Squareled MRX Bar MKII Bedienungsanleitung

SquareLED - MRX Bar MKII

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

Caution!

• Be careful with your operations. With a dangerous voltage you can suer a dangerous electric shock when

touching the wires!

• Avoid looking directly into the light source!

• Keep this device away from rain and moisture!

• Make sure it is grounded when using it!

• Unplug mains lead before opening the housing!

• For your own safety, please read this user manual carefully before you initial start-up.

• Every person involved with the installation, operation and maintenance of this device has to

- be qualied

- follow the instructions of this manual

- consider this manual to be part of the total product

- keep this manual for the entire service life of the product

- pass this manual on to every further owner or user of the product

- download the latest version of the user manual from the Internet

Introduction

Thank you for having chosen Kongfu 18 Matrix MKII.You will see you acquired a powerful and versatile device.

Unpack your item. Before you initial start-up, please make sure that there is no damage caused by transportati-

on. Should there be any, consult your dealer and do not use the device.

Safety instructions

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure

a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes writ-

ten in this user manual.

Always disconnect from the mains, when the device is not in use or before cleaning it. Keep away children and

amateurs from the device! There are no serviceable parts inside the device. Maintenance and service operations

are only to be carried out by authorized dealers.

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

Installation

Read ‘Safety information’before installing the xture

The xture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure

that none of the xture’s ventilation slots are blocked. Fasten the xture to a secure structure or surface. Do not

stand it on a surface or leave it where it can be moved or fall over. If you install the xture in a location where it

may cause injury or damage if it falls, secure it as directed in this user manual using a securely anchored safety

cable that will hold the xture if the primary fastening method fails.

Fastening the xture to a at surface

The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure that the surface and

all fasteners used can support at least 10 times the weight of all xtures and equipment to be installed on it.

Fasten the xture securely. Do not stand it on a surface or leave it where it can be moved or fall over. If you install

the xture in a location where it may cause injury or damage if it falls, secure it as directed below with a securely

anchored safety cable that will hold the xture if the primary fastening method fails.

Mounting the xture on a truss

The xture can be clamped to a truss or similar rigging structure in any orientation. When installing the xture

hanging vertically down, you can use an open-type clamp such as a G-clamp. When installing in any other orien-

tation, you must use a half-coupler clamp that completely encircles the truss chord.

To clamp the xture to a truss:

1. Check that the rigging structure can support at least 10 times the weight of all xtures and equipment to be

installed on it.

2. Block access under the work area.

3. Fold the legs of the mounting bracket together and bolt a rigging clamp securely to the mounting bracket. The

bolt used must be M10, grade 8.8 steel minimum. It must pass through both mounting bracket legs and be

fastened with a self-locking nut.

4. Working from a stable platform, hang the xture with its clamp on the truss and fasten the clamp securely.

5. Secure the xture with a safety cable as directed below.

Securing with a safety cable

Secure the xture with a safety cable (or other secondary attachment) that is approved for the weight of the

xture so that the safety cable will hold the xture if a primary attachment fails. Loop the safety cable through

the eyebolt in the back of the xture and around a secure anchoring point. Do not loop the safety cable around

the xture’s mounting bracket only, as this will leave the xture unsecured if it separates from the bracket.

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

DMX-512 connection/connection between xtures

Occupation of the XLR-connection:

If you are using controllers with this occupation, you can connect the DMX-output of the controller directly with

the DMX-input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-

outputs, you need to use adapter-cables.

Building a serial DMX-chain:

Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always

connect one output with the input of the next xture until all xtures are connected.

DMX-512 connection with DMX terminator:

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment, such

as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of the digital

control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 resistor connected bet-

ween pins 2 and 3, which is then plugged into the output XLR socket of the last xture in the chain.

Caution:

At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal

(–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last xture.

Connection with the mains: Connect the device to the mains with the enclosed power supply cable.

Fixture overview

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

Operation

The Kongfu 18 Matrix MKII can operate in three dierent modes. In each mode you can run the xture as a stand

alone xture or in a master/slave conugration. This next section will detail the dif-ferences in the operating

modes.

Addressing

All xtures should be given a DMX starting address when using a DMX signal, so that the correct xture responds

to the correct control signals. This digital starting address is the channel number from which the xture starts to

listen to the digital control information sent out from the DMX controller. The allocation of this starting address is

achieved by setting the correct number on the display located on the base of the device.

You can set the same starting address for all xtures or a group of xtures, or make dierent address for each

xture individually.

If you set the same address, all the units will start to listen to the same control signal from the same channel

number. In other words, changing the settings of one channel will aect all the xtures simultaneously.

If you set a dierent address, each unit will start to listen to the channel number you have set, based on the

quantity of control channels of the unit.That means changing the settings of one channel will aect only the

selected xture.

In the case of the Kongfu 18 Matrix MKII, which is 6/19/29/77 channels xture. If you set, for example, the

address in the 19 channel mode to channel 20, the device will use the channel 20 to 38 for control.

Universal DMX Control

This function allows you to use a universal DMX-512 controller to control the chases and patterns, dimmer and

strobe. A DMX controller allows you to create unique programs tailored to your individual needs.

Note: Always set MENU to address mode(A.001-A.512) when using DMX control!

Stand-alone Mode

In this mode, you can run internal program without a controller.

1. Press the MENU button until“Prxx”is displayed, and press ENTER.

2. Press the UP or DOWN button to select from“Pr01”to“Pr26”, which represent 25 preset programs.

3. The unit will run built-in programs.

Sound Active Mode

This mode allows either single unit or several units linked together, to run to the beat of the music.

1. Press the MENU button until“Auto”/“Aud1”is displayed, and press ENTER.

2. Press the UP or DOWN button so that“Aud1”is displayed. Press ENTER. The unit will now run to the beat of the

music.

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

Master-Slave Operation

This function will allow you to link up to 16 units together and operate without a controller. In a Master-Slave set

up one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the

units.

2. The followings can be operate as master mode: r001-r255, G001-G255, b001-b255, H001-H255, Pr01-Pr26,

Auto/Aud1. For the Master unit press the MENU button and select any of these mode. Press ENTER.

3. For the slave units press the MENU button until“A001”is displayed, and Press ENTER.

4. The slave units will now follow the Master unit.

Control Menu Map

MENU SUB-MENU FUNCTION INSTRUCTION

d001 d001-d512 DMX address setting

r000 r000-r255 Red dimmer

G000 G000-G255 Green dimmer

B000 B000-B255 Blue dimmer

H000 H000-H255 White dimmer

PR01 Pr01-PR26 Internal programs

sp01 SP01-sp16 Internal program speed increasing

LD01 LD01 Dimmer curve-linearly

LD02 Dimmer curve-exponential(delay)

SP01 sp01-sp16 Internal programs speed increasing

Auto Auto Auto Mode

Aud1 Sound mode

dISP dISP Display reverse o

dSIP Display reverse 180 degrees

5CH 5/19/29/77 CH Channel mode

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

DMX Protocol

5 CH Fuction Description

CH1 Dimmer 0-255 0-100% linear dimmer

CH2 Red 0-255 Red dimming 0-100%

CH3 Green 0-255 Blue dimming 0-100%

CH4 Blue 0-255 Green dimming 0-100%

CH5 White 0-255 White dimming 0-100%

19 CH Fuction Description

CH1 Dimmer 0-255 0-100% linear dimmer

CH2 Strobe 0-255 Speed increasing

CH3 Red 0-255 Red dimming 0-100%

CH4 Green 0-255 Blue dimming 0-100%

CH5 Blue 0-255 Green dimming 0-100%

CH6 White 0-255 White dimming 0-100%

CH7 Internal program speed 0-255 Speed increasing

CH8 Internal program 0-14 No func.

15-255 Internal program

CH9 Colour temperature 0-10 No func.

11-255 Colour temperature increasing

CH10 Colour mixing 0-9 No func.

10-255 Various colour mixing eect

CH11 Colour marco

0-5 No func.

6-128 Various colour mixing eect

129-170 Colour switching(jumping)

171-212 Colour fading

213-255 Internal programs

CH12 Red(Group 1, LED 1-9) 0-255 Red dimming 0-100%

CH13 Green(Group 1, LED 1-9) 0-255 Blue dimming 0-100%

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

CH14 Blue(Group 1, LED 1-9) 0-255 Green dimming 0-100%

CH15 White(Group 1, LED 1-9) 0-255 White dimming 0-100%

CH16 Red(Group 2, LED 10-18) 0-255 Red dimming 0-100%

CH17 Green(Group 2, LED 10-18) 0-255 Blue dimming 0-100%

CH18 Blue(Group 2, LED 10-18) 0-255 Green dimming 0-100%

CH19 White(Group 2, LED 10-18) 0-255 White dimming 0-100%

Note: From the opposite side of the display, LED 1 is the rst LED...LED 18 is the last LED.

29 CH Fuction Description

CH1 Dimmer 0-255 0-100% linear dimmer

CH2 Strobe 0-255 Speed increasing

CH3 Red(LED 1-3) 0-255 0-100% 3 LED of rst group

CH4 Green(LED 1-3) 0-255 0-100% 3 LED of rst group

CH5 Blue(LED 1-3) 0-255 0-100% 3 LED of rst group

CH6 White(LED 1-3) 0-255 0-100% 3 LED of rst group

CH7 Red(LED 4-6) 0-255 0-100% 3 LED of second group

CH8 Green(LED 4-6) 0-255 0-100% 3 LED of second group

CH9 Blue(LED 4-6) 0-255 0-100% 3 LED of second group

CH10 White(LED 4-6) 0-255 0-100% 3 LED of second group

CH11 Red(LED 7-9) 0-255 0-100% 3 LED of third group

CH12 Green(LED 7-9) 0-255 0-100% 3 LED of third group

CH13 Blue(LED 7-9) 0-255 0-100% 3 LED of third group

CH14 White(LED 7-9) 0-255 0-100% 3 LED of third group

CH15 Red(LED 10-12) 0-255 0-100% 3 LED of fourth group

CH16 Green(LED 10-12) 0-255 0-100% 3 LED of fourth group

CH17 Blue(LED 10-12) 0-255 0-100% 3 LED of fourth group

CH18 White(LED 10-12) 0-255 0-100% 3 LED of fourth group

CH19 Red(LED 13-15) 0-255 0-100% 3 LED of fth group

CH20 Green(LED 13-15) 0-255 0-100% 3 LED of fth group

CH21 Blue(LED 13-15) 0-255 0-100% 3 LED of fth group

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

CH22 White(LED 13-15) 0-255 0-100% 3 LED of fth group

CH23 Red(LED 16-18) 0-255 0-100% 3 LED of sixth group

CH24 Green(LED 16-18) 0-255 0-100% 3 LED of sixth group

CH25 Blue(LED 16-18) 0-255 0-100% 3 LED of sixth group

CH26 White(LED 16-18) 0-255 0-100% 3 LED of sixth group

CH27 Colour mixing 0-255 Various colour mixing eect

CH28 Internal program 0-10 No func.

11-255 Internal programs

CH29 Internal program speed 0-255 Speed increasing

Note: From the opposite side of the display, LED 1 is the rst LED...LED 18 is the last LED.

77 CH Fuction Description

CH1 Dimmer 0-255 0-100% linear dimmer

CH2 Strobe 0-255 Speed increasing

CH3 Red(LED 1) 0-255 0-100% LED 1

CH4 Green(LED 1) 0-255 0-100% LED 1

CH5 Blue(LED 1) 0-255 0-100% LED 1

CH6 White(LED 1) 0-255 0-100% LED 1

CH7 Red(LED 2) 0-255 0-100% LED 2

CH8 Green(LED 2) 0-255 0-100% LED 2

CH9 Blue(LED 2) 0-255 0-100% LED 2

CH10 White(LED 2) 0-255 0-100% LED 2

CH11 Red(LED 3) 0-255 0-100% LED 3

CH12 Green(LED 3) 0-255 0-100% LED 3

CH13 Blue(LED 3) 0-255 0-100% LED 3

CH14 White(LED 3) 0-255 0-100% LED 3

CH15 Red(LED 4) 0-255 0-100% LED 4

CH16 Green(LED 4) 0-255 0-100% LED 4

CH17 Blue(LED 4) 0-255 0-100% LED 4

CH18 White(LED 4) 0-255 0-100% LED 4

Manual | MRX Bar MKII (LED BAR 18x12W RGBW OUTDOOR)

CH19 Red(LED 5) 0-255 0-100% LED 5

CH20 Green(LED 5) 0-255 0-100% LED 5

CH21 Blue(LED 5) 0-255 0-100% LED 5

CH22 White(LED 5) 0-255 0-100% LED 5

CH23 Red(LED 6) 0-255 0-100% LED 6

CH24 Green(LED 6) 0-255 0-100% LED 6

CH25 Blue(LED 6) 0-255 0-100% LED 6

CH26 White(LED 7) 0-255 0-100% LED 7

CH27 Red(LED 7) 0-255 0-100% LED 7

CH28 Green(LED 7) 0-255 0-100% LED 7

CH29 Blue(LED 7) 0-255 0-100% LED 7

CH30 White(LED 7) 0-255 0-100% LED 7

CH31 Red(LED 8) 0-255 0-100% LED 8

CH32 Green(LED 8) 0-255 0-100% LED 8

CH33 Blue(LED 8) 0-255 0-100% LED 8

CH34 White(LED 8) 0-255 0-100% LED 8

CH35 Red(LED 9) 0-255 0-100% LED 9

CH36 Green(LED 9) 0-255 0-100% LED 9

CH37 Blue(LED 9) 0-255 0-100% LED 9

CH38 White(LED 9) 0-255 0-100% LED 9

CH39 Red(LED 10) 0-255 0-100% LED 10

CH40 Green(LED 10) 0-255 0-100% LED 10

CH41 Blue(LED 10) 0-255 0-100% LED 10

CH42 White(LED 10) 0-255 0-100% LED 10

CH43 Red(LED 11) 0-255 0-100% LED 11

CH44 Green(LED 11) 0-255 0-100% LED 11

CH45 Blue(LED 11) 0-255 0-100% LED 11

CH46 White(LED 11) 0-255 0-100% LED 11

CH47 Red(LED 12) 0-255 0-100% LED 12

CH48 Green(LED 12) 0-255 0-100% LED 12

Inhaltsverzeichnis

Andere Squareled DJ-Equipment Handbücher

Squareled

Squareled Hi-Precision 300W LED Profiler MK2 fixed Bedienungsanleitung

Squareled

Squareled LTH PRO.fessional Bedienungsanleitung

Squareled

Squareled LUMINO 200W-RGBW Bedienungsanleitung

Squareled

Squareled LED MATRIX 16X30W COB BLINDER Bedienungsanleitung

Squareled

Squareled Hi-Precision 500W RGBAL Zoom Bedienungsanleitung

Squareled

Squareled Bajazzo Kurzanleitung

Squareled

Squareled Aura Bar & Matrix Beam Light 100 Bedienungsanleitung

Squareled

Squareled Funky Bee Bedienungsanleitung

Squareled

Squareled Blade 7 Bedienungsanleitung

Squareled

Squareled Vintage PAR Senior LED Bedienungsanleitung

Squareled

Squareled Ventura 6x25W RGBAW Matrix Bar Bedienungsanleitung

Squareled

Squareled Splash 200W Fresnel IP65 Bedienungsanleitung

Squareled

Squareled Dancefloor Bedienungsanleitung

Squareled

Squareled Hi-Precision 500W RGBAL Zoom Bedienungsanleitung

Squareled

Squareled PQ1036 Bedienungsanleitung

Squareled

Squareled Moving Blade Bedienungsanleitung

Squareled

Squareled Color Designer 18x12W RGBAW+UV Bedienungsanleitung

Squareled

Squareled STORM 5 Bedienungsanleitung

Squareled

Squareled Aura Panel gold matrix & dream color Bedienungsanleitung

Squareled

Squareled SquareLED Zyclone 300W RGBAL Bedienungsanleitung

Squareled

Squareled SPIRIT Bedienungsanleitung

Squareled

Squareled LED CYC LIGHT 48x3W RGBA Bedienungsanleitung

Squareled

Squareled Edgy Bedienungsanleitung

Squareled

Squareled tricolor ip65 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung