ST UM1789 Bedienungsanleitung
September 2014 DocID026531 Rev 1 1/10
UM1789
User manual
STEVAL-IDB003V1 evaluation board
quick start guide
Introduction
The STEVAL-IDB003V1 is an evaluation board based on BlueNRG, a low power Bluetooth
®
Smart IC that is compliant with the Bluetooth
®
v4.0 specification and supports both master
and slave roles.
The STEVAL-IDB003V1 platform features an on-board STM32L low power microcontroller.
It can be used to explore the BlueNRG features and as a development platform for
Bluetooth
®
Smart applications running on the STM32L microcontroller and interfacing to the
BlueNRG network coprocessor.
Figure 1. STEVAL-IDB003V1 Bluetooth
®
Smart platform
*63*6*
www.st.com
Contents UM1789
2/10 DocID026531 Rev 1
Contents
1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Install BlueNRG DK SW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Insert the STEVAL-IDB003V1 board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Open the BlueNRG GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 SW demonstration applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 List of acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DocID026531 Rev 1 3/10
UM1789 Getting started
10
1 Getting started
The STEVAL-IDB003V1 evaluation board is preprogrammed with a software
(BlueNRG_VOM_x_x.hex) allowing users to run the BlueNRG PC GUI (graphical user
interface), which can be used to interact and evaluate the capabilities of the BlueNRG
network processor.
To configure the STEVAL-IDB003V1 platform and run the preprogrammed software and
associated BlueNRG GUI, follow the instructions below.
1.1 Install BlueNRG DK SW package
•Before using the STEVAL-IDB003V1 platform, download the latestBlueNRG DK software
package available on the STEVAL-IDB003V1 web page (Table 1, STEVAL-IDB003V1
platform)
•Unzip the file, launch the related installer and follow installation steps (default installation
path is C:\Program Files (x86)\STMicroelectronics\BlueNRG DK x.x.x)
•Wait for the package installation to complete.The following folder will be available on the
selected installation path.
Figure 2. BlueNRG DK SW package structure and content
The software package installation procedure will also automatically install the following PC
software drivers available in the PCDriver folder:
•USB DFU PC driver required for supporting device firmware upgrade (DFU) through USB
•USB Virtual COM Port driver required for supporting the USB Virtual COM I/O
communication channels.
1.2 Insert the STEVAL-IDB003V1 board
•Plug the STEVAL-IDB003V1 into a PC USB port: Windows’ new hardware wizard will
appear.
•Wait for the device recognition process to complete: in Computer, Manage, Device
Manager, Ports (COM & LPT area), a new STMicroelectronics Virtual COM Port will
appear.
*63*6*
Getting started UM1789
4/10 DocID026531 Rev 1
Figure 3. STEVAL-IDB003V1 Virtual COM Port
1.3 Open the BlueNRG GUI
The BlueNRG GUI is available in the BlueNRG DK software package, Application folder
(Figure 2: BlueNRG DK SW package structure and content):
•Launch the BLUENRG_GUI.exe file
•Select the COMxx port associated to the STEVAL-IDB003V1 platform
•Click on Open tab: the BlueNRG GUI is now ready to use
*63*6*
DocID026531 Rev 1 5/10
UM1789 Getting started
10
Figure 4. BlueNRG GUI
The BlueNRG GUI utility can send standard and vendor-specific HCI commands to the
BlueNRG network coprocessor and receive events from it. It allows the user to configure
each field of the HCI command packets to be sent and analyze all received packets.
Note: For more information on the BlueNRG GUI capabilities and available utilities, refer to
Table 1 (UM1686 user manual).
GSPG1006141045SG
SW demonstration applications UM1789
6/10 DocID026531 Rev 1
2 SW demonstration applications
In order to develop a software application for the STEVAL-IDB003V1 platform, it is
recommend to start with the reference demonstration applications provided within the
BlueNRG DK software package, in the Projects folder (Figure 2). The IAR Embedded
Workbench for ARM (EWARM) tool V6.60 is needed to build software applications running
on the STM32L microcontroller.
Pre-built STM32L microcontroller binary images for the reference demonstrations are
already available in the BlueNRG DK software package, in the Firmware folder (Figure 2).
To download an STM32L binary image, apply the following DFU procedure:
•Open the BlueNRG GUI
•Press and hold the STEVAL-IDB003V1 platform SW1 button
•Plug the STEVAL-IDB003V1 board into a PC USB port
– The orange LED D3 will start to blink: STM32L device is in DFU mode, allowing it
to upgrade its Flash image through USB interface.
•From the BlueNRG GUI, select Tools, Flash Motherboard FW and follow the indications
to select the new binary application image to be downloaded into the STM32L Flash.
•Wait for the DFU download process to complete.
Figure 5. BlueNRG GUI DFU procedure
Note: For a description of the available BlueNRG demonstration applications and supported
platforms, refer to Table 1 (UM1686 user manual).
The BlueNRG_COM_x.x.hex binary is also provided within the BlueNRG DK software
package, in the Firmware folder (Figure 2: BlueNRG DK SW package structure and
content). The user can reload it through the previously described DFU procedure.
*63*6*
DocID026531 Rev 1 7/10
UM1789 References
10
3 References
Table 1. Reference information
What Where Description
BlueNRG
Bluetooth
Low Energy
wireless
network
processor
www.st.com/bluenrg BlueNRG device
web page
BlueNRG DK
SW package http://www.st.com/web/en/catalog/tools/PF259737#
BlueNRG SW
package with
BlueNRG GUI &
reference
demonstration
applications
Bluetooth
Low Energy
Specification https://www.bluetooth.org/en-us/specification/adopted-specifications
Bluetooth Low
Energy
specification web
page
STEVAL-
IDB003V1 http://www.st.com/web/en/catalog/tools/PF260386
STEVAL-
IDB003V1
platform web
page
UM1686 user
manual http://www.st.com/st-web-
ui/static/active/en/resource/technical/document/user_manual/DM00099259.pdf
BlueNRG
development kit
user manual
describing
BlueNRG GUI
andthereference
demonstration
applications
List of acronyms UM1789
8/10 DocID026531 Rev 1
4 List of acronyms
Table 2. List of acronyms used in the document
Term Meaning
BLE Bluetooth Low Energy
DFU Device firmware upgrade
DK Development kit
GUI Graphical user interface
HCI Host controller interface
SW Software
USB Universal serial bus
DocID026531 Rev 1 9/10
UM1789 Revision history
10
5 Revision history
Table 3. Document revision history
Date Revision Changes
29-Sep-2014 1 Initial release.
UM1789
10/10 DocID026531 Rev 1
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2014 STMicroelectronics – All rights reserved
Inhaltsverzeichnis
Andere ST Hauptplatine Handbücher
ST
ST STM3210C-EVAL Bedienungsanleitung
ST
ST STM8L15LPBOARD Bedienungsanleitung
ST
ST SPC58XXADPT144S REV.B Bedienungsanleitung
ST
ST STM32439I-EVAL Bedienungsanleitung
ST
ST STM32U5 Bedienungsanleitung
ST
ST STEVAL-OET001V1-LCP154DJF Bedienungsanleitung
ST
ST STEVAL-MKI132V1 Bedienungsanleitung
ST
ST AN3959 Montage- und Bedienungsanleitung
ST
ST STR730-EVAL Bedienungsanleitung
ST
ST STEVAL-BLUEMIC-1 Bedienungsanleitung
ST
ST STM32CubeF4 Bedienungsanleitung
ST
ST Nucleo STM32F302R8 Bedienungsanleitung
ST
ST EVALCOMMBOARD Bedienungsanleitung
ST
ST STEVAL-USBPD45H Bedienungsanleitung
ST
ST STM32L152-EVAL Montage- und Bedienungsanleitung
ST
ST SPC58NHADPT386S Bedienungsanleitung
ST
ST AEK-POW-LDOV01J Bedienungsanleitung
ST
ST STM32CubeH7 Bedienungsanleitung
ST
ST X-NUCLEO-S2868A1 Bedienungsanleitung
ST
ST STM32L5 Nucleo-144 board Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
