Ssl CLZMF Betriebsanleitung
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
Fig 1
GENERAL:
1. Before starting the installation, make sure all electricity has
been turned off and electrical breaker has been locked out
and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly
before beginning.
3. All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur.
INSTALLATION:
Recommended: Due to the weight of the luminaire it is
recommended to use two installers for safe handling.
1. Identify all parts are present for assembly and use a sturdy
surface to complete assembly. Fig 1
2. Prepare end bolts for assembly by placing the Split
Washer on the bolt. Fig 2
3. Re-Insert the end-bolts onto the housing and hand-tighten.
4. Using the arrows located on side of luminaire, adjust beam
target. Fig 3
5. Once desired angle is reached, Tighten to 90 IN-LBS with
a 5 mm hex
WARNING: Failure to tighten luminaire to an adequate torque
value will result 3G vibration Failure.
Fig 2
Fig 3
Loctite 271
5 MM
END BOLT
SPLIT-WASHER
BIT TYPE: 5 MM
TIGHTEN TO 90 IN-LBS
SPLIT-WASHER
LOCTITE 271
APPLY LOCTITE HERE
BETWEEN MEASUREMENTS
0.75 inch
1.10 inches
USE ARROWS ON
SIDE OF LUMINIAIRE
TO ADJUST ANGLE
BEFORE TIGHTENING
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
DRIVE SIZE: 2.5 MM
TORQUE: 15 IN-LBS
2.5 MM
DRIVE SIZE: 2.5 MM
TORQUE: 15 IN-LBS
2.5 MM
DRIVE SIZE: 2.5 MM
TORQUE: 15 IN-LBS
2.5 MM
Fig 1
GENERAL:
1. Before starting the installation, make sure all electricity has been
turned off and electrical breaker has been locked out and tagged out.
2. To ensure the success of the installation, be sure to read these
instructions and review the diagrams thoroughly before beginning.
3. All electrical connections must be in accordance with local codes,
ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing in this
manual are not meant to cover all possible conditions and situations
that may occur.
INSTALLATION:
FULL VISOR (FV)
1. Place the Full Visor over the top of the Micro Flood luminaire and align
the four holes in the Visor with the four screw holes on the luminaire.
Fig 1
2. Fasten the Full Visor down onto the Micro Flood luminaire using the
four provided screws. Tighten evenly alternating opposite sides. Fig 2
HALF VISOR (HV)
IMPORTANT: Ensure you’re installing the Half Visor with the high side
on the appropriate side of the luminaire for the intended light cutoff.
1. Place the Half Visor over the top of the Micro Flood luminaire and align
the four holes in the Visor with the four screw holes on the luminaire.
Fig 3
2. Fasten the Half Visor down onto the Micro Flood luminaire using the
four provided screws. Tighten evenly alternating sides. Fig 4
ROCK GUARD (RG)
IMPORTANT: Ensure you’re installing the Rock Guard so that the
optics line up in between the guard slats to prevent light cutoff.
1. Place the Rock Guard over the top of the Micro Flood luminaire and
align the four holes in the Visor with the four screw holes on the
luminaire. Fig 3
2. Fasten the Rock Guard down onto the Micro Flood luminaire using the
four provided screws. Tighten evenly alternating sides. Fig 4
Fig 3
Full Visor (FV) Half Visor (HV)
Fig 5
Rock Guard (RG)
Fig 2 Fig 4 Fig 6
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
Fig 1 All Connections on Back of Luminaire
GENERAL:
1. Before starting the installation, make sure all electricity
has been turned off and electrical breaker has been
locked out and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly
before beginning.
3. All electrical connections must be in accordance with
local codes, ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing
in this manual are not meant to cover all possible conditions
and situations that may occur.
INSTALLATION:
1. Once the Modules and Bracket Arms have been
assembled and bolted into place, the next step is to run
power and data lines to and from the luminaire modules.
2. All connections to and from the modules are made on
the bottom of the luminaires. Fig 1
IMPORTANT: Maximum Units in a Run: 9 Modules (120V)
REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap
(TCAPDCLZ) are required for every run.
ColourLine Lazer — Basic Luminaire Wiring
STARTER CORD (SCxxCLZ)
Required Started Cord comes with a luminaire connector at one
end and lead wires at the other end for connecting power & data.
EXTENSION CORD (ECxxCLZ)
The Extension Cord comes with a luminaire connection at each
end for connecting power & data.
TERMINATOR CAP (TZCAPDCLZ)
Required Started Cord comes with a luminaire connector at one
end and lead wires at the other end for connecting power & data.
10, 25, or 50 feet
24, 60 120, or 240 inches
120 Oh
m
Resister
CONNECTION ARE MADE HERE.
CONNECT TO EITHER SIDE, BOTH
CONNECTORS ARE THE SAME.
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
GENERAL:
1. Before starting the installation, make sure all electricity
has been turned off and electrical breaker has been
locked out and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly
before beginning.
3. All electrical connections must be in accordance with
local codes, ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing
in this manual are not meant to cover all possible conditions and
situations that may occur.
INSTALLATION:
1. Verify Physical Layout Plan
a. Ensure all luminaires, components and wiring hardware are
present before starting installation.
b. Fasten the luminaires and other components in place.
c. Run wire cable and complete connections as indicated
in the diagrams to the right.
2. All connections to and from the modules are made on
the bottom of the luminaires.
HARDWARE: May include RDM Controller, Exterior Rated
Data Line, AC Power Feed, PDX/S box, PDX box, Starter
Cords, Terminator Caps, Extension Cables and luminaires.
NOTE: Use Extension Cable when necessary, for corners
and extending luminaire runs.
IMPORTANT: Maximum Units in a Run: 9 Modules (120V)
REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap
(TCAPDCLZ) are required for every run.
ColourLine Lazer — Basic Component Congurations
Component Identication
1) DMX Color Controller (see last page)
2) DMX Data Cable DXC-xx or CD-xx (CSC only)
3) PDX Power Data Wiring Box
4) Starter Cord SCxxCLZ
5) ColourLine Lazer (CLZMF)
6) Extension Cord ECxxCLZ (connect at back
of luminaire)
7) Connected ColourLine Lazer Micro (CLZMF)
8) Extension Cords connect luminaires ECxxCLZ
9) Terminator Cap TCAPDCLZ (required at end of run)
10) Maximum Units in a Run (before adding more power):
9Modules (120V),18 Modules (277V)
Back of Luminaire Connections
Connect to either side, both
connectors are the same.
Back of Luminaire Connections
Maximum Units in a Run = 9 Modules (120V)
J-Box
CTRL
(Underneath)
Terminator Ca
p
Required to
End Each Run
8
6
5
7
4
10
3
2
1
9
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
DMX/RDM
Controller
Extension Cord (ECxxCLZ)
(xx = 24, 60, 120, or 240 inches)
Starter Cord (SCxxCLZ)
(xx = 10, 25, or 50 feet)
End Run with
Terminator Cap
(TCAPDCLZ)
AC Input
(120-277V)
AC Input
(120-277V)
Extension Cord (ECxxCLZ)
(xx = 24, 60, 120, or 240 inches)
Starter Cord (SCxxCLZ)
(xx = 10, 25, or 50 feet)
End Run with
Terminator Cap
(TCAPDCLZ)
AC Input
(120-277V)
To Next
PDX2/S
AC
(
12
0
AC
(12
0
GENERAL:
1. Before starting the installation, make sure all electricity has been
turned off and electrical breaker has been locked out and tagged out.
2. To ensure the success of the installation, be sure to read these
instructions and review the diagrams thoroughly before beginning.
3. All electrical connections must be in accordance with local codes,
ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing in this
manual are not meant to cover all possible conditions and situations
that may occur.
INSTALLATION:
1. Verify Physical Layout Plan
a. Ensure all hardware is present.
b. Ensure all electrical feeds are correctly positioned with all
hardware and any other active components.
c. Conrm DMX Addressing Plan
i. SSL recommends pre-addressing xtures before
mounting installation.
ii. Ensure that addressing is documented for future
upgrading, conguring or troubleshooting.
HARDWARE: May include RDM Controller, Exterior Rated
Data Line, AC Power Feed, PDX-S box, PDX2 box, Starter
Cords, Terminator Caps, Extension Cables and xtures.
NOTE: Use Extension Cable when necessary, for corners and
extending xture runs.
IMPORTANT: Maximum Units in a Run: 9 Modules (120V)
REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap
(TCAPDCLZ) are required for every run.
CLZMF RGBW — Multiple Segment Conguration
STARTER CORD (SCxxCLZ) TERMINATOR CAP (TZCAPDCLZ)
120 Oh
m
Resister
6-Pin Connectors
2.4 inches
N
G
L
3 Data (-)
2 Data (+)
1 G
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
GENERAL:
1. Before starting the installation, make sure all electricity has
been turned off and electrical breaker has been locked out
and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly
before beginning
3. All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code.
NOTE: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur.
INSTALLATION:
1. PDX2 (Power/ Data Box)
a. Mount PDX2 (PDX2 is exterior-rated).
NOTE: Use appropriate fasteners (#10 screws) for mounting to
surface type.
PDX2 — Power/Data Box
BLACK — LINE
WHITE — NEUTRAL
GREEN — GROUND
PURPLE — DATA+
PINK — DATA-
Cable Accessories (order separately)
Accessories (Indicate the quantity needed for each item.) REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap (TCAPDCLZ) for every run.
SC10CLZ 10 feet Starter Connection Cord
SC25CLZ 25 feet Starter Connection Cord
SC50CLZ 50 feet Starter Connection Cord
TCAPDCLZ Data Terminator Cap (120 Ohm)
EC24CLZ 24 inches Extension Cord
EC60CLZ 60 inches Extension Cord
EC120CLZ 120 inches Extension Cord
EC240CLZ 240 inches Extension Cord
3.6 inches
7.4 inches
3.8 inches
6.6 inches
6.1 inches
7.8 inches
4.8 inches
6.8 inches
Top View
Front View Side View
Use
(4) #10
Screws
CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
TG-TD-092623
CLZMF
t800.900.1730
3609 Swenson Ave.
St. Charles, IL 60174
DETAILED ILLUSTRATION
©SOLID STATE LUMINAIRES.
GENERAL:
1. Before starting the installation, make sure all
electricity has been turned off and electrical
breaker has been locked out and tagged out.
2. To ensure the success of the installation, be sure
to read these instructions and review the diagrams
thoroughly before beginning.
3. All electrical connections must be in accordance
with local codes, ordinances, or the National
Electrical Code.
NOTE: The important safeguards and instructions
appearing in this manual are not meant to cover all
possible conditions and situations that may occur.
INSTALLATION:
1. PDX2 (Power/ Data Box)
a. Mount PDX2 (PDX2 is exterior-rated).
NOTE: Use appropriate fasteners (#10 screws) for mounting
to surface type.
b. PDX2 Wiring Diagram
PDX2 — Power/Data Box
Ground (G)
Neutral (N)
Line (L)
AC Power (IN)
Shield
(+) Data (Purple)
(–) Data (
Pink or Gray)
Ground (G)
Neutral (N)
Line (L)
Fixture (OUT)
TOP VIEW
DMX Controller (IN)
Wire Shield
Shield
Data (+) (Blue w/ White Dash)
Data (–) (White w/
Blue Dash)
PDX2 Wiring
BLACK — LINE
WHITE — NEUTRAL
GREEN — GROUND
PURPLE — DATA+
PINK — DATA-
Inhaltsverzeichnis
Andere Ssl Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
