SPL-Technik SPL 180 Bedienungsanleitung
RUS
SPL 180
Three channel, dual propeller helicopter with infrared
controls. Military series.
User’s Manual
3-Kanal-Doppel-Rotor Hubschrauber mit IR-Steuerung.
Military Edition.
Bedienungsanleitung
Hélicoptère à double rotor et à trois canaux de com-
mande infrarouge. Série militaire.
Manuel d'utilisation
Elicottero comandato a infrarossi a tre canali con doppia
elica. Serie militare.
Manuale di istruzioni
Трехканальный двухвинтовой вертолет на
ИК-управлении. Военная серия.
Руководство по эксплуатации
ENGDEFRIT
SPL-Technik
2
Length: 230 mm
Width: 85 mm
Height: 95 mm
Diameter of the main rotor: 190 mm
Weight: 38 g
Helicopter battery: LiPo 3.7V 160mAh
Elements of transmitter power supply: 6AAx1,5V batteries (not
included)
Time to fully charge: 30 min.
Flight time: 6-8 min.
Operational radius of the device: up to 10 metres.
ENG
User’s Manual
Please read these instructions before using the model. Use the
model only in accordance with these instructions.
Three channel, dual propeller helicopter with infrared controls.
Military series
- 3 control channels
- Battery charges from an USB-port
- Built-in gyroscope
- Excellent stability and amazing maneuverability
- Model for flights in a closed space
- Includes spare parts
The helicopter has three control channels. It can fly up and down, forward and
back. The gyroscope allows it to turn around its axis with high precision.
Basic technical parameters of the helicopter:
3
Kit includes:
- Helicopter: 1 pce.;
- Transmitter with charge function: 1 pce.;
- Instructions: 1 pce.;
- USB charger cable: 1 pce.;
- Spare blades: 2 pces.;
- Spare rear propeller: 1 pce.;
- Screwdriver: 1 pce.;
ENG
SPL 180
Three channel, dual propeller helicopter with infrared
controls. Military series.
User’s Manual
3-Kanal-Doppel-Rotor Hubschrauber mit IR-Steuerung.
Military Edition.
Bedienungsanleitung
Hélicoptère à double rotor et à trois canaux de
commande infrarouge. Série militaire.
Manuel d'utilisation
Elicottero comandato a infrarossi a tre canali con doppia
elica. Serie militare.
Manuale di istruzioni
Трехканальный двухвинтовой вертолет на ИК
управлении. Военная серия.
Руководство по эксплуатации
ENGDEFRITRUS
SPL-Technik
Kit elements
Safety rules
Stabilizer
Main rotor
Main rotor
Tail rotor
Chassis
Power switch of the helicopter
Charger socket
Charging cable
Power
indicator
Demo flight button
Gas stick
Channel switch
Infrared receiver
On/Off switch
Accelerator
Trimmer
Control stick of main rotor
Charge indicator
USB charger cable Instructions
1. Use baeries with voltage not less than 1.5 V. Low grade power supply elements
significantly reduce the device’s operaonal range.
2. Keep the model and its components away from moisture. This can cause damage to
the electronics.
3. Before each flight, check the operaonal range of the device. Be sure that the model’s
baery is fully charged and that the transmier has fresh AA baeries.
When cleaning the model, do not use solvents. This can cause damage to the plasc parts
of the model.
4
ENG
Safety rules
Parts of the helicopter’s power supply
1. Helicopter baery {installed on board) – 3.7V 160mAh
2. Power supply parts of the transmier: 6 АА 1.5V baeries (not included).
4. When cleaning the model, do not use solvents. This can cause damage to the plasc
parts of the model.
5. It is recommended that you fly the model in spacious premises. This model is not
intended for flying outdoors.
6. Do not fly the model in places where people, especially children, are gathered, and
stay at least 15 metres away from devices which could interfere with the flight of the
model. Make sure that there are no foreign objects with which the model could collide.
7. Don’t let the model fly too far away from you. The farther away it is, the more difficult
it is for you to correctly judge its posion and behavior in flight.
8. Always point the opcal sensors of the transmier directly at the model.
9. Powerful sources of light, sources of infrared (IR) radiaon and sunlight can substan-
ally influence the quality of the signal received from the IR transmier. Do not send the
model flying in the direcon of the aforemenoned interference. Before each flight, be
certain there is no interference present.
10. When learning how to fly, it is recommended that you make flights at low altude. In
case of pilot error, you can then easily reduce the gas and lessen the risk of serious
damage to the model.
11. In case of unforeseen emergencies or collision with some obstacle, immediately
switch off the engine. Never turn on the model if something obstructs the rotaon of the
rotors.
12. Minimum dimensions of the premises used for flying: 5x5x3 metres, without any
draughts and direconal air flows.
13. Take off only from a flat and smooth surface, starng out slowly and gradually raising
the rpms of engine.
14. Never hold the model with rotang rotors at the level of your face.
15. Always look at the model; don’t concentrate aenon on the transmier.
16. Don’t stand behind objects which could prevent you from quickly going up to the
model.
17. Watch closely the direcon and height of the flight; always compensate for any
deviaon from the intended direcon of flight by small and steady movement of the
transmier scks. The main error of beginning pilots is jerky movement of the scks in
extreme posions – this always leads to loss of control and to the model’s falling down.
18. Trim the model before each flight.
19. Never grab the model by rotor parts.
20. Always switch off the model’s power, even if the rotors have stopped automacally.
21. Never close and do not tape down the transmier emier.
22. Never tape onto the model addional parts or sckers.
23. Don’t let children start up the model without adult supervision.
24. Never start up the model if it has damaged parts.
25. Do not disassemble and do not make alteraons in the model’s construcon.
5
ENG
Installation of the transmitter batteries
Charging the helicopter
1. Open the lid of the baery compartment, put in place the б AA baeries
(not included in kit), being sure that the polarity is correctly aligned.
2. Close the lid of the baery compartment.
Turn the power supply switch of the helicopter to the OFF posion.
Charging method А: remove the charging cable from the transmier compartment and
connect it to the charging socket of the helicopter. The helicopter and transmier must be
switched off. Next turn on the transmier; now the green and red indicators of the
transmier will be illuminated. The charging me is 30 minutes. When the baery is fully
charged, the green light will turn off and the red indicator will flicker. Your helicopter is
now ready to fly.
Charging method В: connect the USB-charger cable to the USB-port of a computer. A red
light on the plug will switch on. Connect the cable with the helicopter’s charger socket;
now the light on the plug will switch off. The helicopter should be switched off. The
charging me is 30 minutes. When the baery is fully charged, the light on the socket will
again turn on. Your helicopter is ready to fly.
The model helicopter is equipped with an in-built lithium polymer baery. When using
it, you must observe the following safety rules:
1. Don’t let the baeries fall from heights.
2. Don’t expose the baeries to blows on hard surfaces.
3. Don’t throw the baeries into a fire or into water and store them in a dry place.
4. Use only the original charging device.
5. Don’t disassemble the baery.
6. Don’t leave the baery unsupervised when charging.
A. From the transmitter В. From a computer
6
ENG
Preparation for flight
Flight and manoeuvres
1. Charge the model and insert fresh
baeries in the transmier.
2. Turn on the power of the transmier.
3. Move the helicopter’s power switch to
the ON posion. The indicator on board
the helicopter should flicker brightly.
4. Place the helicopter on an even
surface in front of you.
5. Be sure that the distance between
you and the helicopter is around 2 metres.
6. Wait unl the indicator on the model
stops flickering. Now you can take off smoothly
by moving the gas sck upwards.
Up
Down
Forward
Back
Turn to the
right
Turn to the
le
Demo mode
Controlling
the
accelerator
Smoothly move the le sck upwards
(away from yourself)
Smoothly move the le sck back
(towards yourself)
Smoothly move the right sck forward
(away from yourself)
Smoothly move the right sck back
(towards yourself)
Smoothly move the right sck to the right.
Smoothly move the right sck to the le.
When you depress the demo flight buon,
the demo mode is switched on. You just have
to control the gas and the helicopter flies
automacally.
To switch the accelerator funcon on
or off, press the buon on the right
side of the transmier. In acceleraon
mode, the helicopter accelerates to
maximum speed.
Important: only small and smooth changes in the position of
the sticks ensure stable flight of the helicopter.
7
ENG
Flight practice
Important: if the helicopter is always rotating, please use
the trimmer to adjust the rudder.
If the helicopter rotates during flight, follow the instrucons below to stop the rotaon.
Adjust the trimmer unl the helicopter stops rotang.
Adjust the trimmer unl the helicopter stops rotang.
Hovering is when the helicopter maintains an unchanged posion in the air. This
manoeuvre must be mastered well.
Slowly raise the helicopter to a height of 30-40 cm. If the model is moving in one
direcon or another, carefully move the respecve control sck in the direcon opposite
to the direcon of the model so as to return the helicopter to the starng posion.
Draw a circle on the floor and try to keep the helicopter inside this circle. Once you
have mastered hovering in place, move on to execung figures. Begin by flying a square
route: a ‘box’. Then do a figure-eight as shown in the illustraons. As soon as you master
these manoeuvres, try to repeat them in the reverse direcon.
The helicopter rotates counter clockwise.
The helicopter rotates clockwise.
Turn the trimmer clockwise.
Turn the trimmer counter clockwise.
8
ENG
Flight practice
Landing
ATTENTION!
Perform hovering, then smoothly reduce the rotaon of the rotors. The model will
begin to descend. Don’t cut the rotaons too sharply, because if the rotors stop the model
will inevitably fall to the ground. This can result in damage to the model.
If the helicopter baery is discharged or the helicopter is used for a long me, the
power can automacally cut off. When this happens, the indicator on board the helicop-
ter twinkles and the helicopter is inacve. This is a normal occurrence with this model.
In case of automac power cut-off due to lengthy use of the helicopter, move the gas
sck to the minimum posion, switch off the helicopter’s power, charge the on-board
baery and then switch on again: your helicopter will again be ready to fly. Aenon! If
the gas sck is not in the minimum posion, then the helicopter will immediately take off.
The flickering red indicator on the helicopter’s control board tells you the transmier
baeries are low. Change the baeries and resume flying.
9
ENG
Possible failures and methods for correcting them
The manufacturer reserves the right to change the instrucons, the kit elements and the operang
specificaons without advance warning. Depending on a specific shipment, items may differ
slightly from what is described in the instrucons.
Problem
Transmier
indicator
is not
illuminated
Model does
not react
to the
transmier
signal
Model does
not gain
altude
Possible cause
Power switch is in the OFF posion.
Baeries have been inserted without
aenon paid to the polarity.
Baeries are insufficiently charged.
Infrared light beam from the
transmier is not reaching the
model’s receiver.
Powerful light sources, sources of
infrared radiaon and sunlight impair
the quality of the IR signal
Rotaon speed of the rotors is
not sufficient.
Model is not sufficiently charged.
Soluon
Put the power switch in the
ON posion.
Pay aenon to polarity when
you reinsert the baeries.
Replace or charge the baeries.
Reduce the distance between
the model and the transmier,
be certain that there is no
interference disturbing the signal.
Check to see there is no
interference or choose other
premises for the flights.
Increase the rotor rotaon by
smoothly moving the gas sck.
Fully charge the model’s baery
in accordance with the
instrucons.
Inhaltsverzeichnis
Sprachen:
Andere SPL-Technik Drohne Handbücher
