Stagg ECOPAR2 Bedienungsanleitung

User Manual

ECOPAR2

SLI-ECOPAR2

Table of Contents

1.BEFORE USAGE

This package contains

Unpacking

Introduction

Specifications

Features

2.INSTALLATION

Power Connection

DMX 512 Connection

3. OPERATION

Control panel Function

Menu Map

Operating Instructions

DMX Channels

1.BEFORE USAGE

This package contains

•1x EcoPar 2

•1x Power Cable

•1x User Manual

Unpacking

•Thank you for purchasing this product, it has been thoroughly tested

and has been shipped in perfect operating condition.

•Carefully check the packaging for damage that may have occurred during

shipping.

•If the packaging appears to be damaged, carefully inspect your fixture

for any damage and be sure all equipment necessary to operate the unit has

arrived intact.

•If damage has been found or parts are missing, please contact your vendor or

our customer support number for further instructions.

Introduction

•This fixture can operate in six different operating modes: DMX control, sound

active, automatic, manual setup, infrared remote control or in a Master/Slave

configuration

•This product comes with several built-in programs that can be used while

operating as a single unit or with multiple units linked in a master/slave

configuration

•For best results use fog or special effects smoke to enhance the beam

projection

•Warning! To prevent or reduce the risk of electrical shock or fire, do not

expose this unit to rain or moisture.

•Warning! This product may cause severe eye damage. Avoid looking directly

into the light source at all times!

Specifications

•Voltage:AC100V～240V, 50-60Hz

•Power Consumption: 40W

•Light source: 5x 8W RGBW 4 in 1 LED

•Beam angle:25°

•Max output @1m: 5600 Lux

•DMX channels: 1/2/3/4/5/6/7/8 DMX Channels

•Packing Dimensions: 210x210x140mm

•Net weight: 1,0 Kg

•Gross weight: 1,2Kg

Features

•3PIN XLR DMX in and out

•IEC power in and out

•6control modes: DMX512, automatic programs, sound control, mast/slave,

manual setup and infrared remote control

•LCD display for easy setup

•Indoor operation temperature range: -20°C～+40°C

•Dimmer: 0-100%

Please Note: Specifications and improvements in the design of this unit and this

manual are subject to change without any prior written notice.

2.INSTALLATION

Installation requirements

•The product can be hung or placed on a solid surface with the double

mounting brackets

•If you install the light in a hanging position, always use a suitable mounting

position and a clamp or screw that is strong enough to hold the product

without stress. Always use a safety wire to secure the light.

•Always keep a distance of minimum 0.5m to all objects or persons

•Installation should always be done by a trained professional.

•Make sure the light always has good ventilation

•It is recommended to always use 110 Ohm DMX cable to prevent data

corruption of your DMX control signal

Power connection

The equipment has an auto-switching power supply that can accommodate a

wide range of input voltages. The only thing necessary to do before powering on

the unit is to make sure the line voltage you are applying is within the range of

accepted voltages. This equipment will accommodate between 100V and 240v

AC 50-60HZ. It is possible to daisy chain the power connection from one fixture

to the next. We recommend not connecting more than 30 fixtures on one 16A

220V socket and not more than 15 fixtures on one 16A 110V socket.

Color

Connection

Brown

AC live wire

Blue

AC zero curve

Green/Yellow

AC ground wire

DMX Serial Data Link

1. Connect the male 3pin DMX input of the first fixture to the female 3pin DMX

output of the lighting controller using 110 Ohm DMX cable, for example a Stagg

Commandor 10 (skip this step when not using a controller)

2. Connect the output of the first fixture to the input of the next fixture using 110

Ohm DMX cable. Repeat this process until you reach your last fixture. Here it is

recommended to connect a DMX terminator to the output of the last fixture in the

chain.

3. OPERATION

Menu Map

Operating Instructions

Addr -DMX Address Setup

•Press MENU, then Up or DOWN until "Addr" is displayed, then press ENTER

•Change the DMX address by pressing UP or DOWN

•Press ENTER to save the DMX address

Auto -Automatic Programs Setup

•Press MENU, then Up or DOWN until "Auto" is displayed, then press ENTER

•"Autx" will now be displayed. Choose your desired program by pressing UP or

DOWN. Press Enter to select the program

•"SPx" will now be displayed. Choose the running speed for the program by

pressing UP or DOWN

Colo -Preset Colors Setup

•Press MENU, then UP or DOWN until "CoLo" is displayed, then press ENTER

•Either “CoL X”, “X” representing a number between 1-9 or “AtF ” will be

displayed. Press UP or DOWN to select a preset color, press ENTER to confirm.

•Select "AtF" and press ENTER to enter "AtF" mode which lets you mix your

own color. Enter the desired amount of Red into "rxxx", press ENTER, the

desired amount of Green into "Gxxx", press ENTER, the desired amount of

Blue into "bxxx", press ENTER. You can adjust the amount with the UP and

DOWN buttons.

Chnd-DMX Channel Modes

•Press MENU, then UP or DOWN until "Chnd" is displayed, then press ENTER

•"X Ch" will now be displayed. "X" represents the DMX mode you have

selected (see DMX channel charts for reference). Choose your desired DMX

mode with UP or DOWN and press ENTER to confirm.

Soun -Sound Control Setup

•"Soun" will now be displayed. Choose your desired Sound Controlled Program

by pressing UP or DOWN. Press Enter to select the program.

•"SouX" will now be displayed, X being a number from 1 to 9. Using UP or

DOWN you can adjust the sensitivity of the internal microphone.

Ir-Enable/Disable Infrared Receiver

•Press MENU, then UP or DOWN until "Ir" is displayed, then press ENTER

•Press UP or DOWN to set the IR receiver to ON or OFF. When ON the unit

can receive commands from the IR-REMOTE, when OFF it can not. This

feature works together with Master/Slave mode, so only the Master fixture

should be set to ON and all the Slave fixtures should be set to OFF

SLav -Master/Slave Setup

•Press MENU, then UP or DOWN until "SLav" is displayed, then press ENTER

•"Sla" will now be displayed. Slave mode is selected for this fixture, it will follow

automatic programs, sound mode and fixed color/atf selection of the Master

fixture it is connected to.

VER -Software Version

•Press MENU, then UP or DOWN until "SLav" is displayed, then press ENTER

•The current software version is displayed, press MENU to exit.

Infrared remote control

Before using the IR Remote, always check the following:

1. Please make sure the battery has sufficient charge, if not replace the battery

2. Please confirm the "Ir" setting in the fixture's menu is set to on.

3. Take into account the remote works best at a distance of 1.5 to 4m

Remote control functions:

1: “BLACK OUT” : Function Exit

2: “DMX” setup of the fixtures DMX address. Press this button, then press "+” or “-”

to increase or decrease between A001-A512. Alternatively you can enter the

address with the numerical keypad (0,1,2,3,4,5,6,7,8,9). The first key press enters

the first number, the second the second number and the third the third number. For

example: A053 = Button 0, then button 5, and then button 3.

3: “SLAVE” : This will put the device in SLAVE mode

4: "AUTO1" & "AUTO2": These 2 buttons are hotkeys to the first two Automatic

Programs in AUTO mode. If you want to select higher programs, use the UP or

DOWN buttons on the remote. You can adjust the run speed with the SPEED button

(explained below)

5: “SOUND1” & “SOUND2: These 2 buttons are hotkeys for the two Sound

Controlled Programs. You can adjust the sensitivity of the microphone with the

SPEED button (explained below)

6: “SPEED”: When the fixture is in AUTO mode, this button will adjust the speed of

the selected program. When the fixture is in SOUND mode, this button will adjust the

sensitivity of the microphone.

7: "R/G/B/W": These buttons can be used to create a user-mixed color. Press R(ed),

G(reen), B(lue) or W(hite) and used UP or DOWN to adjust the level of brightness of

this color. Alternatively, enter a value between 0 and 255 with the numerical buttons.

8: “STROBE”: When using the fixture in manual color mode, this button activates the

strobe function. Using UP or DOWN you can adjust the strobe rate from 0-20Hz.

9: “UP” & “DOWN” : These two buttons are used to adjust various parameters

of the fixture.

10: “0,1,2,3,4,5,6,7,8,9”: These buttons are used to either setup a DMX address or

enter the brightness value when using manual Color Mixing with the R/G/B/W

buttons.

DMX 512 Control

This function allows you to use a universal DMX-512 controller such as the Stagg

COMMANDOR 4 or Stagg COMMANDOR 10 to control the Ecopar 2, a DMX

controller allows you to create unique programs tailored to your individual needs.

The Ecopar 1 uses different DMX channel modes, this will allow you to create

custom lightshows. Follow the instruction on the following DMX address charts.

DMX Channels

1 Channel Mode

Channel

Value

Function

0-15

16-31

32-47

48-63

64-79

80-95

96-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

Color Macros (LED @100%)

OFF

RED

GREEN

BLUE

WHITE

RED & GREEN

RED & BLUE

RED & WHITE

GREEN & BLUE

GREEN & WHITE

BLUE & WHITE

RED & GREEN &BLUE

RED & GREEN &WHITE

RED & BLUE &WHITE

GREEN & BLUE &WHITE

RED & GREEN & BLUE &WHITE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Stagg DJ-Equipment Handbücher

Stagg

Stagg EcoPar36 Bedienungsanleitung

Stagg

Stagg Baryonic 24 Bedienungsanleitung

Stagg

Stagg EcoPar18 Bedienungsanleitung

Stagg

Stagg CITY BEAM Bedienungsanleitung

Stagg

Stagg KINGPAR 5 Bedienungsanleitung

Stagg

Stagg SARI-BARIO1 Bedienungsanleitung

Stagg

Stagg EcoPar186 Bedienungsanleitung

Stagg

Stagg CLASSICPAR 36 Bedienungsanleitung

Stagg

Stagg TRANCE60 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung