StarPanel Technologies M3104 Bedienungsanleitung
M3104
Industrial Touch Screen Monitor
User and Calibration Manual
Rev. G (6/09
)
Displays for the Real World
StarPanel Technologies, Inc.
(503) 654
-
6216
e
-
mail: support@starpanel.com
Copyright © 2009
StarPanel Technologies, Inc.
All rights reserved.
All products or brand names are trademarks or registered trademarks of their respective companies.
The information contained in this manual is subject to change without notice.
Document
contains information for StarPanel M3104 monitor.
Printed in the USA
COMPLIANCE STATEMENT
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
T
his Class A digital apparatus complies with Canadian ICES
-
003.
Cet appareil numériqué de la classe A est conformé à la norme NMB
-
003 du
Canada.
Table of Contents
Welcome to the M3104
Industrial Touch Screen Mo
nitor
................................
.............
1
Connecting to the M3104 Monitor
................................
................................
................
1
Power
................................
................................
................................
......................
1
VGA
................................
................................
................................
.........................
1
Serial
................................
................................
................................
.......................
1
General Specifications and System Require
ments
................................
......................
2
Adjustments & Calibration
................................
................................
..............................
3
Using The Control Buttons
................................
................................
...........................
3
Maintenance and Care
................................
................................
................................
.....
4
Backlight
................................
................................
................................
..................
4
Cleanin
g
................................
................................
................................
..................
4
Energy Saving Mode
................................
................................
................................
........
5
Energy Saving Mode
................................
................................
................................
....
5
Touch Screen
................................
................................
................................
...................
6
Service Guide
................................
................................
................................
...................
7
Technical Support
................................
................................
................................
............
8
StarPanel Technologies, Inc. Limited Product Warranty
................................
.............
9
M3104 Industrial Touch Screen Monitor
1
Welcome to the M3104
Industrial Touch Screen Monitor
Thank you for purchasing the M3104
Industrial Touch Screen Monitor
. This manual contains
inf
ormation and instructions for the monitor. Please refer to it if you have questions about
the monitor.
Connecting to the M3104 Monitor
There are three input/output connections to the M3104 monitor: power, serial and video.
See
figure below.
Power
Yo
ur M3104 monitor is powered by connecting a 2.5mm circular jack to a 12Vdc @ 1.5A power
supply or greater must be used.
Video
The video (DB15HD) connection is made by connecting a video cable between the monitor and
the video source connector on the PC.
Serial
The serial (DB9) connector is provided for touch screen communication. A serial cable from this
connector to the appropriate COM port on the PC that has been setup in the touch driver
installation is necessary for the touch function to operate.
M3104 Industrial Touch Screen Monitor
2
General Specifications and System Requirements
Physical
Enclosure:
Black powder coated aluminum front bezel
Yellow chromate aluminum rear cover
Sealing:
NEMA 4/12 properly mounted w/ sealing gasket
Weight:
3.5
lb.
Connec
tors:
DB
-
15HD Female (video interface)
DB
-
9, Female (serial interface)
RAPC 712, Male 2.5mm (12VDC power)
Viewing Area:
8.31 x 6.23 inches
Display Size:
10.4 inch (diagonal)
Electrical
Voltage:
12VDC ±10%, 100mV Ripple
Current Range:
1A nominal
Functional
Display Type:
Active Matrix TFT Color LCD
Colors:
262,144
Display Modes:
VGA, EGA, CGA with automatic mode detect
Resolution:
640x480 Pixels in VGA mode, will also support CGA and EGA
modes
Frequency:
31.5 kHz Horizontal Typ., 60 to 75 Hz V
ertical Rate
Interface:
Standard analog VGA
Signals:
R G B, HSYNC and VSYNC
OSD:
MENU, SEL, UP, DOWN
Environmental
Temperature:
Operating 0
C to +50
C; Non
-
Operating
-
25
C to +60
C
Shock:
30G, half sine, 11ms, 3 times per axis, non
-
operating
Vibrat
ion:
10Hz to 500Hz @ 1.5G
Humidity:
95% Non
-
condensing
The M3104 monitor supports CGA, EGA and VGA compliant video input which complies with the input
specification. The vertical refresh rate has a maximum supported frequency of 75 Hz. Many VGA sources
can
operate at much higher refresh rates and, for CRT monitors, the higher the refresh the more flicker
-
free the
display. On the M3104 monitor, the refresh rate doesn't determine display quality. Most video sources offer
multiple refresh rates. The typic
al VGA (640x480) refresh rate is 60 Hz.
M3104 Industrial Touch Screen Monitor
3
Adjustments & Calibration
Due to variations in operating environments, user preferences, and hardware, the M3104 is provided with control
buttons that allow the user to adjust the settings of the monitor.
Using The C
ontrol Buttons
The monitor has four control buttons and a power on/off button on the rear of the monitor which allow the user to
make adjustments. See figure below.
The On Screen Display (OSD) will open when the MENU button is pressed. Use the SEL and UP
-
DOWN buttons
to select and set the desired calibration mode. Press the MENU button to step back in the menu. The monitor will
return to normal operation (exit OSD) if no buttons are pressed after a period of time.
Quick Set Buttons
Auto adjustment (Pre
ss SEL)
The monitor will run a short routine to set various calibration modes automatically when the SEL button is pressed
in normal operation (no OSD screen active)
M3104 Industrial Touch Screen Monitor
4
Maintenance and Care
The M3104 has been designed for demanding applications and theref
ore requires little
maintenance.
Reasonable care should be taken when connecting or removing the interface cables so that the
connector pins are not damaged. This is same care that is required for any computer or monitor.
Backlight
During the life of t
he monitor, the fluorescent backlight may need to be replaced. The normal life
of the tubes is 25,000 hours minimum.
Cleaning
For best results, use a clean non
-
abrasive cloth towel dampened with mild soapy water to clean
all external surfaces of the mon
itor.
For the viewing area, use a clean non
-
abrasive cloth towel dampened with commercially available
window cleaners or mild soapy water.
M3104 Industrial Touch Screen Monitor
5
Energy Saving Mode
Energy Saving Mode
When the M3104 monitor is connected to an energy saving compatible computer,
the monitor will
comply with the control signals to power down the monitor into a lower power state.
Caution: The power saving function will automatically put the monitor into active
-
off state if you
turn on the monitor and leave the rest of the system
off. However, once the monitor can sense
the horizontal and vertical sync’s, it will automatically return to its normal operation state.
M3104 Industrial Touch Screen Monitor
6
Touch Screen
The
M3104
Industrial Touch Screen Monitor
is provided with an integrated touch screen overlay.
The tou
ch screen is activated by connecting the seria
l port of the M3104
monitor with the serial
port of the PC. You must also install the drivers for the operating system you are using. These
drivers are available as download zip files from the support page of
the StarPanel web site.
http://www.starpanel.com/support/FTPLinkPage.html#Downloads
After installing the appropriate driver you will need to set it for the monitor touch parameters listed
below.
Touch Driver Installation Options
Note:
When installing
touch drivers the configuration for the monitor is
TSHARC
-
12
and
the baud rate is
9600
.
Inhaltsverzeichnis
