SSV IGW/922 Anwendungshandbuch

Remote Access Gateway IGW/922

with DIL/NetPC ADNP/9200

Hardware Reference

SSV Embedded Systems

Dünenweg 5

D-30419 Hannover

Phone: +49 (0)511/40 000-0

Fax: +49 (0)511/40 000-40

E-mail: sales@ssv-embedded.de Document Revision: 1.3

Date: 2012-04-12

OR FURTHER INFORMATION REGARDING OUR PRODUCTS PLEASE VISIT US AT WWW

SSV

EMBEDDED

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

CONTENT

1INTRODUCTION...............................................................................................................3

1.1 Safety Guidelines...................................................................................................................3

1.2 Conventions...........................................................................................................................3

1.3 Features and Technical Data..................................................................................................4

1.4 Main Applications .................................................................................................................4

2OVERVIEW .......................................................................................................................5

3PINOUTS ..........................................................................................................................6

3.1 Screw Terminals ....................................................................................................................6

3.2 Ethernet LAN1 and LAN2.....................................................................................................7

3.3 Serial Port COM1 ..................................................................................................................7

4CONNECTIONS................................................................................................................8

4.1 Serial Port COM2 ..................................................................................................................8

4.2 Power Supply.........................................................................................................................9

4.3 Semiconductor Relay Output...............................................................................................10

5HELPFUL LITERATURE.................................................................................................11

CONTACT..............................................................................................................................11

DOCUMENT HISTORY .........................................................................................................11

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

1 INTRODUCTION

This document describes the hardware components and the necessary cable connections of

the Remote Access Gateway IGW/922.

1.1 Safety Guidelines

Please read the following safety guidelines carefully! In case of property or personal

damage by not paying attention to this document and/or by incorrect handling, we do

not assume liability. In such cases any warranty claim expires.

ATTENTION: Observe precautions for handling – electrostatic sensitive device!

•Discharge yourself before you work with the device, e.g. by touching a heater of

metal, to avoid damages.

•Stay grounded while working with the device to avoid damage through electrostatic

discharge.

1.2 Conventions

Convention Usage

bold

Important terms

italic

Filenames, user inputs and command lines

monospace Pathnames, internet addresses and program code

Table 1: Conventions used in this document

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

1.3 Features and Technical Data

•1x QIL-128 socket for DIL/NetPC ADNP/9200

•1x modem socket option for GSM/GPRS/UMTS/HSPA wireless modems

•2x 10/100 Mbps Ethernet LAN interface with status LEDs

•1x RS232 serial port (COM1) with handshake lines and 9-pin Sub-D connector

•1x RS232/485 serial port (COM2) with 3-pin screw terminal and software-selectable

mode switch

•1x semiconductor relay output (30 VDC, 500 mA)

•1x power LED

•1x user LED (programmable)

•Supply voltage 11 .. 28 VDC (typ. 24 VDC)

•Mechanical dimensions: 45 mm x 100 mm x 112 mm

•0 °C to +70 °C operating temperature

•RoHS conform

1.4 Main Applications

•Remote Access Security Gateway

•GPRS/UMTS Router

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

2 OVERVIEW

Figure 1: Overview Remote Access Gateway IGW/922

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

3 PINOUTS

3.1 Screw Terminals

The table 2 shows the pinout of the screw terminals of the IGW/922.

Power COM2 Alarm

RS232 RS485*

Alarm -

Alarm +

V+ IN

GND IN

TXD RX/TX -

RXD RX/TX +

GND GND

Table 2: Pinout of the screw terminals

* Please note: The RS485 (officially called TIA/EIA-485-A) connection between

your IGW/922 and the field devices needs termination resistors on both ends for

proper operation. The IGW/922 does not offer internal termination resistors. Please

make sure, that the RS485 cable connection is equipped with external termination re-

sistors.

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

3.2 Ethernet LAN1 and LAN2

The Ethernet LAN1 and LAN2 interfaces are standard RJ45 connectors.

Both have a green LED. It is on when there is a LAN link established and blinks when there

is traffic. The yellow LED is not connected.

Name Function

TX+ 10/100 Mbps LAN, TX+ Pin

TX- 10/100 Mbps LAN, TX- Pin

RX+ 10/100 Mbps LAN, RX+ Pin

--- Not Connected

RX- 10/100 Mbps LAN, RX- Pin

--- Not Connected

Table 3: Pinout Ethernet interfaces

3.3 Serial Port COM1

The serial port COM1 is a standard Sub-D connector.

Name Function

DCD COM1 Serial Port, DCD pin (RS232)

RXD COM1 Serial Port, RXD pin (RS232)

TXD COM1 Serial Port, TXD pin (RS232)

DTR COM1 Serial Port, DTR pin (RS232)

GND Ground

DSR COM1 Serial Port, DSR pin (RS232)

RTS COM1 Serial Port, RTS pin (RS232)

CTS COM1 Serial Port, CTS pin (RS232)

DCD COM1 Serial Port, DCD pin (RS232)

Table 4: Pinout COM1 connector

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

4 CONNECTIONS

4.1 Serial Port COM2

To create an RS232 serial link on port COM2 of the Remote Access Gateway IGW/922 con-

nect the adapter cable and the null-modem cable like shown in the figure below.

Figure 2: RS232 link on serial port COM2

Terminal Signal

B2 COM2 Serial Port: TXD (RS232), RX/TX- (RS485)

B3 COM2 Serial Port: RXD (RS232), RX/TX+ (RS485)

B4 Ground

Table 5: Screw terminal COM2

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

4.2 Power Supply

The Remote Access Gateway IGW/922 needs a supply voltage of 11 .. 28 VDC to work. Use

the power adapter cable to provide the system with the necessary power like shown in the

figure below.

Figure 3: Power supply for the Remote Access Gateway IGW/922

Terminal Signal

A3 Vin (11 .. 28 VDC)

A4 GNDin

Table 6: Screw terminal power

CAUTION: Providing the Remote Access Gateway IGW/922 with a higher voltage than the

regular 11 .. 28 VDC could cause damaged board components!

CAUTION: Do NOT turn on the power supply while connecting the power adapter cable

with the Remote Access Gateway IGW/922. This could cause damaged board components!

First connect the power adapter cable and THEN turn the power supply on.

Remote Access Gateway IGW/922 - Hardware Reference

Board Revision 1.0 / Manual Revision 1.3

4.3 Semiconductor Relay Output

The Remote Access Gateway IGW/922 offers a semiconductor relay output to switch an ex-

ternal alarm device with up to 30 VDC and 500 mA on and off.

Figure 4: Connecting an external alarm device

Terminal Signal

A1 Alarm- Semiconductor Relay Output (max. 30 VDC / 500 mA)

A2 Alarm+ Semiconductor Relay Output (max. 30 VDC / 500 mA)

Table 7: Screw terminal semiconductor relay output

CAUTION: Using the alarm output with more than the regular 30 VDC and 500 mA could

cause damaged board components!

Andere Handbücher für IGW/922

Inhaltsverzeichnis

Andere SSV Tor Handbücher

SSV

SSV IGW/935 Anwendungshandbuch

SSV

SSV RMG/938 Bedienungsanleitung

SSV

SSV IGW/925 Installations- und Benutzerhandbuch

SSV

SSV RMG/941 Series Anwendungshandbuch

SSV

SSV IGW/941 Anwendungshandbuch

SSV

SSV MGW/865 Bedienungsanleitung

SSV

SSV IGW/100 Anwendungshandbuch

SSV

SSV IGW/935 Bedienungsanleitung

SSV

SSV IGW/922 Bedienungsanleitung

SSV

SSV RMG/941L Bedienungsanleitung

SSV

SSV IGW/920 Bedienungsanleitung

SSV

SSV IGW/935 Bedienungsanleitung

SSV

SSV IGW/925-W Anwendungshandbuch

SSV

SSV IGW/910 Anwendungshandbuch

SSV

SSV IGW/936A Benutzerhandbuch

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung