ST X-NUCLEO-OUT10A1 Bedienungsanleitung

Introduction

The X-NUCLEO-OUT10A1 industrial digital output expansion board for STM32 Nucleo provides an affordable and easy-to-use

solution for the development of 0.5 A (typ.) digital output modules, letting you easily evaluate the IPS161HF driving and

diagnostic capabilities with industrial loads.

The X-NUCLEO-OUT10A1 interfaces with the microcontroller on the STM32 Nucleo via 3 kV optocouplers driven by GPIO pins

and Arduino™ UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors.

The expansion board should be connected to either a NUCLEO-F401RE or NUCLEO-G431RB development board, and can be

stacked with another X-NUCLEO-OUT10A1 or an X-NUCLEO-OUT08A1 .

Two X-NUCLEO-OUT10A1 expansion boards allows you to evaluate a dual channel digital output module with 0.5 A (typ.)

capability each, or a 0.5 A (typ.) single channel safety digital output module. In the second scenario, the first shield output is

connected to the supply of the second one. Dedicated on-board hardware can be enabled or disabled to activate fast discharge

of high capacitive loads, output voltage sensing and additional surge pulse output line protection.

Figure 1. X-NUCLEO-OUT10A1 expansion board

Getting started with X-NUCLEO-OUT10A1 industrial digital output expansion

board for STM32 Nucleo

UM2716

User manual

UM2716 - Rev 1 - June 2020

For further information contact your local STMicroelectronics sales office.

www.st.com

1Getting started

1.1 Overview

The X-NUCLEO-OUT10A1 industrial digital output expansion board, embedding the IPS161HF intelligent power

switch (IPS), is designed to meet the application requirement in terms of galvanic isolation between user interface

(or logic side) and power interface (or process side).

This requirement is satisfied by an optical isolation implemented through two couples of optocouplers:

1. The first couple includes:

a. ISO1: for signal forwarding to the device

and

b. ISO2: for diagnostic signal (DIAG pin) feedback

2. The second couple incudes:

a. ISO3: for the additional output voltage feedback signal

and

b. ISO4: for the additional circuitry driving Q1 to allow fast discharge of the output rail

The main features of the X-NUCLEO-OUT10A1 expansion board are:

• Based on IPS161HF single high-side switch with the following main features:

– Operating range up to 60 V/0.7 A

– Low power dissipation (RON(MAX) = 120 mΩ)

– Fast decay for inductive loads

– Open load detection and diagnostics

– Overload and overheating protections with thermal shut-down and cut-off

– PowerSSO-12L package

• Application board operating range: 12 - 33 V, 0 to 0.7 A

• Extended voltage operating range (J1 open) up to 60 V

• Green LED for output ON/OFF status

• Red LED for diagnostics (open load, cut-off and overheating)

• 3 kV galvanic isolation

• Supply rail reverse polarity protection

• Ready for Safety Digital Output Architecture

• EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5

• Wide application development potential in STM32 Nucleo development environment

• Equipped with Arduino™ UNO R3 connectors

• CE certified

• RoHS and China RoHS compliant

1.1.1 Digital section

The digital section is associated with the STM32 interface and digital supply voltage to and from the X-NUCLEO-

OUT10A1 expansion board.

The digital and power sections are isolated by 3.3 mm creepage. Communication between the two sections is

guaranteed by ISO1, ISO2, ISO3 and ISO4 optocouplers.

UM2716

Getting started

UM2716 - Rev 1 page 2/16

Figure 2. X-NUCLEO-OUT10A1 expansion board: digital interface components

The four Arduino® UNO R3 connectors:

• allow expansion board communication with the STM32 Nucleo development board accessing STM32

peripheral and GPIO resources;

• provide digital supply voltage between the STM32 Nucleo development board and the X-NUCLEO-

OUT10A1 expansion board, in either direction.

Normally, the STM32 Nucleo development board supplies the expansion board by 3v3 or 5v0 (JP5 pins 1-2

closed) generated by the USB. You can select the preferred voltage on the expansion board via SW2 (3v3 by

closing pins 1-2; 5v0 by closing pins 2-3).

Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case,

an external supply voltage (7-12 V) should be connected to CN2 connector (not mounted by default) on the

expansion board and the ground loop should be closed by mounting D2 (that enables reverse polarity protection)

or by closing J3 (without reverse polarity).

To supply the VIN voltage rail is necessary to:

• close jumper JP5 between pins 2 and 3 and open jumper JP1 on the NUCLEO-F401RE

• open jumper JP5 between pins 1 and 2 and close jumper JP5 between pins 3 and 4 on the NUCLEO-

G431RB

1.1.2 Power section

The power section involves the power supply voltage (CN1, pin 1 VCC, pin 2 GND), load connection (between

CN1 pin 3 and CN1 pin 2) and electromagnetic compatibility (EMC) protection (U2).

UM2716

Overview

UM2716 - Rev 1 page 3/16

Figure 3. X-NUCLEO-OUT10A1 expansion board: power stage components

For EMC:

• the transient voltage suppressor (U2), enabled by closing J1, is placed between VCC and GND tracks to

protect the IPS161HF against surge discharge on the supply rail path up to ±1 kV/2Ω coupling;

• in common mode surge testing, two single-layer capacitors (C1 and C2 - not included) must be soledered at

the predisposed locations;

• the IPS161HF output stages do not require additional EMC protections with respect to IEC61000-4-2 (± 10

kV contact, ±16 kV air), IEC61000-4-4 (± 4 kV), IEC61000-4-5 (± 3.5 kV) standards.

1.2 Hardware requirements

The X-NUCLEO-OUT10A1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-

G431RB STM32 Nucleo development boards.

To function correctly, the X-NUCLEO-OUT10A1 must be plugged onto the matching Arduino® UNO R3 connector

pins on the STM32 Nucleo board as shown below.

UM2716

Hardware requirements

UM2716 - Rev 1 page 4/16

Figure 4. X-NUCLEO-OUT10A1 and STM32 Nucleo stack

1.3 System requirements

To use the STM32 Nucleo development boards with the X-NUCLEO-OUT10A1 expansion board, you need:

• a Windows PC/laptop (Windows 7 or above)

• a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-

F401RE development board

• a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-

G431RB development board

• the X-CUBE-OUT8 firmware and software package installed on your PC/laptop

1.4 Board setup

Step 1. Connect the X-NUCLEO-OUT10A1 to the NUCLEO-F401RE or NUCLEO-G431RB development board

through the Arduino connectors.

Step 2. Connect the X-NUCLEO-OUT10A1 power section (see Section 1.1.2 Power section).

Step 3. Connect the load between CN1 pins 2 and 3.

Step 4. Connect the mini-USB (for NUCLEO-F401RE) or micro-USB (for NUCLEO-G431RB) cable between

your PC and the STM32 Nucleo board.

Step 5. Download the selected firmware (STSW-OUT8F4 for NUCLEO-F401RE or STSW-OUT8G4 for

NUCLEO-G431RB) onto the microcontroller.

Step 6. Provide the digital supply voltage (see Section 1.1.1 Digital section).

Step 7. Reset the example sequence by pushing the black button on the STM32 Nucleo board.

UM2716

System requirements

UM2716 - Rev 1 page 5/16

Step 8. Push the blue button on STM32 Nucleo board to choose among the examples provided in the default

firmware package.

Note: When using two boards stacked (e.g. dual channel digital output or single channel safety digital output

application), you have to move some signal enabler resistors from DEFAULT to ALTERNATE position. You can

refer to the expansion board schematic and/or to the table below (where board 0 mounts all the resistors in their

DEFAULT position).

Table 1. Pin position when using a board stack

Board 0 Board 1

IN1 Nch_DRV DIAG OUT_FB IN1 Nch_DRV DIAG OUT_FB

R101 R102 R103 R104 R111 R134 R112 R131

UM2716

Board setup

UM2716 - Rev 1 page 6/16

2Schematic diagrams

Figure 5. X-NUCLEO-OUT10A1 circuit schematic (1 of 2)

4700pF

R121 100 (N.M.)

EARTH

DIAG

R125 100 (N.M.)

Arduino Connectors

PA9

OUT_FB

OUT1

Nch-DRV

DIAG

R101 100

OUT_FB

DIAG

109

CN5

SSQ-110-04-F-S

Alternate Nucleo Supply

7V - 12V

Nch-DRV

OUT_FB

Nch-DRV

PB5

PC7

ALTERNATE USE

R124 100 (N.M.)

PB0

PC0

PA5

R104 100

IN1

CN9

SSQ-108-04-F-S

IN1

R133 100 (N.M.)

R111 100 (N.M.)

OUT_FB

IN1

Analog supply

8V - 60 V

R103 100

2.2uF

PA1

PB4

PA3

ALTERNATE USE

R102 100

TP9

5001

OUT_FB

VIN

R112 100 (N.M.)

R123 100 (N.M.)

IN1

default open

D2 BAT48 (N.M.)

ALTERNATE USE

DEFAULT

ALTERNATE USE

IN1

47uF (N.M.)

DIAG

CN7

SSQ-119-04-L-D (N.M.)

Nch-DRV

DEFAULT

ALTERNATE USE

TP8

5001

Nch-DRV

ALTERNATE USE

3v3

CN6

SSQ-108-04-F-S

4700pF

D1 STPS1H100A

Nch-DRV

3V3

VCC

GND

SM15T39CA

OUT1

DIAG

PA7

PC1

ALTERNATE USE

5v0

AVDD

IOREF

R122 100 (N.M.)

Morpho Connectors

(N.M.)

R131 100 (N.M.) IN1

default closed

default open

OUT_FB

CN2

Con2

R130 100 (N.M.)

R132 100 (N.M.)

CN1

Con3

PB8

PA10

PA4

PA2

PB9

PA0

PB10

CN8

SSQ-106-04-F-S

PA8

PA6

PB6

(7V-12V NUCLEO supply voltage)

R134 100 (N.M.)

VCC

VIN

ESDA15P60-1U1M (N.M.)

CN10

SSQ-119-04-L-D (N.M.)

DEFAULT

NRST

PB3

UM2716 - Rev 1 page 7/16

UM2716

Schematic diagrams

Figure 6. X-NUCLEO-OUT10A1 circuit schematic (2 of 2)

OUT3 10

R96.8k

R6390

150060VS75000

GND

R15

68k

Vcc_TAB

J14

con8-2x4-strip-male

R42.2K

SW2

con3-strip-male

100nF

27K

1.5k

J13

con8-2x4-strip-male

0.1uF

R161k

ISO1

ACPL-217-50AE

390

TP7

5001

OUT2

3v3

TP3

5001

R227K

VCC

IN1

TDZ6V2J,115

R14

2.2K

DIAG

NC1

VCC

10nF

5v0

TP6

5001

IPS161HF

OUT1

R727K

RED

R12

22k

Vcc2

ISO2

ACPL-217-50AE

R32.2K

BAT41ZFILM

STN2NF10

default: closed

default:

close 1-2

default:

closed

default:

CLOSE 2-3

default:

3-4 = CLOSE

1-2, 5-6, 7-8 = OPEN

default:

closed

default:

open

default:

3-4 = CLOSE

1-2, 5-6, 7-8 = OPEN

default closed

(open load detection = active)

NC2

OUT_FB

1Vcc1

47nF

SW1

con3-strip-male

STPS1H100A

R13

22k

ISO4

ACPL-217-50AE

R11

ISO3

ACPL-217-50AE

CoD

OUT1

Nch-DRV

OUT4

TR3

SM15T10AY

DIAG

OUT1

VCC

R10

6.8k

UM2716 - Rev 1 page 8/16

UM2716

Schematic diagrams

3Bill of materials

Table 2. X-NUCLEO-OUT10A1 bill of materials

Item Q.ty Ref. Value Description Manufacturer Order code

1 0 C1 , C2 4700 pF 1825 (4564 Metric) 3000

V (3kV) ±10%

Ceramic

capacitors (not

mounted)

Vishay Vitramon HV1825Y472KXHATHV

2 1 C3 2.2 µF SMD 1206 (3216 Metric)

100 V Ceramic capacitor AVX 12061C225KAT2A

3 1 C4 100 nF SMD 0805 (2012 Metric)

100 V Ceramic capacitor Wurth Electronics

Inc. 885012207128

4 1 C5 10 nF 10000 PF X7R 0603 (1608

Metric) 50 V ±10% Ceramic capacitor Wurth Electronics

Inc. 885382206002

5 1 C6 47 nF X7R 0603 (1608 Metric) 50

V ±10% Ceramic capacitor Wurth Electronics

Inc. 885012206093

6 1 C7 0.1 µF X7R 0603 (1608 Metric) 50

V ±10% Ceramic capacitor Wurth Electronics

Inc. 885012206095

7 0 C8 47 µF radial, Can 100 V ±20% Ceramic capacitor

(not mounted)

Wurth Electronics

Inc. 860040875002

8 1 CN1 Con3 10.5X7.4 pitch 3.5 mm Terminal block Wurth Electronics

Inc. 691214110003

9 0 CN2 Con2 7.4X7 pitch 3.5 mm Terminal block (not

mounted)

Wurth Electronics

Inc. 691214110002

10 1 CN5 SSQ-110-04-F-S Connector Samtec Inc. SSQ-110-04-F-S

11 2 CN6, CN9 SSQ-108-04-F-S Connectors Samtec Inc. SSQ-108-04-F-S

12 0 CN7,

CN10 SSQ-119-04-L-D Connectors Samtec Inc. SSQ-119-04-L-D

13 1 CN8 SSQ-106-04-F-S Connector Samtec Inc. SSQ-106-04-F-S

14 2 D1, D7 DO-214AC, SMA 1 A 100 V Power Schottky

rectifier ST STPS1H100A

15 0 D2 SOD-323F, SC-90

Axial general

purpose ginal

Schottky diode

(not mounted)

ST BAT48JFILM

16 1 D3 SOD-123 1 V @ 200 mA (DC)

Surface mount

general purpose

ginal Schottky

diode

ST BAT41ZFILM

17 1 D5 SMD 0603 (1608 Metric) 20 mA Red LED Wurth Electronics

Inc. 150060RS75000

18 1 D6 SMD 0603 (1608 Metric) 20 mA Green LED Wurth Electronics

Inc. 150060VS75000

19 1 D8 SMD, SOD-323F, SC-90 6.2 V

500 mA 500 mW Zener diode Nexperia USA

Inc. TDZ6V2J,115

20 4

ISO1,

ISO2,

ISO3,

ISO4

3KV, ACPL-217-50AE 4-SOIC

(0.173", 4.40 mm width) Optocouplers Broadcom Limited ACPL-217-50AE

21 8

J1, J2, J4,

J5, J7, J8,

con2-strip-male Jumpers Any Any

UM2716

Bill of materials

UM2716 - Rev 1 page 9/16

Item Q.ty Ref. Value Description Manufacturer Order code

21a 0 J3 con2-strip-male Jumpers (not

mounted) Any Any

22 2 J13, J14 con8-2x4-strip-male pitch 2.54

mm Connector headers Wurth Electronics

Inc. 61300821121

23 1 Q1 TO-261-4, TO-261AA 100 V 3.3 W

(Tc)

StripFET power

MOSFET in

SOT-223 package

ST STN2NF10

24 2 R1, R2 SMD 27 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-0727KL

25 2 R3, R4 SMD 2.2 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-072K2L

26 2 R5, R6 SMD 390 Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-07390RL

27 1 R7 SMD 27 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-0727KL

28 1 R8 SMD 1.5 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-071K5L

29 2 R9, R10 SMD 6.8 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-076K8L

30 1 R11 SMD, 1 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-071KL

31 2 R12, R13 SMD, 22 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-0722KL

32 1 R14 SMD, 2.2 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-072K2L

33 1 R15 SMD, 68 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-0768KL

34 1 R16 SMD, 1 K Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistor Yageo RC0603FR-071KL

35 4

R101,

R102,

R103,

R104

SMD, 100 Ohm 0603 (1608

Metric), 0.1 W, 1/10 W ±1% Resistors Yageo RC0603FR-07100RP

36 0

R111,

R112,

R121,

R122,

R123,

R124,

R125,

R130,

R131,

R132,

R133,

R134

100 Ohm, SMD, 0603 (1608

Metric), 0.1 W, 1/10 W ±1%

Resistors (not

mounted) Yageo RC0603FR-07100RP

37 2 SW1,

SW2 con3-strip-male Connection

headers Wurth 61300311121

38 5

TP3, TP6,

TP7, TP8,

TP9

5001 0.100" Dia x 0.180" L (2.54

mm x 4.57 mm) Test points Keystone

Electronics 5001

39 1 TR3 DO-214AB, SMC 1500W (1.5 kW) Automotive 1500

W TVS in SMC ST SM15T10AY

40 1 U1 PowerSSO12 Exposed Pad IC power switch ST IPS161HF

UM2716

Bill of materials

UM2716 - Rev 1 page 10/16

Inhaltsverzeichnis

Andere ST Computerhardware Handbücher

ST STM32F3DISCOVERY Bedienungsanleitung

ST STA309A Bedienungsanleitung

ST X-NUCLEO-IKS4A1 Bedienungsanleitung

ST AN1235 Montage- und Bedienungsanleitung

ST X-NUCLEO-NFC03A1 Stücklistenhandbuch

ST X-NUCLEO-OUT07A1 Bedienungsanleitung

ST STM32F107Series Bedienungsanleitung

ST STM32U575 Series Montage- und Bedienungsanleitung

ST X-CUBE-SBSFU Bedienungsanleitung

ST X-NUCLEO-GFX02Z1 Bedienungsanleitung

ST TIP120 Bedienungsanleitung

ST STEVAL-IFP043V1 Bedienungsanleitung

ST STEVAL-CCH002V2 Bedienungsanleitung

ST TIP122FP Bedienungsanleitung

ST X-NUCLEO-IDW04A1 Bedienungsanleitung

ST X-NUCLEO-IHM09M2 Bedienungsanleitung

ST STM32U5 Bedienungsanleitung

ST X-NUCLEO-OUT01A2 Bedienungsanleitung

ST STMPE811 Technisches Datenblatt

ST STR9 Bedienungsanleitung

ST STDES-65ACFADP Technisches Datenblatt

ST STM32F411 Bedienungsanleitung

ST STM32 Nucleo Bedienungsanleitung

ST X-NUCLEO-STMODA1 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung