes the procedure.

SpectraPure®Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

E-mail: [email protected] Visit us on the web www.spectrapure.com 7

SpectraPure

Fig. A: Flow Restrictor Tables

(For 4:1 Concentrate to Product Ratio)

ml./min. gpd in. cm.

269 102 1 2.5

233 88 2 5.1

213 81 3 7.6

198 75 4 10.2

183 69 5 12.7

175 67 6 15.2

164 62 7 17.8

154 58 8 20.3

148 56 9 22.9

141 54 10 25.4

136 52 11 27.9

133 50 12 30.5

129 49 13 33.0

128 48 14 35.6

124 47 15 38.1

124 47 16 40.6

PRODUCT RATE CUT TO LENGTH

ml./min. gpd in. cm.

490 186 1 2.5

460 175 2 5.1

430 163 3 7.6

400 152 4 10.2

379 144 5 12.7

356 135 6 15.2

344 131 7 17.8

326 124 8 20.3

311 118 9 22.9

300 114 10 25.4

289 110 11 27.9

281 107 12 30.5

270 103 13 33.0

263 100 14 35.6

259 98 15 38.1

256 97 16 40.6

PRODUCT RATE CUT TO LENGTH

(GREEN)

(YELLOW)

FR-100

FR-200

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

SINGLE MEMBRANE SYSTEM (FIG B)

DUAL MEMBRANE SYSTEM (FIG C)

1/4” BLACK LINE: Tap Water

1/4” BLUE LINE: Product Water

1/4” YELLOW LINE: Waste Water

(Flow Restrictor is inside the

Waste line)

SpectraPure®Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

E-mail: [email protected] Visit us on the web www.spectrapure.com 9

SpectraPure

FLOW RESTRICTOR REMOVAL, ADJUSTMENT & REPLACEMENT

1. Locate the yellow concentrate tubing (Fig. B) (for Dual-Membrane System

Fig. C).Remove the tubing from its push-fitting at the membrane as follows:

a.) Firmly depress and hold the push-fitting collar down with your

thumbnail.

b.) While the push-fitting collar is depressed, pull the tubing straight

out of the push-fitting. Once the tubing is removed, release the

collar.

2. Carefully remove the flow restrictor assembly, now visible as a plastic insert In

the end of the yellow tubing (Fig. D). You may use an object such as a dull

knife to help pry the flow restrictor insert from the end of the tubing. The

entire flow restrictor (consisting of the insert collar and thin capillary tubing)

may then be gently extracted.

Note: Take care not to crush or otherwise damage the delicate capillary tubing.

3. Refer to the Flow Restrictor Tables (Fig. A). Find the table that represents the

Flow Restrictor Assembly for the system that you have. Find the product

flow rate in the left-hand column and the length of the

flow restrictor in the right-hand column.

Example: If your Flow Restrictor Assembly is for a 90 GPD Membrane and

the product flow rate is 170 mL/Min, then the flow restrictor length should

be cut to 6.5 inches (16.5 mm). 170 is about halfway between 164 (7 in.)

and 175 (6 in.).

4. Using a new single-edge razor blade, carefully measure and then cut the

flow restrictor to the total length indicated.

5. Re-insert the flow restrictor assembly into the yellow tubing and firmly

re-seat the insert into the end of the yellow tubing by carefully pressing on

the insert with your thumbnail. Care should be taken not to crush or

otherwise damage the end of the capillary tubing protruding from the end

of the insert.

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

6. Re-insert the yellow tubing into its push-fitting in the RO membrane

as follows:

a.) Moisten the O-ring seal inside the concentrate outlet fitting

by dripping a few drops of clean water into the fitting.

b.) Grasp the yellow tubing near the flow restrictor end, and

insert the tubing into the push-fitting. Push the tubing into

the fitting until resistance is felt, approximately 1/2 inch

(12.7 mm). The tubing is now seated on the O-ring seal

inside the fitting.

c.) Firmly push the tubing approximately an additional 1/4 inch

6.35 mm) further into the fitting to completely seat the line

into the fitting and O-ring seal.

7. Turn on the system’s water supply and check for leaks prior to further

use or testing. If a leak is observed, you may not have pushed the

yellow tubing into the push-fitting far enough to seal the tubing

against the O-ring. Turn off the system water supply and re-seat the

tubing as described above.

YELLOW TUBING:

(Disconnected

from membrane

housing’s fitting.

)

CAPILLARY TUBE:

(Specific diameters are

matched for each size

membrane to restrict

the flow of waste

water leaving the RO

membrane’s housing.)

PLASTIC INSERT: (Insert keeps

capillary tube in the yellow line and

prevents it from washing down the

drain. It also forces waste water to

flow through the capillary tubing to

restrict waste water as it leaves the

housing.)

Fig. D: Flow Restrictor Assembly

Inhaltsverzeichnis

Andere SpectraPure Wasserfiltersystem Handbücher

SpectraPure

SpectraPure Mega MaxCap Bedienungsanleitung

SpectraPure

SpectraPure MaxCap MC-RODI-90-10-MF Bedienungsanleitung

SpectraPure

SpectraPure MAXCAP RO/DI Bedienungsanleitung

SpectraPure

SpectraPure MAXCAP D1 Bedienungsanleitung

SpectraPure

SpectraPure Eliminator RO 100-LP Bedienungsanleitung

SpectraPure

SpectraPure The Eliminator RO System Bedienungsanleitung

SpectraPure

SpectraPure CSP Series Bedienungsanleitung

SpectraPure

SpectraPure CSPDI-180 Bedienungsanleitung

SpectraPure

SpectraPure MaxPure MPDI RO/DI System Bedienungsanleitung

SpectraPure

SpectraPure CR-RODI-90-10 Bedienungsanleitung

SpectraPure

SpectraPure Single 90 Bedienungsanleitung

SpectraPure

SpectraPure MPRO RO System Bedienungsanleitung

SpectraPure

SpectraPure MaxCap MC-RODI-180-MF Bedienungsanleitung

SpectraPure

SpectraPure MaxPure MPRO-300 RO System Bedienungsanleitung

SpectraPure

SpectraPure CSPDI-90-MF Bedienungsanleitung

SpectraPure

SpectraPure PSP-600 Bedienungsanleitung

SpectraPure

SpectraPure 4-Stage Compact DWS-CLS-3 Bedienungsanleitung

SpectraPure

SpectraPure PERFORMANCE PLUS MC-RODI-100-PPLUS Originalbetriebsanleitung

SpectraPure

SpectraPure 100 GPD U.H.E RO/DI Originalbetriebsanleitung

SpectraPure

SpectraPure MAXCAP RO Bedienungsanleitung

SpectraPure

SpectraPure The Eliminator DI Bedienungsanleitung

SpectraPure

SpectraPure MaxPure MPDI-90 GPD Bedienungsanleitung

SpectraPure

SpectraPure SP-RO-90 RO BASIC Bedienungsanleitung

SpectraPure

SpectraPure SpectraPlus 2000 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung