Sport-thieme 201 0915 Bedienungsanleitung

Sport-Thieme®

Handball Goal, 3x2 m,

Free-Standing or socketed

Art.-Nr.: 201 0915

203 4502

Assembly instructions

D-38367 Grasleben ·Germany

sport-thieme.com · info @sport-thieme.com

Phone: +49 53 57 181 543 · Fax: +49 53 57 181 921

Assembly instructions for Art.-Nr. 201 0915/203 4502

1. Scope of delivery

Please check the following content before assembly.

The following indicated quantities refer to 1 Handball goal. In case of a delivery in pairs we double the

amount correspondingly. Pictured colours of proles are only samples and may dier from delivered proles.

1x Galvanized steel ground tube Ø ¾“

1x Crossbar, prole 80 x 80mm

2x Uprights, prole 80 x 80mm

1x Hexagon screwdriver SW6, DIN 911, length approx.

470mm (only for goal in ground sockets)

2x Rigid net hoop 2x Steel corner joint

8x Steel plate

2x Upright cap

Accessories

Only for catalogue no. 2034502 –

goal in ground sockets:

2x Ground socket, length 300 mm

2x Cap for ground socket

Accessories:

32x Net holder

2x Bushes with thread M8, of aluminium round tube 20 x 5

mm, length 40 mm

6x Plastic holder

8x Safety hexagon screw M8 x 50mm, DIN 931

8x Safety hexagon socket cylinder screw M8 x 14mm, DIN 912

2x Hexagon screw M8 x 90, DIN 931

2x Hexagon screw M8 x 12, DIN 933

10x Self-locking nut M8, DIN 985

4x Self-locking cap nut M8, DIN 986

4x Ring nut M8 x 50

8x Plug pin

1x Hexagon screwdriver SW5, DIN 911, black

1x Hexagon screwdriver SW6, DIN 911, length 120 mm

1x Assembly instruction

Assembly instructions for Art.-Nr. 201 0915/203 4502

2. Assembly of the goal

The following tools are necessary:

- 2 wrench/ring spanners 13 mm

- 1 mallet/hammer

- 1 drill Ø 1.5 mm

- 1 thin screw driver (for net hook xing, if necessary)

a) Assembly of crossbar/uprights:

Lay crossbar and uprights on the ground, groove facing upwards and mitres joining. Stick 4 steel plates on steel corner joint (see

1st picture bottom left). Then stick crossbar and upright on steel corner joint (see other bottom pictures).

b) Assembly of net hoops:

Place rigid net hoops on the right and left side of crossbar/upright construction. Fixing of net hoop at the top: Screw 4 hexagon

socket screws M8 x 50, DIN 931 into the steel corner joint (see picture bottom left).

Assembly instructions for Art.-Nr. 201 0915/203 4502

c) Assembly of net hoop at the bottom- goal free standing, cat. No. 2010915:

Screw from upright’s inside 4 hexagon socket cylinder screws M8 x 14mm, DIN 912 in the bottom end of the upright with

extended hexagon screwdriver SW6, length 120 mm. Fix from the outside 4 nuts M8, DIN 934 (see 1nd to 3th bottom pictures).

Then adjust net hoops at the top and at the bottom and tighten all screws.

Assembly of net hoops at the bottom - goal in ground sockets, cat. no. 2034502:

The assembly is done as described above but with extended hexagon screwdriver SW6, length approx. 470 mm (see the following

pictures).

Assembly instructions for Art.-Nr. 201 0915/203 4502

d) Assembly of caps:

Stick caps in the open ends of uprights (see picture bottom left). Bore them with drill 1.5 mm through the holes provided in the

uprights. Then x plug pins with a hammer/mallet (see picture bottom right).

e) Assembly of ring nut:

Stick from the inside ring nuts M8 x 50 through lateral and upper net hoop holes and x them with cap nuts M8, DIN 986 (see

bottom picture).

f) Assembly of ground tube:

Stick hexagon screw DIN 931, M8 x 90 through bush of aluminium tube (see picture bottom left). Then push bush into the ground

tube (see picture bottom mid) and screw hexagon screw DIN 933, M8 x 12 through holes of bush and ground tube. Tighten screw

(see picture bottom right).

Assembly instructions for Art.-Nr. 201 0915/203 4502

Fix ground tube between the net hoops (see 1nd picture bottom left). Screw 1 self-locking nut M8, DIN 985 so that the nut outside

is flush with the screw of the bush (see picture bottom right).

Then unscrew hexagon screw at the ground tube. Finally push screw with self-locking nut completely into the ground tube so that

the nut is directly xed on the net hoop (see pictures bottom left and right). Then tighten all screws and nuts.

Assembly instructions for Art.-Nr. 201 0915/203 4502

3. Assembly of the net

a) The net is not part of the delivery.

Fix net holders at the net rope. Bend open net holders a little and press rope into the holders. We recommend the following

distribution of net holders:

crossbar : 16 pieces

uprights : 8 pieces each

After having mounted all net holders x net at the goal construction. Erect the goal. Stick net holders in the net hook rail and x

them with a 90 degrees’ rotation. Use a thin screw driver if necessary (please avoid damages at the goal).

Fix net with plastic holders in the bottom part of net hoops. Cut o protruding ends of plastic holders (see picture bottom right).

b) Fix ends of upper and lower tensioning rope at the mounted ring nuts. Cut o protruding rope ends (see bottom picture).

c) Dismantling of the net is also done by rotation of the net holders through 90 degrees. Use again a thin screw driver if necessary.

Assembly instructions for Art.-Nr. 201 0915/203 4502

4. Assembly of the ground sockets

a) For handball gates with a size of 3,00 x 2,00 m the distance of the ground sockets must be 3,08 m (middle socket – middle

socket = center distance).

b) Concrete ground sockets according to the sketch. Foundation dimensions: 800 x 800 x 800 mm.

c) Do not apply an acceleration mixture or antifreeze during as these adhesives may cause damages to the ground sockets.

d) After hardening of the concrete, the goal can be inserted into the sockets.

5. Maintenance, safety and storage instructions

This goal is only constructed for Handball and not for other purposes. Check all screwed fas-

tenings before use and repeat it from time to time. It has to be protected against overturning at

any time.

Do not climb net or goal frame. It is not allowed to x additional parts or extensions at the goal

frame which may impair the safety of the goal (according to EN 749).

Check screwed fastenings regularly and change damaged and wearing parts if need be. The unit should be maintained once a

year by skilled personnel.

Notice: Due to our continuous quality check of products and

equipment technical modications are possible.

To avoid damage and misuse goals have to be stored secured and in an upright position when not in use.

Andere Handbücher für 201 0915

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sport-thieme Videospielzubehör Handbücher

Sport-thieme

Sport-thieme 11 203 3004 Montageanleitung

Beliebte Videospielzubehör Handbücher anderer Marken

VENOM

VENOM VS3057 Bedienungsanleitung

LINK-MI

LINK-MI HDVC01 Bedienungsanleitung

Thrustmaster

Thrustmaster T60 Bedienungsanleitung

Avermedia

Avermedia C875 Bedienungsanleitung

VENOM

VENOM VS2728 Bedienungsanleitung

DGT

DGT 960 Bedienungsanleitung

Sega

Sega Visual Memory Unit Bedienungsanleitung

Datel

Datel Go-tcha Expedition Bedienungsanleitung

TruGolf

TruGolf TruFlight 2 Bedienungsanleitung

CH Products

CH Products CH PRO THROTTLE Bedienungsanleitung

Thrustmaster

Thrustmaster T2PA Bedienungsanleitung

Cube Controls

Cube Controls Mercedes-AMG - GT Edition SIM Wheel Bedienungsanleitung

Hoffmann

Hoffmann Club Pro Bedienungsanleitung

ardistel

ardistel ADT SpeedRacer Bedienungsanleitung

Sven

Sven GC-W150 Bedienungsanleitung

Deltaco Gaming

Deltaco Gaming GAM-131 Bedienungsanleitung

Huffy

Huffy M731324 Bedienungsanleitung

Ace Bayou

Ace Bayou X Rocker Bedienungsanleitung