ST STLINK-V3PWR Bedienungsanleitung
Introduction
STLINK-V3PWR is a two-in-one standalone debugger probe and a source measurement unit (SMU) designed to synchronize
code execution with a power consumption of STM32 applications in real time. This tool is specifically adapted for power
consumption optimization (patent pending).
STLINK-V3PWR can be used as a standalone source measurement unit to supply power and measure the current consumption
of the target application. The product keeps the output voltage constant during fast current transient from very low current to
high current.
STLINK-V3PWR is also a standalone debugging and programming probe for STM32 microcontrollers. The product embeds a
multi-path bridge interface with an integrated level shifter to adapt to the target application I/Os voltage.
STLINK-V3PWR USB Type-C® connector allows data communication with the host PC and sinks up to 5 V/3 A to supply both
the probe and the target application, via the SMU and the auxiliary output.
Figure 1. STLINK-V3PWR top, bottom, and cable views
Picture is not contractual.
Source measurement unit (SMU) and debugger/programmer for
STM32 microcontrollers
UM3097
User manual
UM3097 - Rev 1 - March 2023
For further information contact your local STMicroelectronics sales office. www.st.com
1Features
• 1‑Quadrant source measurement unit with high resolution, and measurement flexibility:
–Programmable voltage source from 1.6 to 3.6 V
– Output current rating 500 mA with overcurrent protection (OCP) at 550 mA
– Programmable sampling rate from 1 SPS to 100 kSPS
– Dynamic measurement:
◦ 100 nA to 500 mA current / 160 nW to 1.65 W power measurements
◦ 50 kHz bandwidth / 1.6 MHz acquisition / 2% accuracy
◦ Compatible with EEMBC® ULPMark™ tests
• Auxiliary output voltage source from 1.6 to 3.6 V under up to 2 A (no current measurement, OCP at 2.5 A)
• Debugging of embedded applications:
– JTAG / Serial Wire Debug (SWD):
◦ SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 10 MHz
◦ JTAG communication support up to 20 MHz
– UART interface on Virtual COM port (VCP) with frequency up to 12 MHz
– Multi-path bridge USB to SPI/I2C/CAN/GPIOs
– Integrated level shifter I/O voltage 1.6 to 3.6V adaptable
• Four bi-color LEDs providing probe state
• Three STDC14 to MIPI10 / STDC14 / MIPI20 flat cables with 1.27 mm pitch connectors
• Four cables (two male/male and two male/female)
• USB Type-C® connector:
– Powered through USB Type-C® (5 V/1.5 A minimum)
– USB 2.0 high‑speed interface
– Probe firmware update through USB
• Direct support from STM32CubeMonitor-Power software tool
UM3097
Features
UM3097 - Rev 1 page 2/30
2Ordering information
To order the STLINK-V3PWR SMU and in-circuit debugger/programmer for STM32, refer to Table 1.
Table 1. Ordering information
Order code Reference Description
STLINK-V3PWR STLINK-V3PWR Debug board for STM32 microcontrollers including
simultaneous current measurement
UM3097
Ordering information
UM3097 - Rev 1 page 3/30
3Development environment
STLINK-V3PWR runs with an STM32 32‑bit microcontroller based on the Arm® Cortex®-M core.
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
3.1 System requirements
• Multi‑OS support: Windows® 10 or beyond, Linux® 64-bit, or macOS®
•USB Type-A or USB Type-C® to USB Type-C® cable
Note: macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux® is a registered trademark of Linus Torvalds.
Windows is a trademark of the Microsoft group of companies.
3.2 Development toolchains
• IAR Systems® - IAR Embedded Workbench®(1)
• Keil® - MDK-ARM(1)
• STMicroelectronics - STM32CubeIDE
1. On Windows® only.
3.3 Toolchain versions
Table 2. Glossary
Toolchain Description Minimum version
STM32CubeProgrammer ST programming tool for ST microcontrollers 1.12.0
IAR Systems® EWARM Third-party debugger for STM32 including current
measurement support 9.32.2
Keil® MDK‑ARM Third-party debugger for STM32 including current
measurement support 5.38
STM32CubeMonitor-Power ST monitoring tool for power consumption 1.2.0
STM32CubeIDE ST debugger for STM32 1.12.0
STLINK-V3-BRIDGE ST software package: C++ API compatible with the bridge
interface of STLINK-V3 and STLINK-V3PWR 1.1.0
3.4 Drivers and firmware upgrade
The driver installation is not mandatory since Windows® 10 but allocates an ST‑specific name to the ST-LINK
COM port in the system device manager. For details information regarding the ST-LINK USB driver, refer to the
technical note Overview of ST-LINK derivatives (TN1235).
STLINK-V3PWR embeds a firmware upgrade (stsw-link007) mechanism through the USB port. As the firmware
might evolve during the lifetime of the STLINK-V3PWR product, to add new functionalities, fix bugs, and support
new microcontroller families, it is recommended to visit the www.st.com website before starting to use STLINK-
V3PWR and periodically, to stay up to date with the latest firmware version. For details information about firmware
upgrades, refer to the technical note Overview of ST-LINK derivatives (TN1235).
UM3097
Development environment
UM3097 - Rev 1 page 4/30
4Glossary
Table 3. Glossary
Term Meaning
AUX Auxiliary output voltage
Target application Target product application embedding an STM32 MCU with peripherals
GND Ground
OCP Over current protection
OUT Main output voltage
OVP Over voltage protection
SMPS Switched‑mode power supply
SMU Source measure unit
UM3097
Glossary
UM3097 - Rev 1 page 5/30
5Product information
5.1 Product content
The STLINK-V3PWR kit contains:
•STLINK-V3PWR probe
• Four wires:
– Two wires male/male (red and black)
– Two wire male/female (red and black)
• Three debug cables allowing the connection from the STDC14 (DEBUG port) to:
– STDC14 connector (1.27 mm pitch) Samtec FFSD-07-D-05.90-01-N
– MIPI10/ARM10-compatible connector (1.27 mm pitch) Samtec FFSD-05/07-D-05.90-01-N
– MIPI20/ARM20-compatible connector (1.27 mm pitch) Samtec FFSD-10/07-D-05.90-01-N
Note: To support the JTAG interface, in 2.54 mm pitch, use a dedicated dongle MIPI/ARM20 to JTAG (2.54 mm) (for
example: dongle “JTAG 20 Pin 2.54 mm to 10 Pin 1.27 mm adapter”)
5.2 STLINK-V3PWR connectors and LEDs identification
This section aims to identify the location of the STLINK-V3PWR connectors and LEDs.
They are illustrated with the silkscreen on the casing serving as a functional reference for most connectors. A
connection overview is given here:
•USB-C: USB Type-C® receptacle for host PC connection using a USB Type-C® to USB Type-C® cable for
the STLINK-V3PWR power supply and data transfer. Refer to Section 5.3 USB connection with a host PC.
•DEBUG: STDC14 2x7-pin male connector with 1.27 mm pitch for connection to an STM32 target
application for debugging operations. Three different flat cables are included in the packaging to connect
with standard connectors MIPI10/ARM 10, STDC14, and ARM 20. Refer to Section 9.3 DEBUG (STM32
JTAG/SWD and VCP).
•BRIDGE: 2x11-pin male connector with 2.54 mm pitch for connection to an STM32 target application for
data communication (typically STM32’s bootloader) with several common interfaces via a proprietary USB
interface. Refer to Section 9.4 BRIDGE (I2C, CAN, SPI, UART, and GPIO).
•POWER: 3-pin screw connector with a 5 mm pitch allows supplying the target application via two
independent programmable power source: OUT (refer to Section 7.2 SMU output (OUT)) and AUX (refer
to Section 7.3 Auxiliary power source output (AUX)).
•LEDs: 4x3-colors LED to indicate the state of the product. Refer to Section 7.6 LEDs management.
UM3097
Product information
UM3097 - Rev 1 page 6/30
Figure 2. STLINK-V3PWR connections
DT59112V1
DEBUG
POWER
BRIDGE
LEDs
USB-C
Note: USB-C, DEBUG, BRIDGE, POWER connectors, and LED terminologies used in this document are referring to
the naming defined in Figure 2.
5.3 USB connection with a host PC
5.3.1 Pre‑requisite
The STLINK-V3PWR’s USB-C must be connected to a USB Type-A host PC or hub port supporting charging
(having a “spark” logo) or to a USB Type-C® host PC or hub port. Refer to Table 4 for details.
The USB LED indicates if STLINK-V3PWR is connected to a USB port supporting charging:
• USB LED in green color: The USB host port supports charging and the STLINK-V3PWR SMU (OUT) and
auxiliary output (AUX) are enabled.
• USB LED in orange color: The USB host port does not support charging and the STLINK-V3PWR SMU
(OUT) and auxiliary output (AUX) are disabled.
Note: The debugger and bridges interfaces are always functional even if the STLINK-V3PWR’s USB-C is connected
onto a standard USB HS (high
‑
speed) host port.
5.3.2 Detailed description
For the data interface, the STLINK-V3PWR’s USB-C must be connected to a USB HS host port. USB FS (full
speed) or USB LS (low speed) modes are not supported. Connecting STLINK-V3PWR to a USB SS (super
speed) host port is also possible as the USB SS port runs in HS mode.
For the power, the STLINK-V3PWR internal circuitry, including the SMU output (OUT), and the auxiliary output
(AUX) are powered by USB-C. Accordingly, the host PC must be capable to supply them, especially for the SMU
output (OUT) and the auxiliary output (AUX) that can require a significant peak of energy to power supply a
complete target application.
STLINK-V3PWR automatically detects the power budget advertised by the host PC USB port. As mentioned in
Section 5.3.1, the STLINK-V3PWR’s USB-C must be connected to a USB host PC or USB hub port that can
provide 5 V/1.5 A minimum, typically a USB host port supporting charging. Refer to Table 4 for details.
UM3097
USB connection with a host PC
UM3097 - Rev 1 page 7/30
Table 4. USB host PC or hub port identification
USB host port Port identification STLINK-V3PWR compatibility USB LED
color
Standard USB Type-A port (500 mA) OUT and AUX disabled orange
Charging USB Type-A port (1.5 A) OK green
USB Type-C®(1) port (1.5 or 3 A) OK green
Charging USB Type-C® port (3 A) OK green
1. Some USB Type-C® ports without the “spark” logo might be advertised as 500 mA ports. In that case, STLINK-V3PWR
works with the OUT and AUX disabled and the USB LED lights in orange color.
Note: Connection to a USB charger is not a functional use case for STLINK-V3PWR. In that case, USB LED lights
in green color (valid power source) and COM LED blinks red color (waiting for USB enumeration). Refer to
Section 7.6 LEDs management.
5.4 Mechanical information
Figure 3. Product dimensions
DT59117V1
90 mm
20 mm
70 mm
5.5 Thermal recommendation
STLINK-V3PWR is recommended to operate at the temperature range specified in Table 11.
STLINK-V3PWR uses precision components that are affected by temperature changes. It is recommended to use
it at a place where the thermal gradient or airflow is minimum. A typical laboratory bench or table might be an
optimal location.
Accordingly, airflow cooling holes on the top and the bottom of STLINK-V3PWR must be kept free to ease air
cooling.
Hence it is recommended to start the measurement after waiting for a few minutes after the product is plugged
into the USB port and a connection is established. This ensures the entire product self‑heating to reach
thermal equilibrium and avoid triggering a self‑calibration sequence during measurement acquisition (refer to
Section 7.2.3 Self‑calibration management).
5.6 Known limitation
The STLINK-V3PWR internal acquisition circuitry is sensitive to vibration and shock. If vibration or shock occurs
during acquisition, STLINK-V3PWR sends acquisition data containing erroneous peak current.
UM3097
Mechanical information
UM3097 - Rev 1 page 8/30
6Quick start
This section describes how to start with STLINK-V3PWR to make power measurements:
1. Check that the bundle is complete (STLINK-V3PWR with three flat cables and a bundle of four wire
jumpers).
2. Install or update the power measurement software (for example STM32CubeMonitor-Power).
3. Connect a USB Type-C® to USB Type-C® cable (recommended) or USB Type-A to USB Type-C® cable
between STLINK-V3PWR and the PC (refer to Section 5.3 USB connection with a host PC).
4. Check the LED status:
– The USB LED must turn green: STLINK-V3PWR is supplied by a valid power source from PC.
– The COM LED must turn red: STLINK-V3PWR debugger is ready.
5. Hardware configuration for power measurement: Connect the STLINK-V3PWR’s SMU (OUT and GND)
onto the power supply input of the target application using wire jumpers. Refer to Section 6.1 Typical
application.
6. Software configuration for power measurement: Refer to Section 6.2 Software configuration.
6.1 Typical application
6.1.1 Connection with a target application for power measurements
STLINK-V3PWR provides two voltage‑regulated power sources: OUT and AUX:
•OUT is a programmable voltage‑regulated power source including current measurement: Refer to
Section 7.2 SMU output (OUT).
• AUX is a programmable voltage‑regulated power source only: Refer to Section 7.3 Auxiliary power source
output (AUX).
Figure 4 provides a basic connection example of STLINK-V3PWR with a target application.
Figure 4. STLINK-V3PWR connection
DT59118V1
VDD
Peripherals
Target
application
optional
+3V3 VDD
3V3_PERIPH
DEBUG
debug I/F
ctrl I/F
GND
• Connect OUT to the target application power supply input to be measured (for example pin +3V3 of an
STM32 Nucleo board) using a wire jumper provided in the kit.
•Connect the GND to the target application ground (for example pin GND of an STM32 Nucleo board) using
a wire jumper provided in the kit.
• (Optional) Connect the AUX power source to the target application input power supply that does not require
to be measured.
6.1.2 Recommendations for power measurements
The use of wire jumpers provided in the kit must be limited to target applications not consuming more than
100 mA to avoid voltage drop through wire jumper cables.
UM3097
Quick start
UM3097 - Rev 1 page 9/30
For target applications having significant current consumption, it is recommended to use cables with adapted
conductor diameter to limit voltage drop through the cable due to wire resistance and current consumption of the
target application.
In addition, it is recommended to not use wires longer than ~30 cm and twist them (OUT and GND wires) to
reduce parasitic inductance.
6.2 Software configuration
1. Launch the STM32CubeMonitor-Power application.
2. Select the COM port of the device.
Figure 5. STM32CubeMonitor-Power setting
3. Click on the "TAKE CONTROL" button to handle the STLINK-V3PWR probe.
– ACQUISITION & REPLAY:
– Set "Sampling Frequency" to 20000 Hz [recommended value]
– Set "Acquisition Time" to 10 s
– Set "Current Threshold" to 1000 µA
– Set "Trigger Source" to "sw" (software)
– Set "Trigger Delay" to 1ms
– Set the desired "Input Voltage" of the target application inside the range 1600 mV/3600 mV
4. Click on the "START ACQUISITION" button
5. The STLINK-V3PWR's SMU turns on and current measurement acquisition starts:
– OUT and AUX LEDs turn on green (output voltage turned on)
– Current measurement is displayed in real time in the STM32CubeMonitor-Power main window.
Note: Refer to the user manual STM32CubeMonitor-Power software tool for power and ultra-low-power
measurements (UM2202).
UM3097
Software configuration
UM3097 - Rev 1 page 10/30
Inhaltsverzeichnis
Andere ST Computerhardware Handbücher
ST
ST STEVAL-IPFC02V1 Bedienungsanleitung
ST
ST X-NUCLEO-IHM12A1 Bedienungsanleitung
ST
ST EVSPIN958 Bedienungsanleitung
ST
ST X-NUCLEO-S2915A1 Bedienungsanleitung
ST
ST AN5717 Montage- und Bedienungsanleitung
ST
ST EVAL6470H-DISC Bedienungsanleitung
ST
ST MB467 Bedienungsanleitung
ST
ST STDES-65ACFADP Technisches Datenblatt
ST
ST UM0501 Bedienungsanleitung
ST
ST X-NUCLEO-OUT02A1 Bedienungsanleitung
ST
ST UM3019 Bedienungsanleitung
ST
ST FP-ATR-BLE1 Bedienungsanleitung
ST
ST X-NUCLEO-OUT09A1 Bedienungsanleitung
ST
ST X-NUCLEO-53L1A1 Bedienungsanleitung
ST
ST STMPE811 Technisches Datenblatt
ST
ST X-NUCLEO-IDB05A2 Bedienungsanleitung
ST
ST STEVAL-IFP043V1 Bedienungsanleitung
ST
ST FP-LIT-BLEMESH1 Bedienungsanleitung
ST
ST UM1472 Bedienungsanleitung
ST
ST STEVAL-OET005 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
