Stanley Hugs CGS-HGS-1000 Bedienungsanleitung

User Guide

Hugs®Wi-Fi Tag Charger

iii

Hugs® Wi-Fi Tag Charger User Guide

Table of Contents

Introduction 1

Overview 1

Model Numbers 1

Intended Use 1

Safety Considerations 1

Documentation 1

Orientation 2

General Description 2

Operating and Display Modes 5

Installing the Charger 6

Wall Mounted 6

Setting Up the Charger 7

Using the Charger 8

Inserting the Tag into the Charger 8

Removing the Tag from the Charger 9

Speciﬁc Charging Capabilities 10

Overview 10

Dimensions and Weight 10

Hugs Tags States 11

Hugs Tag Behavior with Sensor Alarm 12

iv Hugs® Wi-Fi Tag Charger User Guide

Maintenance 13

Operational Checks 13

Cleaning Instructions 13

Supplies and Accessories 15

Compliance and Safety 16

Introduction

Hugs® Wi-Fi Tag Charger User Guide

Introduction

Overview

The Hugs on MobileView software notiﬁes the users when the Hugs Tag

battery is getting low. Placing the Hugs Tag in the charger erases all the

history data from the tag, including the Kisses® bonding and the tag

status. It also triggers MobileView to erase the speciﬁc patient admitting

information.

Model Numbers

The Hugs Tag Charger part number:

• CGS-HGS-1000

Based on the power supply outlet type:

• CGS-HGS-1000-U U.S. outlet

• CGS-HGS-1000-E European outlet

• CGS-HGS-1000-J Japanese outlet

• CGS-HGS-1000-UK U.K. Outlet

Intended Use

The Hugs Wi-Fi Tag Charger is intended for facility staff who are using the

Hugs Wi-Fi Tags in conjunction with the MobileView security application.

Safety Considerations

• Position any trailing wires so that they are not a trip hazard and are less

likely to get damaged.

• Check that the plug is not damaged and that the cable is properly

secured with no internal wires visible.

• Where there is evidence that the supply may not be safe, such as

damaged equipment or wiring, the supply should not be used until work

has been done to correct this.

Documentation

Please refer to the following document for technical speciﬁcations for the

Hugs Wi-Fi Tag Charger.

• Hugs Wi-Fi Tag Charger Data Sheet p/n 0971-063-000

Orientation

2Hugs® Wi-Fi Tag Charger User Guide

Orientation

General Description

This section describes the parts and LEDs on the Charger. POWER

SOCKET

ON/OFF

SWITCH

CHARGER

STATUS

CHARGING

LED

CHARGING

METALS

Power Socket

The power socket is located at the top-left side of the Charger. An external

power supply is provided with the Charger. For more information about the

power supply, see “Supplies and Accessories” on page 15.

Orientation

Hugs® Wi-Fi Tag Charger User Guide

Orientation

General Description

This section describes the parts and LEDs on the Charger. POWER

SOCKET

ON/OFF

SWITCH

CHARGER

STATUS

CHARGING

LED

CHARGING

METALS

Power Socket

The power socket is located at the top-left side of the Charger. An external

power supply is provided with the Charger. For more information about the

power supply, see “Supplies and Accessories” on page 15.

ON/OFF Switch

After the Charger is plugged in, press the ON/OFF switch to the ON position.

When the Charger is not being used, press the switch to the OFF position.

Charger Status LED

The Charger status LED is located at the top-right on the front of the

Charger. When the Charger is plugged in and turned on, the Charger status

LED turns YELLOW.

Orientation

4Hugs® Wi-Fi Tag Charger User Guide

Charging LED for Hugs Tag

CHARGING LED:

Yellow when the Hugs Tag

is correctly placed in the

Charger

Each Hugs Tag impression in the Charger has its own charging LED (24

LEDs in total). There are three (3) available colors for the LEDs: GREEN,

YELLOW and RED. For more information about the LED color indications, see

“Operating and Display Modes” on page 5.

Charging Metals

The charging metals are located on either side of the inside of the Hugs Tag

impression. Charging for the Hugs Tag only begins once the charging metals

are in contact with the metal in the tag slots

Orientation

Hugs® Wi-Fi Tag Charger User Guide

Operating and Display Modes

The following table describes the LED indications for the Hugs Tag Charger.

Color Description

GREEN Battery is fully charged.

YELLOW Charging in progress.

RED FLASHING Issue with the Hugs Tag. Remove and replace the tag.

RED SOLID Issue with the Charging slot. It is not necessary to unplug the

Charger. An error may possibly be cleared by switching the

Charger OFF then back ON again. If the issue continues, do not

use the specic Charging slot. Other slots can be used for charging.

Please contact Support.

OFF - NO COLOR LED is does not turn on when the tag is placed in the slot– Remove

the tag and replace it with a dierent tag. If the LED is still o, place

the tag in another charging slot. If the LED is on (GREEN or AMBER) in

the new slot then the problem is with the rst charging slot. Do not

use this slot to charge tags. If the LED in the new charging slot is o

as well, then there is an issue with the tag. Discard the tag.

YELLOW Located near the ON/OFF switch indicating the Charger is ON.

Installing the Charger

6Hugs® Wi-Fi Tag Charger User Guide

Installing the Charger

The following items are included with the Hugs Tag Charger:

• two (2) #6 Philips head screws

• two (2) plastic wall anchors

• Mounting plate

Wall Mounted

1. Establish a location on the wall for the Hugs Tag Charger.

2. Draw two (2) holes on the wall, at a level distance 262 mm apart,

from center to center.

3. Drill two holes at the marked locations on the wall.

4. Insert the plastic wall anchors in the drilled holes.

5. Mount the plate and align the anchor holes with the wall anchors.

6. Using the supplied Philips head screws, securely screw the plate to

the wall.

7. Optionally, use wood screws or other suitable wall mount hardware

in the remaining holes on the plate.

8. Slide the Hugs Tag Charger onto the plate to mount it on the wall.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Stanley Akkuladegerät Handbücher

Stanley

Stanley BC40BS Bedienungsanleitung

Stanley

Stanley BC50BS Bedienungsanleitung

Stanley

Stanley BC1509 Bedienungsanleitung

Stanley

Stanley BC6809 Bedienungsanleitung

Stanley

Stanley BM1S Bedienungsanleitung

Stanley

Stanley fatmax FMC692L Bedienungsanleitung

Stanley

Stanley BM1S Bedienungsanleitung

Stanley

Stanley Re-CHARGEiT 40A Bedienungsanleitung

Stanley

Stanley SXAE00025 Bedienungsanleitung

Stanley

Stanley PPRH5 Bedienungsanleitung

Stanley

Stanley DPS109 Bedienungsanleitung

Stanley

Stanley SXAE00026 Bedienungsanleitung

Stanley

Stanley BC15 Bedienungsanleitung

Stanley

Stanley BC209h284504 Bedienungsanleitung

Stanley

Stanley FATMAX SFMCB14 Bedienungsanleitung

Stanley

Stanley FATMAX BC8S Bedienungsanleitung

Stanley

Stanley GBCPRO Bedienungsanleitung

Stanley

Stanley SC201 Bedienungsanleitung

Stanley

Stanley BC15BS Bedienungsanleitung

Stanley

Stanley BC1509 Bedienungsanleitung

Stanley

Stanley Fat Max SFMCB24 Bedienungsanleitung

Stanley

Stanley PIUSB2S Bedienungsanleitung

Stanley

Stanley BC209 Bedienungsanleitung

Stanley

Stanley Bc8 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung