StarTech.com SATSASBP425 Bedienungsanleitung
Manual Revision: 01/09/2015
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SATSASBP425
4-Bay 2.5in SATA/SAS Hard Drive Backplane
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View...................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Hard Drive Installation ..........................................................................4
Hard Drive Removal ................................................................................................................................. 6
How to Use ..............................................................................................7
Connecting the Hard Drive.................................................................................................................... 7
Disconnecting the Hard Drive.............................................................................................................. 7
Initializing the Hard Drive ...................................................................................................................... 7
Technical Support ..................................................................................9
Warranty Information............................................................................9
Instruction Manual
1
Product Diagram
Front View
Rear View
1. 4x 2.5” Drive bays/trays
2. 4x 2.5” Drive bay key hole
3. 4x Drive Tray Release Latches
1. 2x Drive power connector ports (LP4)
2. 4x SATA data connector ports
3. 2x Drive cooling fans
Instruction Manual
2
Introduction
Packaging Contents
• 1x 4-Bay 2.5in SATA/SAS Hard Drive Backplane
• 2x Drive bay keys
• 4x 2.5” HDD/SSD Drive Trays
• 4x SATA cables
• 2x SATA to Molex Power Adapters
• 16x Drive Mounting Screw Kit
• 8x Backplane Mounting Screw Kit
• 1x Instruction Manual
System Requirements
• 1x - Computer System
with:
• 4x SATA/SAS host connector ports
• Available 5.25” bay
• 2x - Available SATA or LP4 Power Connections
• Up to 4x - 2.5in SATA/SAS Hard Drive(s)
Instruction Manual
3
WARNING! Hard drives and storage docks require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data may result.
Always handle your hard drive and storage device with caution. Be sure that you
are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
Installation
Hardware Installation
1. Ensure your computer system is powered down, and the power cable has been
disconnected from the Power Supply.
2. Open your computer case (refer to the computer user manual for details), and place
the 2.5in SATA/SAS HDD Backplane into an available 5.25” slot, lining up the side
installation holes on the Backplane (pictured below), with installation holes on the
5.25” slot inside the computer.
3. Hold the Backplane into place, and x the four included drive bay screws (black)
through the installation holes on the 5.25”bay, into the side installation holes on the
Backplane.
4. Connect the 4x included SATA cables from available SATA/SAS host ports on your
motherboard to the SATA/SAS data connector ports on the back of the Backplane.
5. Connect 2x LP4 Molex or SATA Power (Using the two provided SATA to Molex
adapters) connectors from your power supply to the Molex power connector ports
on the back of the backplane.
Note: For optimal performance, ensure each power connector is on a dierent
power rail. Failure to do so may result in power disruption while swapping drives.
Instruction Manual
4
Hard Drive Installation
1. Insert either of the included bay keys into the your desired 2.5in Drive bay key
holes depending on which tray you intend to install the drive into. And Turn the key
clockwise into the unlock position.
2. To remove the tray, squeeze the latch, pull the tray door handle open and slide the
tray out of the enclosure.
3. Insert your desired drive into the drive tray with the bottom mounting drive holes
in line with the mounting holes on the drive tray. Fix the drive to the drive tray using
four of the included drive screws (silver).
Instruction Manual
5
4. Slide the drive tray with installed hard drive back into the slot and close the door.
5. (Optional) If you would like to lock the drive door for added security, use the key to
turn the key counter clockwise into the locked position.
Instruction Manual
6
Hard Drive Removal
1. Insert either of the included bay keys into the “2.5in Drive bay key holes depending
on which type of drive you intend to remove. And Turn the key clockwise into the
unlock position.
2. Pull the drive door handle to open the drive bay and remove your drive.
Note: It is important to eject or unmount the hard drive from your computer
system before physically removing the drive. See How to Use - Disconnecting the
Hard Drive section for instructions.
Instruction Manual
7
How to Use
Connecting the Hard Drive
Once the drive has been installed in the drive bay, the drivers will install automatically,
and the inserted drive will be accessible as though it were installed within the system.
Note: some operating systems may require that the system be scanned for hardware
changes from within device manager, for the newly connected drive(s) to be
recognized.
Prior to using the drive, it will need to be formatted according to your operating
system requirements.
Refer to Initializing the Hard Drive.
Disconnecting the Hard Drive
Windows
The drive should be uninstalled from device manager, or unmounted using third party
hot swap software.
Note: Removing the connected drive while it is active in the system could result in
losing or corrupting data stored on the drive.
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
icon for the drive on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the enclosure/drive from the computer.
Initializing the Hard Drive
1. If the SATA Hard Drive is blank it may need to be initialized and formatted before
use. From the main Windows desktop, right-click on “My Computer” (“Computer”in
Vista/ 7 / 8), then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
Inhaltsverzeichnis
Andere StarTech.com Computerhardware Handbücher
StarTech.com
StarTech.com EC1U2F Bedienungsanleitung
StarTech.com
StarTech.com SATDOCK4U3RE Bedienungsanleitung
StarTech.com
StarTech.com ECESATA22 Bedienungsanleitung
StarTech.com
StarTech.com PEX40GQSFDPI Bedienungsanleitung
StarTech.com
StarTech.com ATXPOW430HS Handbuch
StarTech.com
StarTech.com ECUSB3S1 Bedienungsanleitung
StarTech.com
StarTech.com PEX13943 Bedienungsanleitung
StarTech.com
StarTech.com FAN939775HP Bedienungsanleitung
StarTech.com
StarTech.com VSEDIDHD Bedienungsanleitung
StarTech.com
StarTech.com CBUSB220 Bedienungsanleitung
StarTech.com
StarTech.com FAN8025PWM Bedienungsanleitung
StarTech.com
StarTech.com S25SLOTR Systemhandbuch
StarTech.com
StarTech.com PEXUSB311EI Bedienungsanleitung
StarTech.com
StarTech.com EC230USB Bedienungsanleitung
StarTech.com
StarTech.com 4P6G-PCIE-SATA-CARD Bedienungsanleitung
StarTech.com
StarTech.com EC2S55254 Bedienungsanleitung
StarTech.com
StarTech.com MPEX1394B3 Bedienungsanleitung
StarTech.com
StarTech.com EC13941A1B Bedienungsanleitung
StarTech.com
StarTech.com PEXSAT32 Bedienungsanleitung
StarTech.com
StarTech.com EC13941A1B Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
