Ssl M325USA Bedienungsanleitung

M325USA

CD/MP3/SD/MMC Receiver With

Large LCD With Power Level Meter

Installation.......................................................................2

Install and remove the front panel.......................................4

Wiring diagram.................................................................5

Control panel layout..........................................................6

General operation.............................................................7

Radio operation...............................................................10

CD/MP3 Operations.........................................................12

MP3 Operations...............................................................13

Remote control layout......................................................14

Specificaton....................................................................16

Before playing discs.........................................................17

Trouble shooting..............................................................18

INSTALLATION

NOTES ON INSTALLATION

● Choose the mounting location where the unit will not interfere with the

normal driving function of the driver.

● Before finally installing the unit, connect the wiring temporarily and make

sure it is all connected up properly and the unit and the system work properly.

● Use only the parts included with the unit to ensure proper installation. The

use of unauthorized parts can cause malfunctions.

● Consult with your nearest dealer if installation requires the drilling of holes

or other modifications of the vehicle.

● If installation angle exceeds 30 degrees horizontally, the unit might not

give its optimum performance.

● Avoid installing the unit where it would be subject to high temperature,

such as from direct sunlight, or from hot air, form the heater, or where it

would be subject to dust, dirt or excessive vibration. Do not expose the

equipment to rain or moisture.

DIN FRONT-MOUNT (Method A)

Installing the unit

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

select the appropriate tab according to the

thickness of the dashboard material and bend

them inwards to secure the holder in (Fig. 1)

place.

3. Screw

INSTALLATION

1. Dashboard

2. Nut (5mm)

3. Spring Washer

4. Screw (5 x 25mm)

5. Screw

6. Strap

Be sure to use the strap to

secure the back of the unit in

place. The strap can be bent by

hand to the desired angle.

7. Plain Washer

1.Frame

2.Insert fingers into the groove in the

front of frame and pull out to remove

the frame. (When reattaching the

frame, point the side with a groove

downwards and attach it.)

3.Lever

Insert the levers supplied with the

unit into the grooves at both sides of

the unit ad shown in figure until they

click. Pulling the levers makes possible

to remove the unit from the

dashboard.

Fastening the unit to the factory

radio mounting bracket:

DIN REAR-MOUNT (Method B)

INPUT THE SD CARD

1. Select a position where the screw

holes of the bracket and the

screw holes of the main unit

become aligned (are fitted), and

tighten the screws at 2 places on

each side. Use either truss screws

(5 x 5mm) or flush surface screws

(4 x 5mm)

2. Screw

3. Dashboard or Console

Installation using the screw holes

on the sides of the unit.

The SD angle should be on top to

slide into this unit. Push it inside

the slot to make it work and then

press it again to have it eject.

INSTALLING THE FRONT PANEL

To install the front panel, insert the panel into the housing and make sure

the panel Is properly installed, otherwise, abnormalities occurs on the

display or some keys will not function properly.

DETACHING THE FRONT PANEL

Press REL button in the upper left

corner, and hen front panel will not

function properly.

REMOVING THE FRONT PANEL

When the front panel was turned down

to a position of 90 , hold and slide the

front panel to left, and then pull it out.

INSTALL AND REMOVE THE FRONT PANEL

WIRING DIAGRAM

WIRE CONNECTION

!NOTE

BE SURE THE UNIT IS CONNECTED TO A 12 VOLTS BATTERY WITH

NEGATIVE GROUND . THE POSITIVE (+) CABLES MUST BE

CONNECTED TO THE POSITIVE (+) BATTERY TERMINAL.

THE NEGATIVE CABLE (-) MUST BE CONNECTED TO GROUND/

CHASSIS. SPEAKERS SHOULD BE CONNECTED CORRECTLY (+)

WITH (+) AND (-) WITH (-). FAILURE TO DO SO WILL DAMAGE THE UNIT.

CONTROL PANEL LAYOUT

FRONT PANEL LAYOUT

GENERAL OPERATIONS

ON/OFF

FRONT PANEL RELEASE

SOUND ADJUSTMENT

VOLUME

BASS

TREBLE

BALANCE

FADER

Press POWER button (1) to turn on the unit. Press it again to turn off.

Press REL button (2) to detach the removable front panel.

Turn on (3) can adjust the desired volume quality.

A).Press SEL button (3)will change in the following order.

Option:

Adjust volume level by using VOL/SEL (3) knob.

Press VOL/SEL button(3) one time. Adjust bass level by using VOL/SEL(3)

Knob.

Press VOL/SEL button(3) two times. Adjust treble level by using VOL/SEL(3)

Knob.

Press VOL/SEL button(3) three times. Adjust sound balance between left

and right speakers by using VOL/SEL(3)Knob.

Press SEL button(3) four times. Adjust sound balance between front and

rear speakers by using VOL/SEL(3)Knob.

Note: The unit is initially set to volume mode.

MUTE

Press MUTE button(4) mute down the sound. Press it again to release this

mode and recover previous volume level.

GENERAL OPERATIONS

If you press the Vol/SEL button (3) for several seconds, it will activate a

cycling mode of the following functions for user's selection.

Press and hold this button to go to DSP Mode. By turning this function

button, you will cycle thru Flat, Classic, Pop and Rock. Press the function

button to select your favorite DSP mode.

When in DSP mode, pressing the function button once will take you to ESP

Mode. Turning the function button will allow you to choose 12 seconds or 45

seconds ESP. Press the function button to select your desired ESP setting.

When in DSP mode pressing the function button twice will take you to Beep

Mode, (the key pad tone). Turning the function button will allow you to

choose ON or OFF. Press the function button to select.

This function allows the user to set the volume level of the unit after it was

turned off and then turned on again. Choose VOL LAST if you want the

volume level to be the same as it was before turning off. VOL ADJUST

allows to choose volume level.

SEEK 1: When SEEK 1 mode is activated, AUTO SEEK SCAN is stopped

when station is detected even user still push SEEK button.

SEEK 1: When SEEK 1 mode is activated, AUTO SEEK SCAN is stopped

when station is detected even user still push SEEK button.

SEEK 2: Auto SEEK SCAN is not stopped even if station is detected if user

pushes SEEK button. When releases SEEK button, then stop when station

is detected.

Press button (5) to go to different functions.

OTHERS ADJUSTMENT

VOL LAST/ADJUST

SEEK MODE

SELECT MODE

GENERAL OPERATIONS

- CD (MP3 CD)

to go to this mode must be have a CD in.

- Memory Card

to go to this mode must be have a Memory Card in.

- USB

to go to this mode USB device must be connected.

- AUX in put

Press DISP button (6) to operate each display mode as follow:

- Time is displayed for 5sec when DISP key is pressed, it will then return to

its previous display ( Folder, File name...) unless DISP key is pressed again.

From the clock mode, when DISP Key is pressed for longer than 1sec, clock

mode switches to clock Adjusting mode and the clock display begins

flashing. At this time clock can be changed by pressing (+/-), or the

ENCODER VOLUME.

Exhibit current frequency and activated functions on the display (7).

If the front panel dis not correctly installed on the main unit,, the LED (8)

will be flashing.

RESET button (9) is placed on the housing and must be activated with either

a ball point pen or thin metal object. (Do not use sharp object to avoid

damaging the unit.) The RESET button (9) is to be activated for the following

reasons:

- Initial installation of the unit when all wiring is completed.

- All the function buttons do not operate.

- Error symbol on the display.

- Tuner (radio)

DISPLAY

MP3 MODE

LIQUID CRYSTAL DISPLAY

FLASHING LED

RESET

NOTE: If press RESET button (9), the unit can't work yet. please use a

cotton swab soaked in isopropyl alcohol to clean the socket on the back of

the front panel.

Inhaltsverzeichnis

Andere Ssl Stereo-Receiver Handbücher

Ssl

Ssl DDML65B Bedienungsanleitung

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Yamaha

Yamaha RX-830 Bedienungsanleitung

Pioneer

Pioneer AVH-Z7250BT Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Denon

Denon AVR-1311 Bedienungsanleitung

Denon

Denon AVR-S760H Bedienungsanleitung

Denon

Denon AVR-X7200W Bedienungsanleitung

Pioneer

Pioneer SC-LX904 Handbuch

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Pioneer

Pioneer SX-1000TA Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Pioneer

Pioneer SX-838 Bedienungsanleitung