-20℃to 60℃,
5% to 90%RH(No condensation)
(0℃to 10℃:Max0.5A (Recommendation)*1
SM-L300 ChargingCradle Installation Guide
ϤInformation Ϥ
Battery Charging
ϤWEEE (Waste Electrical and Electric Equipment)
This installation guide provides information required for
product installation and use. Read the following contents
carefully, before using this product.
ϤComponents
ϤPrecautions for Installation and Handling
ϤConnecting the Cables
Charging Cradle
1. Turn the printer o.
2. Slide the printer into the charging
cradle as shown.
3. Place the printer correctly on a
cradle.
4. Charging begins when the printer
is inserted.
5. When charging is complete, pull
out the printer to remove it.
Installation Guide
1. Do not short-circuit at the charging contact part using some
metal parts like clip. This might increase the risk of igniting
and emitting smoke.
2. Be careful to not enter water or any foreign objects into the
charging cradle. This might increase the risk of igniting and
emitting smoke.
3. Do not use this product in places where it is likely to come into
contact with water, oil or other liquids, or in places where there
is a lot of dust or lint in the environment.
4. Avoid placing in direct sunlight and/or locations subject to
excessive heat.
5. Subjecting the product to strong vibration and/or shock can
cause damage.
6. Do not install in unstable and/or non-level locations.
7. Secure sucient space in the installation area to facilitate easy
usage.
8. Do not use or store in locations subject to high temperatures
and/or humidity.
9. Do not use or store in dusty locations.
Charging Cradle LED display and charging status
CAUTION
Use the communication port which certied by USB compliance or
USB charging port.
1. The charging time may vary depending on the type of the charger.
Normally, it takes 5 to 6 hours to charge the battery pack.
2. LED display at full charge is dierent between the printer and the
charging cradle. Please check the LED on the printer to see whe-
ther the charging is complete.
Item
Rated Voltage
Input Voltage
Input Current
Output Current
Operating Condition
Storage Condition
Output No-load Voltage
Specications
5V
4.75V - 5.25V
1.0A MAX
4.75V - 5.25V
1.0A MAX
0℃to 45℃,20% to 85%RH(No condensation)
Charging Condition
This charging cradle is just for charging. (It does not communicate to printer)
*1) When the printer is used in a low temperature environment ( less than 10
degrees), the battery’s performance will be diminished, and the amount
of time that you can use the printer for may be reduced.
0℃to 45℃,20% to 85%RH(No condensation)
NOTE
This marking shown on the product or its literature, indicates that
it should not be disposed of with other household wastes at the
end of its working life.
To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse
of material resources.
Household users should contact either the retailer where they purchased
this product, or their local government oce, for details of where and how
they can take this item for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial
wastes for disposal.
http://www.starmicronics.com/support/
SM-L300 Charging Cradle Installation Guide
This product complies with E-waste (Management) Rules, 2016.
In accordance with the requirement of the EU commission,
The manufacturer is :
Star Micronics Co.,Ltd.
20-10 Nakayoshida, Suruga-ku, Shizuoka-shi,
Shizuoka 422-8654 Japan
The importer is :
Star Micronics Europe Ltd.
Star House, Peregrine Business Park, Gomm Road, High Wycombe,
Bucks. HP13 7DL, U.K.
Note: If battery is always charged even though it is full, the amount
of time that you can use the printer may be reduced.
LED
Red LED
Green LED
No LED
Status
Charging
Fully Charged
Error / No Power
Charging via PC
USB Port
Ferrite Core (Printer Accessory)
USB Cable (Printer Accessory)
Attach a ferrite core to the USB cable.
Refer to section 11.4 of Product Specications.
USB Chager (USB chargers are sold separately.)
USB charger
Mobile battery charger
USB cigar charger etc.
