Spectrum EGD-24 Beilage







Model Voltage Power (W) Amps Dimensions (inches) Temperatures

Width Depth Height 0C 0F

EGD-24 208/240 V 4200/5600 20.2/23.4A 24" 21.7" 12.9" 65-250C 150-480F

EGD-36 208/240 V 6300/8400W 30/35A 36" 21.8" 12.9" 65-250C 150-480F

BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS

Congratulations on your purchase of SPECTRUM commercial cooking equipment. SPECTRUM takes pride in the design

and quality of our products. When used as intended and with proper care and maintenance, you will experience years of

reliable operation from this equipment. To ensure best results, it is important that you read and follow the instructions in

this manual carefully. It’s important to save these instructions for future reference.

EGD-36

EGD-24

C US LISTED

SPECTRUM products have undergone strict product testing in order to comply with regulatory standards

and specications set by international independent, commonwealth and federal authorities.

As testimony to such compliance SPECTRUM products carry the following marks/symbols:



Important For Future Reference

Introduction

Congratulations on the purchase of your SPECTRUM machine. Please

take time to carefully read through this manual to ensure the machine

is operated and maintained properly, to ensure the best possible

performance from the product for many years.

SPECTRUM will not accept liability for the following if:

• The instructions in this manual have not been followed correctly.

• Non-authorized personnel have tampered with the machine.

• Non-original spare parts are used.

• The machine has not been handled and cleaned correctly.

• There is any use damage to the unit.

Please complete this information and retain this manual for the life of the equipment. For

Warranty Service and/or parts, this information is required.

Model Number Serial Number Date Purchased

! !

WARNING: IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE

PROPERTY DAMAGE, INJURY, OR DEATH. READ THE

INSTALLATION, OPERATION, AND MAINTENANCE

INSTRUCTIONS THOROUGHLY BEFORE INSTALLING

OR SERVICING THIS EQUIPMENT.

AVERTISSEMENT: TOUTE INSTALLATION, RÉGLAGE,

MODIFICATION, RÉPARATION OU ENTRETIEN

INCORRECT PEUT OCCASIONNER DES DOMMAGES

MATÉRIELS, DES BLESSURES GRAVES OU LA MORT.

LIRE LES INTRUCTIONS D'INSTALLATION, D'UTILISATION ET

D'ENTRETIEN ATTENTIVEMENT AVANT D'INSTALLER OU DE

RÉPARER CET APPAREIL.

! !

CAUTION: THESE MODELS ARE DESIGNED, BUILT, AND

SOLD FOR COMMERCIAL USE ONLY. IF THESE MODELS

ARE POSITIONED SO THE GENERAL PUBLIC CAN USE

THE EQUIPMENT, MAKE SURE THAT CAUTION SIGNS,

WARNINGS, AND OPERATING INSTRUCTIONS ARE

CLEARLY POSTED NEAR EACH UNIT SO THAT ANYONE

USING THE EQUIPMENT WILL USE IT CORRECTLY AND

NOT INJURE THEMSELVES OR HARM THE EQUIPMENT.

ATTENTION: CES MODÈLES SONT CONÇUS, FABRIQUÉS,

ET VENDUS POUR UN USAGE COMMERCIAL SEULEMENT.

SI CES MODÈLES SONT PLACÉS POUR QUE LE GRAND

PUBLIC PUISSE LES UTILISER, ASSUREZVOUS QUE LES CONSIGNES

D’ATTENTION, D'AVERTISSEMENT, ET LES INSTRUCTIONS

D'UTILISATION SOIENT CLAIREMENT AFFICHÉES PRÈS DE

CHAQUE UNITÉ DE SORTE QUE N'IMPORTE QUEL UTILISATEUR DE

L'APPAREIL L'EMPLOIE CORRECTEMENT ET NE SE BLESSE PAS OU

N'ENDOMMAGE PAS L'APPAREIL.

! !

WARNING: A FACTORY AUTHORIZED SERVICE

PROVIDER SHOULD HANDLE ALL MAINTENANCE

AND REPAIR. BEFORE DOING ANY MAINTENANCE

OR REPAIR, FOLLOW SERVICE SET UP ARRANGEMENT

ON PAGE 11.

AVERTISSEMENT: UN TECHNICIEN AUTORISÉ PAR

L'USINE DEVRA EFFECTUER TOUT L'ENTRETIEN ET LES

RÉPARATIONS. AVANT DE FAIRE TOUT ENTRETIEN OU

RÉPARATION, VEUILLEZ CONTACTER WINCO.

Proper Grounding · Mise à la terre correcte

This machine is provided with a three-pronged

grounding plug. The outlet to which this plug

is connected must be properly grounded. If the

receptacle is not the proper grounding type, contact an

electrician. DO NOT, under any circumstances, cut

or remove the third ground prong from the power cord

or use any adapter plug.

Cette machine est équipée d'une che à trois broches.

La prise sur laquelle cette che est branchée doit être

correctement mise à la terre. Si la prise n'est pas le type de

mise à la terre, contactez avec un électricien. NE PAS, en

aucun cas couper ou enlever la troisième broche de terre à

partir du cordon d'alimentation ou utiliser un adaptateur.

USE A GROUNDED OUTLET

DO NOT ADD AN ADAPTOR

TO THE PLUG

UTILISER UNE PRISE AVEC MISE

À LA TERRE NE PAS AJOUTER UN

ADAPTATEUR SUR LA FICHE



Table of Contents

Specications .............................................................................. 1

Warnings ..................................................................................... 2

Introduction ................................................................................ 2

Table of Contents ....................................................................... 3

Packaging .................................................................................... 3

Installation .................................................................................. 4

Operation .................................................................................... 5

Cleaning, Care & Maintenance ................................................. 6

Safety ........................................................................................... 7

Troubleshooting ......................................................................... 7

Service & Repair .......................................................................... 7

Exploded View ........................................................................... 8

Spare Parts List ............................................................................ 9

Electrical Diagram .................................................................... 10

Limited Warranty ......................................................................11

Package Contents

All units come with Installation & Operating Instructions Manual

and the following:

• Griddle

• Catch Tray

SPECTRUM prides itself on quality and service, ensuring that at the

time of packing, all products are supplied fully functional and free

of damage. Should you nd any damage as a result of freight, please

contact your SPECTRUM dealer immediately.

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN

ENVIRONMENTALLY RESPONSIBLE MANNER.

1. Remove all packing materials and tape, as well as any protective

plastic and cardboard, from the unit.

2. Clean any glue residue left over from the plastic or tape.

3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN

PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES

ARENEEDED.

Please keep this manual in a safe place for future use!

NOTE

Please remember that this manual and the warning labels do not replace the need to be alert, to properly train and supervise

operators, and to use common sense when using this equipment.

Installation

NOTE

IF CERTIFIED RECEPTACLE IS REQUIRED, IT MUST BE INSTALLED BY

A QUALIFIED ELECTRICIAN WHO IS FAMILIAR WITH ELECTRICAL

PROCEDURES AND CODES. DO NOT ATTEMPT TO WIRE THIS

GRIDDLE YOURSELF.

2. Remove the SPECTRUM Electric Griddle from the packaging. Be

certain that all protective plastics and residues are thoroughly

cleaned from its surface.

3. Place the SPECTRUM Electric Griddle on a rm level surface. Local

standards and regulations should be consulted in order to abide by

standards set in relation to positioning, spacing, and ventilation.

4. Proper connections and power supply are necessary for

satisfactory performance.

5. The external wiring must be in conduit or an approved type of

exible cable suitable for operation at temperature indicated at

the conduit hole, and in a proper size to carry the load.

6. The supply circuit must be correctly fused and equipped with a

means of disconnecting, as required by the local electrical code.

For griddle with plugs and leads set, simply provide a suitable

power point and connect.

THIS EQUIPMENT GETS EXTREMELY HOT.

CAUTION ATTENTION

Do not position or operate near combustible materials or

ammable objects.

Ne pas placer ni faire fonctionner l'appareil près de

matériels combustibles et d'objets inﬂammables.

Once your Griddle has been placed in position, be sure that the

stainless steel waste tray is correctly positioned.

Une fois que votre Plaque de Cuisson (Plancha) est mise en

place, veillez à ce que le bac à déchets en acier inoxydable

soit correctement placé.

Supply the appropriate power and connect to power source; your

Griddle is now ready to turn on and operate. (For power supply

please see technical specication sheet, page 1).

Fournir l'alimentation secteur appropriée et brancher

l’appareil à la source d'alimentation ; votre plaque

de cuisson est maintenant prête à être allumée et à

fonctionner. (Pour l’alimentation, veuillez voir la ﬁche

technique, page 1).

FEET

Install feet by screwing each foot into the threaded openings on the

bottom of the griddle. Failure to use feet will void warranty and could

cause unsafe conditions.

LEVELING

Level unit by adjusting the four feet and tighten securely. The adjustable

feet have an adjustment of one inch for lineup with other countertop

lines. Check the feet every 60 days to make sure they are tight.

ASSEMBLY

Take the catch tray and slide into the runners below the heating

elements and place into the rack. Once in position, the catch tray

will catch food product crumbs, grease or drippings.

COMMISSIONING

Commissioning of your new griddle is of the utmost importance.

Commissioning is the thorough and methodical testing of the equipment,

sub systems, and systems to make sure that the nal product functions

properly and safely at the work site. By identifying potential problems

(i.e.: equipment location, ventilation, local re/electrical codes,

installation, operator training and certication) before equipment is

placed into service, costly outages and potential damages can be avoided.

These instructions should be followed at all times. Failure to follow

these instructions could result in injury to yourself and others.

TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:

1. Read this manual thoroughly before installation and operation.

DO NOT proceed with installation and operation if you have any

questions or do not understand anything in this manual. Contact

your representative or the manufacturer rst.

Fire Hazard.

Correct installation precautions,

procedures and regulations

must be followed. Operation

and safety training is necessary

for all users of this equipment.

Risque d'incendie

La surchaue des vapeurs d'huile ou de

l'huile peut s'enammer et provoquer

un incendie. Surveillez la température,

la qualité et le niveau d’huile. Utilisez et

entretenez le système d'élimination des

vapeurs d'huile.

The equipment must be

installed by qualied personnel

only. Correct installation

precautions, procedures and

regulations must be followed

in order to reduce the risk of

re. Hood and re suppression

systems must be maintained

per manufacturer's guidelines.

Only qualied and trained

personnel are to use this

equipment.

Faire chauer l'huile avec précaution. Si

l'huile fume, réduire le feu. Ne pas laisser

l'appareil sans surveillance. Si le feu se

produit, éteindre l'appareil, couvrir jusqu'à

refroidissement. Ne pas mettre l'eau dans

l'huile chaude ou enammée. Ne faites pas

fonctionner avec de l'huile sous la barre

d'huile. L’huile sale a un point d'éclair

plus bas. Remplacer l'huile sur une base

régulière. Maintenir le niveau d'huile

correct. Utiliser un système d'évacuation

de la vapeur d'huile (capot) pour réduire

l'accumulation de graisse et d'huile sur les

surfaces de paroi ou de plafond.

WARNING AVERTISSEMENT

Electrical Shock Hazard

Keep water and other liquids

from entering the inside of the

unit. Liquid inside the unit could

cause an electrical shock.

Risque de choc électrique

Conserver l'eau et d'autres liquides

de pénétrer à l'intérieur de l'appareil.

Liquide à l'intérieur de l'appareil pourrait

provoquer un choc électrique.

Do not spray water or cleaning

products. Liquid could contact

the electrical components

and cause a short circuit or an

electrical shock. Do not use unit

if power cord is damaged or has

been modied.

Ne pas pulvériser de l'eau ou des produits

de nettoyage. Le liquide pourrait contacter

avec les composants électriques et causer

un court-circuit ou un choc électrique.

Ne pas utiliser l'appareil si le cordon

d'alimentation est endommagé.

ou a été modié.

WARNING AVERTISSEMENT

Operation

6. Remove the excess fat and wipe clean. Griddle surface is ready

for use.

NOTE

EVEN WITH CAREFUL SEASONING, FOOD CAN STICK TO

THE GRIDDLE COOKING SURFACE UNTIL GRIDDLE PLATE IS

“BROKEN IN”.

Before operating the griddle, it must be checked to see that it

is sitting level. Adjust the feet to level the griddle. Be sure the

catch tray has been assembled correctly (see image below).

Catch Tray

Rack

NOTE

Upon ﬁrst use, griddle can produce a burning metal smell.

This is normal and smell will decrease with use.

Season the surface

1. Clean griddle surface thoroughly. After griddle has been cleaned, it

must be seasoned to prevent food from sticking. Follow the steps

below for the correct heating method to season the griddle before

use and after scouring.

2. Switch to ON and adjust the thermostat dial knob to 350°F.

3. Use a clean cloth (not a spatula), to spread a thick lm of cooking

oil or fat over the griddle cooking surface. Film must remain on hot

griddle for 30 minutes.

CAUTION

GRIDDLE SURFACE WILL BE HOT

PLAQUE SURFACE SERA CHAUD

4. Remove the excess fat and wipe clean.

5. Apply another lm of cooking oil over hot cooking surface for

another 30 minutes.

Temperature Control

Your griddle should be turned on prior to usage to allow the cooking

surface to warm up; 5-7 minutes is sucient.

To get ecient use from this unit, it is recommended that for

intermittent use that the thermostat be turned down when not

cooking. This will assist in reducing power consumption and also allow

for quicker heat response when needed.

It is recommended that the cooking surface is lightly greased before

each use.

The temperature is thermostatically controlled.

Be sure On/Oﬀ switch is ON, for EDG-36, and adjust

temperature dial knob to the desired setting.

Power for EDG-24 is activated when temperature dial knob

is turned to desired heat setting.

The set point of each thermostat is marked on the front panel with

"TEMP " in the 9 o’clock position. Griddle is equipped with one

thermostat per various cooking surface segments.

For the 24” griddle, every 12” and for the 36” griddle, every 18”.

Cooking

Switch griddle to ON and adjust the thermostat dial knob to the

desired temperature. After a short pre-heating period, the thermostat

will automatically maintain the selected temperature. When the set

temperature is reached, the signal light will go OFF.

A temperature setting of between 375ºF and 430ºF will be sucient

for general cooking. This may vary for particular food types, individual

needs, or experience.

Simply place the food products on the grilling surface and cook to

manufacturer's specications.

TO AVOID SERIOUS PERSONAL INJURY:

• ALWAYS install equipment in an area with adequate light and space.

• ONLY operate on a solid, level, nonskid surface that is

nonammable and away from sinks and water hazards.

• NEVER bypass, alter or modify this equipment in any way from

its original condition. Doing so can create hazards and will

void warranty.

• NEVER operate the griddle without all warnings attached to it. Burn Hazard.

When in operation, the

Conveyor Toaster will be hot at

the entrance to the conveyor

cavity.

Please take extreme caution.

Risque de brûlure.

Ne touchez pas les surfaces chaudes ou

chauées liguid tout appareil chaue ou

en fonctionnement.

USE CAUTION WHEN

TOUCHING THE UNIT.

Ne touchez pas le liquide chaud

ou les surfaces de chauage

lorsque l’appareil chaue ou en

fonctionnement.

WARNING AVERTISSEMENT

HOT

To maintain the appearance and increase the service

life, clean your unit daily. The Electric Griddle should be

cleaned after each day’s operation; however, the unit may

require more frequent cleaning depending on the volume

of production.

Cleaning, Care & Maintenance

1. Switch power o and disconnect from the outlet before cleaning.

2. Allow the Electric Griddle to cool down after use before dismantling

for cleaning; the unit will still be too hot to handle immediately

after use. Regular cleaning will result in easier cleaning, as the build

up will be less. Correct preparation of the cooking surface when rst

used will assist in keeping the plates clean.

3. For best results clean the plate while still warm using warm soapy

water. A nylon cleaning cloth may be used. It is recommended that

you avoid scrapers made from steel wool, as they will damage the

plate. Do not use cold water on warm plates, as buckling eect

may occur.

4. When scrubbing the plates, do not clean too thoroughly; if you do,

you must prepare the cooking surface again before use.

5. Remove catch tray from unit and discard waste; clean with hot

soapy water.

6. The remainder of the Electric Griddle can be cleaned with a

damp cloth using warm, soapy water. Warm, soapy water is

recommended for cleaning; prolonged use of cleaning agents may

cause damage to stainless steel.

7. Do not immerse completely in water or use hose to clean.

RECOMMENDED CLEANING

It takes very little time and eort to keep the griddle attractive and performing at top eciency. If grease is allowed to accumulate, it will form a

gummy cake and then carbonize into a hard substance that is extremely dicult to remove. To prevent this condition, please follow the cleaning

steps below:

PART REQUIRED ACTION FREQUENCY

Scraping Scrape the griddle with a scraper or exible spatula to remove excess fat and food. A catch tray is provided

for the scrappings.

If there is an accumulation of burned fat and food, griddle must be thoroughly scoured and re-seasoned.

While the griddle is warm, use pumice or griddle stone to remove excess fat and food. Do not use steel

wool because of the danger of steel slivers getting into the food.

After Each Use

Body Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of griddle.

Wipe the polished areas with a soft cloth.

Daily

Controls Griddle must be turned OFF when not in use.

Switch griddle to OFF to disconnect power supply from griddle.

Use a clean cloth to wipe down switches and thermostat dial knobs.

Daily

Catch tray Once griddle has cooled, remove catch tray from griddle and discard the waste, debris and crumbs.

CAUTION: If catch tray is permitted to ll too high, the excess grease will run out of the overow hole at

the front of catch tray.

The catch tray is removed by pulling forward. USE CAUTION WHEN FILLED WITH HOT GREASE!

Per Use

or at least Daily

Burn Hazard.

When in operation, the

Conveyor Toaster will be hot at

the entrance to the conveyor

cavity.

Please take extreme caution.

Risque de brûlure.

Ne touchez pas les surfaces chaudes ou

chauées liguid tout appareil chaue ou

en fonctionnement.

USE CAUTION WHEN

TOUCHING THE UNIT.

Ne touchez pas le liquide chaud

ou les surfaces de chauage

lorsque l’appareil chaue ou en

fonctionnement.

WARNING AVERTISSEMENT

HOT

Electrical Shock Hazard

Keep water and other liquids

from entering the inside of the

unit. Liquid inside the unit could

cause an electrical shock.

Risque de choc électrique

Conserver l'eau et d'autres liquides

de pénétrer à l'intérieur de l'appareil.

Liquide à l'intérieur de l'appareil pourrait

provoquer un choc électrique.

Do not spray water or cleaning

products. Liquid could contact

the electrical components

and cause a short circuit or an

electrical shock. Do not use unit

if power cord is damaged or has

been modied.

Ne pas pulvériser de l'eau ou des produits

de nettoyage. Le liquide pourrait contacter

avec les composants électriques et causer

un court-circuit ou un choc électrique.

Ne pas utiliser l'appareil si le cordon

d'alimentation est endommagé.

ou a été modié.

WARNING AVERTISSEMENT

If your SPECTRUM Electric Griddle does not operate, please check the following before placing a service call.

Please ensure:

• There is correct power supply.

• Breaker is checked.

• The machine is plugged in correctly and power is switched on.

• The timer and thermostat are in the correct position.

• The elements are clear of any food particles.

Troubleshooting

ISSUE MIGHT BE CAUSED BY RECOMMENDED SOLUTION

The unit is not working

Power supply Check power source

Power switch has not been turned on Check that the unit is correctly plugged in and

turned on

Plug/cord, set or external wiring is damaged Call WINCO to make service arrangements through

its Service Provider Network

Internal wiring fault Call WINCO to make service arrangements through

its Service Provider Network

The indicator light is on, but

griddle is not heating up

Faulty elements Call WINCO to make service arrangements through

its Service Provider Network

Operation of thermostat

All thermostats are not turned on

Make sure thermostat is set correctly and make sure

dial is not spinning on the thermostat, giving the

wrong reading

Faulty thermostat Call WINCO to make service arrangements through

its Service Provider Network

The indicator light is NOT on, but

the griddle IS heating up

Faulty indicator light Call WINCO to make service arrangements through

its Service Provider Network

Cooking Surface is heating up

slowly

Carbon build up Make sure that the plates are kept clean and free

from carbon build up/debris

Thermostat setting Make sure thermostat is set correctly and make sure

dial is not spinning on the thermostat, giving the

wrong reading

Faulty elements Call WINCO to make service arrangements through

its Service Provider Network

Food Sticking

Carbon build up Make sure that the plates are kept clean and free

from carbon build up/debris

Not seasoned Season grill, see Operating Instructions, page 5

Service and Repair

There are no user serviceable parts within this appliance.

To avoid serious injury or damage, never attempt to repair the unit

or replace a damaged power cord yourself.

DO NOT send unit to WINCO without rst contacting our customer

service department.

See "Limited Warranty" section on page 11 for details.

Safety

A WINCO Approved Service Technician should carry out repairs if

necessary. Do not remove any components or service panels on this

product. Allow the griddle to cool down after use before dismantling

for cleaning; the unit will be too hot to handle immediately after use.

Switch o power and disconnect from the outlet before cleaning.

Do not immerse unit in water or use hose to clean.

Ne pas immerger l'appareil dans l'eau ni utilisez un jet d'eau pour

le nettoyer.

If the power cord is damaged, it must be replaced by a WINCO

Approved Qualied Service Technician in order to avoid a hazard.

Exploded View & Spare Parts List

MODEL EGD36

Model EGD-36

No. Description Part # QTY

1 Griddle Plates Assy EGD-36-P1 1

2 Heating Element EGD-36-P2 2

3 Hardware Assembly EGD-36-P3 2

4 Insulation EGD-36-P4 2

5 Insulation Plates EGD-36-P5 1

Ceramic

Connector - 1

EGD-36-P6 2

Ceramic

Connector - 2

EGD-36-P7 2

7 Plug & Lead EGD-36-P8 1

8 Feet EGD-36-P9 4

9 Base Board EGD-36-P10 1

10 Thermostat EGD-36-P11 2

11 Dial EGD-36-P12 2

12 Indicator Light EGD-36-P13 2

13 On/O Switch EGD-36-P14 2

14 Drip Tray EGD-36-P15 1

15 Main Body Assy EGD-36-P16 1

Exploded View & Spare Parts List

Model EGD-24

No. Description Part # QTY

1 Feet EGD-24-P1 1

2 Set Square EGD-24-P2 2

3 Drip Tray EGD-24-P3 2

4 Base Board EGD-24-P4 1

5 Indicator Light EGD-24-P5 1

6 Dial EGD-24-P6 4

7 On/O Switch EGD-24-P7 1

8 Thermostat EGD-24-P8 4

9 Main Body Assy EGD-24-P9 1

10 Insulation Plates EGD-24-P10 2

11 Insulation EGD-24-P11 2

12 Hardware Assembly EGD-24-P12 2

13 Heating Element EGD-24-P13 2

14 Griddle Plates Assy EGD-24-P14 1

15 Plug & Lead EGD-24-P15 2

16 Connection Box EGD-24-P16 2

17 Connector Bar EGD-24-P17 2

18 Connection

Box Cover

EGD-24-P18 1

MODEL EGD24

NOTE:

1) FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY,

SUITABLE FOR AT LEAST 194°F (90°C). USE WIRE GAUGE

SHOWN OR LARGER

2) ALL INTERNAL WIRING IS #14 GA

SINGLE PHASE CONNECTION

3 PHASE CONNECTION

THERMOSTAT 2THERMOSTAT 1

PILOT LIGHT 1 PILOT LIGHT 2

ON/OFF SWITCH 1

3 PHASE CONNECTION

SINGLE PHASE CONNECTION

ON/OFF SWITCH 2

ON/OFF SWITCH 3

ON/OFF SWITCH 2

HEATING ELEMENTS 1 HEATING ELEMENTS 2

THERMOSTAT 2 THERMOSTAT 3THERMOSTAT 1

PILOT LIGHT 2 PILOT LIGHT 3PILOT LIGHT 1

HEATING ELEMENTS 1 HEATING ELEMENTS 2 HEATING ELEMENTS 3

NOTE:

1) FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY,

SUITABLE FOR AT LEAST 194°F (90°C). USE WIRE GAUGE

SHOWN OR LARGER

2) ALL INTERNAL WIRING IS #14 GA

Electrical Diagram The circuit diagrams are provided to assist qualied technicians. Only SPECTRUM agents or Recommended Qualied Technicians

should carry out repairs if needed. (Refer to page 11 for service arrangements)

DO NOT remove any components or service panels on this product.

EGD-24

EGD-36

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Spectrum Bratpfanne Handbücher

Spectrum

Spectrum Winco EGD-24M Beilage

Beliebte Bratpfanne Handbücher anderer Marken

Proctor-Silex

Proctor-Silex 25340 Bedienungsanleitung

New House Kitchen

New House Kitchen NH33-C Bedienungsanleitung

Magikitch'n

Magikitch'n 24 Bedienungsanleitung

Black Stone

Black Stone 1650 Bedienungsanleitung

Anvil

Anvil FTA7116 Bedienungsanleitung

Presto

Presto 07030 Bedienungsanleitung

Pit Boss

Pit Boss PB2BGT1 Handbuch

Dyna-Glo

Dyna-Glo DGL260SNP Bedienungsanleitung

Char-Broil

Char-Broil 19952085 Bedienungsanleitung

APW Wyott

APW Wyott HMG-2424 Bedienungsanleitung

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Bedienungsanleitung

Airxcel

Airxcel Suburban Elite SOP-1005A Bedienungsanleitung

Keating Of Chicago

Keating Of Chicago MIRACLEAN PRE-2000 Bedienungsanleitung

Nexgrill

Nexgrill 720-0786A Bedienungsanleitung

Outwell

Outwell FH-3047C Bedienungsanleitung

Rankam

Rankam Member's Mark GR2298901-MM-02 Kurzanleitung

Black Stone

Black Stone 1972 Bedienungsanleitung

Star

Star Ultra Max 760TA Bedienungsanleitung