Spectrum Digital XDS510PP Bedienungsanleitung

XDS510PP

MPSD Emulator Pod

1997 DSP Development Systems

Installation

Guide

XDS510PP

MPSD Emulator Pod

Installation Guide

502222-0001 Rev. C

April 1997

SPECTRUM DIGITAL, INC.

10853 Rockley Road Houston, TX. 77099

Tel: 281/561-6952 Fax: 281/561-6037

[email protected] www.spectrumdigital.com

IMPORTANT NOTICE

Spectrum Digital, Inc. reserves the right to make changes to its products or to discontinue any

product or service without notice, and advises its customers to obtain the latest version of relevant

information to verify, before placing orders, that the information being relied on is current.

Spectrum Digital, Inc. warrants performance of its products and related software to current

specifications in accordance with Spectrum Digital’s standard warranty. Testing and other quality

control techniques are utilized to the extent deemed necessary to support this warranty.

Please be aware that the products described herein are not intended for use in life-support

appliances, devices, or systems. Spectrum Digital does not warrant nor is liable for the product

described herein to be used in other than a development environment.

Spectrum Digital, Inc. assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein. Nor does Spectrum

Digital warrant or represent any license, either express or implied, is granted under any patent right,

combination, machine, or process in which such Digital Signal Processing development products or

services might be or are used.

WARNING

This equipment is intended for use in a laboratory test environment only. It generates, uses, and can

radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable

protection against radio frequency interference. Operation of this equipment in other environments

may cause interference with radio communications, in which case the user at his own expense will be

required to take whatever measures may be required to correct this interference.

TRADEMARKS

MS-DOS, MS-Windows, and Windows 95 are registered trademarks of Microsoft Corp.

Contents

1 Installing the Emulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Lists the hardware and software you’ll need to install the XDS510 emulator pod.

1.1 What You’ll Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Hardware checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Software checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.2 Step 1: Connecting the Emulator to your PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Preparing the emulator for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.3 Step 2: Connecting the Emulator to Your Target System . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Setting up the “XDS510PP.INI” file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Resetting the emulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.4 Utility Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2 Specifications for Your Target System’s Connection to the Emulator . . . . . . . . . . . . . . 2-1

Contains information about constructing a 14-pin connector on your target system and

information about connecting the emulator to the target system.

2.1 Designing Your Target System’s Emulator Connector (14-pin Header) . . . . . . . . . . . . . . 2-2

2.2 Bus Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.3 Emulator Pod Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.4 Emulator Pod Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.5 Buffering Signals Between the Emulator and the Target System . . . . . . . . . . . . . . . . . 2-7

2.6 Emulation Timing Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2.7 Mechanical Dimensions for the 12-Pin Emulator Connector . . . . . . . . . . . . . . . . . . . . . 2-13

1-1

Chapter 1

Installing the

XDS510PP MPSD Emulator Pod

This chapter helps you install the XDS510PP MPSD emulator pod on a PC

running Windows or Windows 95. When you complete the installation,

refer to the appropriate C Source Debugger User’s Guide for software

installation.

Topic Page

1.1 What You’ll Need 1-2

Hardware checklist 1-2

Software checklist 1-2

1.2 Step 1: Connecting the Emulator to your PC 1-3

Preparing the Emulator pod for installation 1-3

1.3 Step 2: Connecting the Emulator to Your

Target System 1-4

Setting up the “XDS510PP.INI” file 1-5

Resetting the emulator 1-6

1.4 Utility Programs 1-6

Spectrum Digital, Inc

1-2 XDS510PP MPSD Emulator Pod Installation Guide

1.1 What You’ll Need

The following checklists detail items that are shipped with the XDS510PP

MPSD emulator and additional items you’ll need to use these tools.

Hardware checklist

__ host An IBM PC/AT or compatible ISA/EISA-based PC with a hard-

disk system and a 1.44M floppy-disk drive

__ memory Minimum of 640K; in addition, if you are running under Microsoft

Windows, you’ll need at least 256K of extended memory

__ display Monochrome or color (color recommended)

__ parallel port One centronics printer port, bidirectional for 4 bit, 8 bit, or EPP

compatible,

__ emulator module 5 Volts DC (125 milliamps)

power requirements

__ target system A board with an appropriate target device

__ connector to 12-pin connector (two rows of six pins) --- see Chapter 2 for

target system more information about this connector

__ optional hardware A Microsoft-compatible mouse

An EGA or VGA compatible graphics display card and a large monitor.

The debugger has several options that allow you to change the overall

size of the debugger display. If you have an EGA or VGA compatible

graphics card, you can take advantage of some of these larger screen

sizes. These larger screen sizes are most effective when used with a

large (17” or 19”) monitor. (To use a larger screen size, you must

invoke the debugger with an appropriate option. For more information

about options, refer to the invocation section in Chapter 1, Overview

of a Code Development and Debugging System, in the TMS32OC5x

C Source Debugger User’s Guide.)

__ miscellaneous Blank, formatted disks

materials 25 Conductor Printer Cable

Software checklist

__ operating system Micrsoft Windows 3.1 or Windows 95

__ required file emurst.exe resets the XDS510PP emulator pod

Spectrum Digital, Inc

1-3

1.2 Step 1: Installing the XDS510PP MPSD Emulator Pod

This section contains the hardware installation information for the emulator pod.

Preparing the emulator board for installation

The printer port connection on the back of the PC is a 25 Pin Female D connector.

Connect one end of the supplied cable to the printer port that you intend to use

(LPT1 or LPT2). Connect the other end of the cable to the 25 pin connector on the

XDS510PP emulator pod. The XDS510PP is also known as a scan path adapter.

The XDS510PP can be powered from two different sources. The easiest is to use

power from the target system. This is done automatically when the target cable is

connected. The pod uses the PD pin on the cable. The trace going to this pin on the

target board must be able to carry the current requirements of the pod. The second

source of power is the included 5 volt power supply

Warning: The power input to the pod must be regulated. Voltages higher than 5 volts

will destroy the emulator

Note: The external power supply must be used for 3 volt target systems.

Do not connect or disconnect the 25-pin D connector while the PC is powered up.

Do not connect or disconnect the 12-pin cable while the target system is powered up.

Target Cable Connectors:

Be very careful with the target cable connectors. connect them gently; don’t force

them into position, or you may damage the connectors.

Spectrum Digital, Inc

1-4 XDS510PP MPSD Emulator Pod Installation Guide

1.3 Step 2: Connecting the XDS510PP to Your Target System

Figure 1-1 shows how you connect the XDS510PP emulator pod and 25 conductor

cable to your target system. In most cases, the target system will be a target board

of your own design.

Figure 1-1. Connecting the XDS510PP Emulator Pod to Your Target System

EscNum Scroll SysLockLock Req

789

456

123

HomePgUp

EndPgDn

InsDel

PrtSc

Break

Ctrl

Shift Shift

Alt Caps

Lock

Enter

~! @ # $ % ^ & * ( ) _ + |

`1234567890-=\

QWE R TY U I OP

ASDFGHJKL

ZXCVBNM

{}

[]

<>?

,./

F1F2

F3F4

F5F6

F7F8

F9F10

C3X DSP 12- pin connector D-sub connector

25-pin male

XDS510PP Emulator Pod

25 Conductor Cable

port on PC)

(Plugs into parallel

D-sub connector

25 pin male

12 - pin header

XDS510PP

ACTIVE

POWER [5VDC]

PRINTERPORT

for example

Spectrum Digital, Inc

1-5

Setting up the XDS510PP.INI file

The xds510pp.ini file is used to set driver parameters. The “.INI” should be located in

the same directory as the HLL Debugger. The D_DIR environment variable is used to

select the Debugger directory. If the xds510pp.ini file doesn’t exist or can’t be found

certain parameters are used as default. Shown below are the parameters and their

defaults.

speed = 25

mode = spp4

port -p command line parameter, or 240 if no command line

When the xds510pp.ini file is invoked there are four parameters which can be used.

These parameters are: speed, port, mode, and timing.

The ‘speed’ parameter selects the amount of delay between port accesses. The higher

the value the more delay added. A good value to start with is 25.

example: speed = 25

The ‘port’ parameter selects the PC’s printer port. The default value is 378. Other

values are 278 and 3BC.

example: port = 278

The mode parameter selects the type of hardware supported by the host PC. The three

modes are shown in the table below:

The “spp4” mode should work on all machines, but is the slowest. The “spp8” mode

requires a bidirectional parallel port. The “epp” mode is the fastest but requires an EPP

compatible parallel port on the host PC. If you are using EPP mode you must make

sure the PC is configured for EPP operation. Check the documentation that came with

the PC or add-in card on how to configure the parallel port. The default mode is “spp4”.

example: mode = epp

Table 1: Parallel Port Modes

Modes Description

spp4 standard parallel port

spp8 bi-directional port

epp enhanced parallel port

Spectrum Digital, Inc

1-6 XDS510PP MPSD Emulator Pod Installation Guide

The timing parameter is used to select alternate timing for the TDI and TMS signals.

The default operation is to change the state of these signals on the falling edge of the

TCK_RET signal. When alternate timing is selected TDI and TMS are changed to the

rising edge of the clock. The default mode is to use the default timing.

example: timing = alternate

As shipped from the factory the xds510pp.ini file has the parameters set as:

speed = 25

mode = epp

port = 378

Resetting the emulator

To reset the emulator, execute the emurst.exe file from the file manager or explorer.

The emulator should respond with no errors.

1.4 Utility Programs

There are several utility programs that can be found in the installation directory. One

such program is “PORTCHK”. This program searches for parallel ports and tries to

detect if they are bi-directional. To run this program type “PORTCHK” at the

command line prompt. This program does not require any arguments.

There may be other utility programs on the diskette that is shipped with the

XDS510PP. These programs may aid you in installing the XDS510PP on a

particular PC hardware configuration. Refer to the ‘readme’ files or the ‘port

utilities’ manual for their use.

Inhaltsverzeichnis

Andere Spectrum Digital Computerhardware Handbücher

Spectrum Digital

Spectrum Digital XDS560R Bedienungsanleitung

Spectrum Digital

Spectrum Digital C2000 Series Gebrauchs- und Pflegehandbuch

Spectrum Digital

Spectrum Digital XEVM642 4VSX35 Gebrauchs- und Pflegehandbuch

Spectrum Digital

Spectrum Digital XDS510USB Bedienungsanleitung

Spectrum Digital

Spectrum Digital XDS560R Bedienungsanleitung

Spectrum Digital

Spectrum Digital XDS560v2 Gebrauchs- und Pflegehandbuch

Spectrum Digital

Spectrum Digital AppBox C21 Bedienungsanleitung

Spectrum Digital

Spectrum Digital TMS320C5515 eZdsp Gebrauchs- und Pflegehandbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung