Sprintis 150DH Bedienungsanleitung
150DH
+++++++ Complete Manual - English +++++++
www.sprintis.eu
Hand held crimp sealers
Manual
2 3
Thank you for purchasing the hand held crimp
sealer 150DH.
Please read this instruction carefully before
use.
Please keep this manual on file as reference
book and for troubleshooting.
Please read before use
Content
Safety advice & helpful information ............... S. 3
Construction diagram ..................................... S. 4
Parts list ............................................................S. 5
Benefits & electric connection diagram .........S. 7
Operating instructions .....................................S. 8
Safety advice
Helpful information
To prevent damage of the device and inju- ries of the operator, it is absolutely neces- sary to
comply the safety notes in this manual.
The mentioned warnings describe possible injuries and damages, which are due to wrong
usage or maintenance of the device.
Please read and follow these safety notes before reading the manual.
CAUTION:
1) To reduce the risk of shock, disconnect
the unit from the supply circuit before
servicing the replacement of the heating
element.
2) To provide continued protection against
risk of electric shock, connect to properly
grounded outlet only.
3) If the supply cord is damaged, it must
be replaced by a special cord or
assembly available from the manufac
ture or its service agent.
WARNING:
1) A live heating element is located in the
jaw under the PTFE cloth. Use caution
during operation.
DO NOT TOUCH THE ELEMENT!
2) For continued protection against fire or
electric shock, replace only with type
cartridge and suitable ampere fuse,
provided in legible adjacent to fuse holder.
3) Close supervision is required when the
product is used near children.
1) Always keep the sealing platform clean. Particular care „should“ be taken to remove any
redidue from the Seal Jaws.
2) Do not clean the sealing platform with anything wet.
3) Occasionally check the condition both sides of the heater jaws. a poor sealer platform will
effect the quality of your seal.
4) Never touch to heater jaws for high temperature.
5) USE ONLY GENUINE REPLACEMENT PARTS.
Content, safety advice & helpful information
4 5
Construction diagram and parts list
Parts listConstruction diagram
17
5
2
10
12
14
15
16
13 18
17
11
3
9
46 8
No Description Parts-
No
No Description Parts-
No
1 Upper Lever Body 1A10-
7006
10 Return Spring 1E10-
7005
2 Lower Lever Body 1A10-
7007
11 Power Plug 1E30-
1005
3 Upper Sealer Jaw 2B40-
7001
12 Fixed Plates for
Heater
1C40-
7006
4 Ceramic Pads 1J40-
7001
13 Metal Plate for
Protection
1C10-
7004
5 Clips for Sealer
Jaw
1C40-
7005
14 Sealer PTFE Cloth 1J50-
3115
6 Bolt Pin & Screw 1D20-
7005
15 Sealer Rubber 1G20-
1010
7 Power Indication
Lamp
1E40-
7005
16 Rubber Holder 1C10-
7005
8 Temp. Controller
& Switch
1E60-
7005
17 Lead Wire 1E30-
7002
9 Heater 1E60-
7005
18 Fiber Washer 1J30-
7002
6 7
Benefits, electric connection diagram and operating instructions
1) constant heat for Cellophane & Foil
2) covered two 12 mm wide heated Jaws for Cellophane, Wax Paper, Foils, Alluminium-
Laminates and Heat Seal-able Labels.
3) light weight and easy to grip
4) equipped with temperature controller and working light
5) PTFE coated Seal Jaws
6) vertical line embossed seal
7) the power cord length is 3.0 meter
8) aluminium mesh safety guard
1) Connect power supply plug to AC outlet, the Power light appears indicating power to the
unit.
2) Turn on main temperature knob. Heating light appears, adjust the temp. control knob to the
100°C suitable scale fo thickness and material of bag. The heating light will go off about
three minutes, it is the heating time.
3) Adjust the temperature knob to suitable scale for sealing material.
4) Insert bag into the seal jaws and apply squeeze the lever handle to seal the bag.
5) Release the handle and remove the sealed bag.
6) If it does no complete with the seal, turn the temp. knob add until you get desired seal.
7) Turn off machine when not in use. Allow the sealer to cool down for 10 minutes before
storing.
The temperature controller is calibrated in centigrade to convert to fathrenheit.
(°Cx8/5 +32=°F)
For safety keep hands and fingers away from the jaws or hex nuts.
Elektronischer Schaltplan
Operating instructions
Benefits
Andere Sprintis Verpackungsanlagen Handbücher
