Spod BantamX Technisches Datenblatt
R
GET TO KNOW YOUR
Positive battery cable connection
DIP switches
Negative battery cable connection
Mounting plate
Accessories terminal block for switches 5-8
Input terminal block
Jumper for input polarity selection
Controller inputs (Ethernet cable)
2AMP fuse for circuit board protection
Cover. Do NOT remove or warranty will be voided
Accessories terminal block for switches 1-4
Reverse polarity warning lights (lights red if reverse polarity is detected
Thumb screw for fastening lid
Place holders for switch ID labels (legends)
Auxiliary port identifcations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
COMPONENTS
12 3
4
5
6789
10
11
12
13 14
15
DIP SWITCH
1
2
3
4
5
6
USE / DESCRIPTION
Three purposes:
1) Initialize “pairing mode” for Bluetooth applications.
2) Disable deep sleep mode.
3) Troubleshooting.
Change between 12V (OFF position) and 24V (ON
position) electrical systems.
Key-on lock-out control. ON position allows switch #1 to
only be active when the ignition is on.
Key-on lock-out control. ON position allows switch #2 to
only be active when the ignition is on.
Multiple Source select. Used to identify Bantam.
Multiple Source select. Used to identify Bantam.
DIP SWITCH SETTINGS 1 2 3 4 5 6
OFF
ON
FACTORY DEFAULT SETTINGS
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
1 2 3 4 5 6
ON
OFF
12V 24V
SWITCH #1
ACTIVATED
SWITCH #2
ACTIVATED
SWITCHES #1 & #2
ACTIVATED
BANTAM #1 BANTAM #2
BANTAM #3 BANTAM #4
INPUT 1
INPUT 2
INPUT 3-10
Disable low voltage cut o by attaching 12/24V from a positive
power feed.
Activate key-on / lock-out function from a source of 12/24V
from a positive power feed, such as a fuse or circuit that is live
when the ignition key is on. WARNING: To avoid a short, always
attach to input rst, power last.
Activate any of the switches (1-8) by an external device that has
a 3.3 - 24VDC signal.
Use the jumper to switch the 8 inputs between Positive trigger input and
Ground trigger input. NOTE: this will apply to all 8 inputs.
INPUT FOR SWITCH 8
INPUT FOR SWITCH 7
INPUT FOR SWITCH 6
INPUT FOR SWITCH 5
INPUT FOR SWITCH 4
INPUT FOR SWITCH 3
INPUT FOR SWITCH 2
INPUT FOR SWITCH 1
LOCK-OUT 12/24V POWER INPUT
LOW VOLTAGE CUT OFF BYPASS
INPUT TERMINAL BLOCK
+ / - TRIGGER INPUTS
GROUND TRIGGER: 2 PINS ON THE LEFT POSITIVE TRIGGER: 2 PINS ON THE RIGHT
INSERT WIRE AND TIGHTEN
USING A MINI
FLATHEAD SCREWDRIVER
WARNING: Always attach to
input terminal block first before
attaching to the power side.
10
9
8
7
6
5
4
3
2
1
10
9
8
7
6
5
4
3
2
1
1 2 3 4 5 6
OFF
ON
1 2 3 4 5 6
OFF
ON
Download the sPOD Bantam app onto your
smartphone or tablet. Be sure that your
device’s Bluetooth option is turned on.
With the app closed and o, ip DIP switch 1
ON then OFF in quick succession to put the
Bantam in PAIRING MODE for 60 seconds.
Open the Bantam app and touch Setup.
Touch the Scan button and wait 10 seconds.
Hit Cancel and wait about 10 seconds for the
PIN to appear in upper left (in white). Touch
the Setup button.
Touch the Scan button and wait 10 seconds.
When Pairing Request dialogue box appears,
enter PIN number and then touch the Pair
button. The app will now be paired to the
Bantam and will be ready to use.
To reset pairing with all devices, turn DIP
switch #1 ON and OFF 5 times quickly.
PAIRING THE BLUETOOTH
R
INSTRUCTIONAL VIDEOS ALSO AVAILABLE ON OUR WEBSITE
Inhaltsverzeichnis
Andere Spod Automobilelektronik Handbücher
