Spectrum Digital AppBox D21 Bedienungsanleitung

AppBox D21 System User’s Guide 1 AppBox

Specializes in

designing with

Microchip

products

AppBox D21

System User’s

Guide

AppBox D21 System User’s Guide 2 AppBox

Notice !

Spectrum Digital, Inc (SDI) provides the enclosed product under the following conditions:

The user/customer assumes all responsibility and liability for the proper use, storage, and safe handling

of the product. Further, the user indemnifies SDI from all claims arising from the use, installation, storage,

and handling of the product. Due to the flexibility and open construction of the product, it is the user’s

responsibility to take all appropriate precautions with regard to powering, attachment of cables,

connection to other equipment, and electrostatic discharge.

Except to the extent of the indemnity set forth above, neither party shall be liable to the other for any

indirect, special, incidental, or consequential damages.

SDI assumes no liability for applications assistance, customer product design, system and software

performance, or infringements of patents or services described herein.

No license is granted under any patent right or other intellectual property right of SDI covering or relating

to any machines, process, software, or combination in which such SDI products or services might be or

are used.

SDI currently deals with a variety of customers for products, and therefore our arrangement with the

reseller, customer, or user is not exclusive.

Please refer to the product web page on the SDI web site for warranty period.

The warranty and return policy are described on the SDI web site.

Mailing address:

Spectrum Digital, Inc

PO Box 1559

Sugar Land, TX. 77487-1559

Web site: www.spectrumdigital.com

Sales: [email protected]

Support: support@spectrumdigital.com

519108-4001

AppBox D21 System User’s Guide 3 AppBox

Table of Contents

Section Title Page

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 AppBox D21 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 What’s Included In The AppBox D21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 AppBox D21 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 AppBox D21 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5 AppBox D21 Communication Expansion . . . . . . . . . . . . . . . . . . . . . . . 6

1.6 AppBox D21 Software Development Tools . . . . . . . . . . . . . . . . . . . . . . . 6

2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Attaching Power to the AppBox D21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Installation of AppIO Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Attachment of the Distribution Box to the AppBox D21 . . . . . . . . . . . . . . . . . 9

2.4 Installation of Atmel-ICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.0 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.1 J1, Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1.2 J2, RS485 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.1.3 J3, USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1.4 J6, Cortex-M Debug Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1.5 AppIO Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.1.5.1 EXT1, AppIO Module 1 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.1.5.2 EXT2, AppIO Module 2 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.1.5.3 EXT3, AppIO Module 3 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.2 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.5 Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.0 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.0 Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.0 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

AppBox D21 System User’s Guide 4 AppBox

1.0 Introduction

This document describes the features of the AppBox D21. The AppBox D21 is designed to be used in an

industrial environment with a USB, or RS-485 interface and provide flexible, modular I/O (AppIO) for specific

applications. These AppIO Modules allow customized solutions to be integrated for a wide variety of

applications that need to go into a USB or RS-485 communications environment.

1.1 Features

This AppBox D21 has the following features:

Atmel ATSAMD21J18A processor (ARM Cortex-M0+), maximum frequency 48 MHz.

Operates on +12 to +24 volts DC, uses less than 500 Ma. at +12V

USB interface for industrial computer systems

RS485 communications for industrial systems

Communication interface expansion via Distribution Box (sold separately)

Modular I/O expansion via up to three (3) AppIO Modules, Atmel X PLAINED compatible

Fully enclosed system with knock out panels for AppIO Modules (sold separately)

Convenient enclosure mounting holes

Vented enclosure for cooling

Front panel push button switch

Front panel programmable LED

Atmel-ICE debug header present for development

Operates 0 - +70C

D21 CPU BOARD AppIO

Module #1

AppIO

Module #3

AppIO

Module #2

RS485

Power

+12-24 VDC Interface #3

Interface #1

Interface #2

User Defined

AppBox D21 Block Diagram

LED

Push

Button

Switch Comms

Select

Switch

ATSAMD21J18A

USB

Atmel-ICE

Header

LED1

SW1

EXT1

EXT2

EXT3

AppBox D21 System User’s Guide 5 AppBox

1.2 What’s Included In the AppBox D21

The Spectrum Digital AppBox D21 product (Part/SKU #: 703910-0001) includes:

AppBox D21 in anti-static bag

Terminal block header for power input

Product information card

NOTE: This product does not include any software or drivers. Development tools (Atmel-ICE and

Software code generation suite) can be obtained from Microchip/Atmel at:

https://www.microchip.com/development-tools/.

1.3 AppBox D21 Front Panel

The features of the front panel on the AppBox D21 are shown in the figure below:

1.4 AppBox D21 Accessories

The following accessories for the AppBox D21 can be ordered from Spectrum Digital or authorized resellers:

Accessory Description Part/SKU Number

AppBox Power Supply with cable,

110/220 VAC to 12 VDC, 1.5A 703925-0001

Distribution Box 703924-0001

AppBox Cable 703923-0001

RS485 cable 703917-0001

USB-RS485 cable 703914-0001

SW1 J1

J2LED1 AppBox D21 Front Panel

USB

AppBox D21 System User’s Guide 6 AppBox

1.5 AppBox D21 Communication Expansion

The J2 connector on the AppBox D21 presents multiple communication interfaces. The standard factory

cables only support one interface at a time. To have access to multiple communication interfaces a

Distribution Box (Part/SKU #: 703924-0001) and AppBox cable (Part/SKU #: 703923-0001) are required.

The Distribution Box expands the J2 connector to four (4) images of the AppBox D21 J2 connector. The

AppBox cable bridges all signals on the AppBox D21 J2 connector to a connector on the Distribution Box.

Be aware that one of the Distribution Box connectors will be used for the AppBox bridging cable leaving

3 connectors to be used for communication interfaces. All cables that can plug into the J2 connector on the

AppBox D21 can plug into the Distribution Box.

The user should enable all interfaces they want to use with the Distribution Box by setting the switch positions

on Switch SW2, position 1. See section 3.3.

The AppBox D21 and Distribution Box system configuration is shown in the figure below:

1.6 AppBox D21 Software Development Tools

The AppBox D21 is compatible with the software and hardware development tools from Microchip/Atmel.

These tools are described on the Microchip/Atmel website:

https://www.microchip.com/development-tools/

These tools include the following:

Editor

Compiler/assembler/linker

Libraries

Operating System

Debugger

JTAG Emulator

RS485

AppBox D21 with Distribution Box

Distribution Box

AppBox D21

J2 Connector

AppBox Cable

AppBox D21 System User’s Guide 7 AppBox

2.0 Installation

2.1 Attaching Power to the AppBox D21

Power can be provided to the AppBox D21 by two different means; the AppBox power supply with cable

(Part/SKU #: 703925-0001), or wiring the 2 position terminal block header (included with AppBox D21) that

plugs into the D21 CPU Board’s power input connector. See the figure below.

Listed below are the steps to install the terminal block header power connector (included in kit) into the

AppBox D21.

1. Cut 2 pieces of wire (preferably 1 red for positive-VIN, 1 black for negative-DGND) to the desired

length for your application. This wire should be 22 gauge or heavier

2. Strip ¼ inch (6-7 mm) of insulation from one end of each wire.

3. Position the terminal block header on a flat surface with the key stubs up and away from you. See

the figure below.

4. Insert the negative/DGND wire (black) into the left wire hole and tighten the screw.

5. Insert the positive/VIN wire (red or black with strip) into the right wire hole and tighten the screw.

6. The terminal header should look like the figure below.

7. Pull/tug on the wires to insure they are secure in the terminal block.

Terminal Block Header

AppBox Power Connector

Positive

VIN

Negative

DGND

Wired Terminal Block Header

Positive

VIN

Negative

DGND

Screw

AppBox D21 System User’s Guide 8 AppBox

8. Attach the loose end of the wires to a +12 – 24 VDC power source. Be sure of the polarity. This

power source should supply at least 1 amp of current. This requirement will vary

depending on the current requirements of the C21 CPU Board and the AppIO Modules.

9. Turn on the power source.

10. With a multi-meter or oscilloscope measure the voltage at the terminal block header to verify

+12 -24 VDC is present. Place the meter/scope probes on the 2 screws to measure.

11. Turn off the power source

12. Insert the terminal block header into the power input of the AppBox D21.

13. Turn on the power source.

2.2 Installation of AppIO Modules

Listed below are the steps to install AppIO Modules in the AppBox D21:

1. Remove ALL power to the AppBox enclosure

2. Remove all interface connections attached to the installed AppIO Modules

3. Remove the USB/RS-485 cables to the D21 processor board

4. Turn the AppBox over and remove the 2 screws from the bottom of the enclosure as shown

below

5. Turn the AppBox back over (label showing) and lift the top off the enclosure being careful not to

lose the knockout panels

6. If necessary remove one or more existing AppIO Modules and associated knockout panels by

unscrewing the 2 screws

7. Plug the new AppIO Module(s) into EXT1, EXT2, or EXT3 on the D21 CPU Board

Screws

Box Bottom Screw Locations

IO Module

ttached to D21 CPU Board

D21 CPU

Board

AppIO Knockout

Panel

AppIO Module

Screw

AppBox D21 System User’s Guide 9 AppBox

8. Insert the included knock out panel associated with this AppIO Module

9. Insert and tighten the 2 screws for the AppIO Module

10. Insert the knock out panels in any unused positions

11. Place the cover back over the D21 processor board and AppIO Modules

12. Insert the 2 screws back in and tighten until snug, do not over tighten/strip the screws

13. Re-attach the USB/RS-485 connections to the processor board

14. Re-attach all interface connections to the AppIO Modules

15. Apply power to the AppBox D21

2.3 Attachment of Distribution Box to the AppBox D21

Listed below are the steps to attach the Distribution Box (Part/SKU #: 903924-0001) to the AppBox D21:

1. Remove ALL power to the AppBox D21 enclosure

2. Remove any communication cables from the J2 connector on the AppBox D21

3. Plug one end of the AppBox cable (Part/SKU #: 703923-0001) into the J2 connector on the

AppBox D21

4. Plug the other end of the AppBox cable into one of the connectors on the Distribution Box

5. Plug the desired communication cables into the Distribution Box

6. Make all other connections before powering

7. Apply power to the AppBox D21

Box D21 with A

IO Module Installed

AppIO Module

Connector

AppIO Knockout

Panel

Box D21 Connected to Distribution Box

AppBox

AppBox Cable

Distribution Box

AppBox D21 System User’s Guide 10 AppBox

2.4 Installation of Atmel-ICE emulator

Listed below are the steps to install Atmel-ICE emulator:

1. Remove ALL power to the AppBox D21 enclosure

2. Remove all interface connections attached to the AppIO Modules

3. Remove the USB/RS-485 connections to the processor Module

4. Turn the AppBox over and remove the 2 screws from the bottom of the enclosure as shown

below

5. Turn the AppBox back over (label showing) and lift the top off the enclosure being careful not to

lose the knockout panels

6. Plug the emulator end of the ribbon cable into the “SAM” Port on the emulator

7. Plug in the Atmel-ICE debug into connector J6 on the AppBox D21 CPU board. Visually inspect

the connection to insure all the board pins are in the female cable connector.

8. Re-attach the USB/RS-485 connections to the processor board

9. Re-attach all interface connections to the AppIO Modules

10. Apply power to the AppBox D21

11. Start debug session on the host computer

Screws

Box Bottom Screw Locations

D21 CPU Board

Atmel-ICE Attached to A

Box D21 CPU Board

Atmel-ICE

J6 Connector

RED Wire

SAM Port

Inhaltsverzeichnis

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-682C Series Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung