Steamist TSC-250T Bedienungsanleitung
4
1
21
TIME
TEMP
IM
STOP
3
2
6
5
7
1½“ Hole
located four feet
from the floor Double-Sided
Adhesive Pad
IMPORTANT: Run the
Control Cable through
a ¾” conduit.
Coupler
To Steam Generator
Inside Installation:
TSC-250 Control. Locate
away from the direct line
of shower spray and do
NOT locate above
steamhead.
CUS
®
Installation & Operating Instructions
06/11 Pub. No. 271-B
- 1 -
Steambath Control Models: TSC-250 & TSC-250T
Control Features
1.Display: The digital read out displays the ambient temperature, set point
and remaining time in minutes. It is also used to display diagnostic error
codes.
2. Steam Icon: When illuminated the steam cycle is running.
3.Water Icon: When steam shower is not in use the blue water waves
indicate the InstaMist feature is on. This is also illuminated when the
steam bath cycle is running.
4. Time / Temp button: Used to program the default timer when the steam
bath is off. Adjustments are made with the Up/Down buttons. The button
will switch between time and temperature when the steam bath is on.
Adjustments to the timer made during a steam bath cycle are temporary.
All temperature adjustments are held in memory for the user of the cycle
that is running.
5.IM/Stop button: Toggles the InstaMist feature on/off when the steam
bath is off and stops the steam bath cycle when a cycle is started.
InstaMist is a preheat function that keeps the water heated for quick
starts.
6.User 1 button: Starts the user one cycle and is the up function while in
cycle.
7.User 2 button: Starts the user two cycle and is the down function while
in cycle.
IMPORTANT: This control must be installed inside the steam room
for proper operation of the system.
Cleaning Instructions: Use a damp cloth and mild soap.
Do NOT use abrasive cleaners which might scratch the
surface or the base of the control.
IMPORTANT: The TSC-250 Control will only function with
the current TSG steam generators.
TSC-250 Digital Temperature Control
Installation Instructions
1.Pre-Installation - Control Location
a) The TSC-250 Control must be installed inside the steam room. For
convenience the recommended height from the floor is four feet. Provide
a 1½" hole in the wall at this location (see Figure 1).
IMPORTANT: Multi-conductor cable must be installed so that the end will
not be buried inside the wall. The unit will not operate unless the control
is installed.
2. Electrical Rough-in
a) Remove the multi-conductor cable from the control packing box. Carefully
route the multi-conductor control cable from the steam generator to the
TSC-250 located inside the steamroom (see Figure 1). Route
multi-conductor cable through a ¾" conduit to protect the cable from
damage and to facilitate replacement if necessary.
3.Control and Cable Installation
a) Locate the previously installed cable and black plastic strain relief clamp
which is in the control packing box. Locate the knockout on the steam
generator for the control cable (see Figure 3).
b) Place strain relief around cable about seven inches from the end and
insert into the hole. Remove the protective covering labeled “Remove
Before Installation” from the modular jack found on the PC board.
c) Remove the protective cap from the multi-conductor cable plug. Connect
the cable to the modular jack.
d) Close and secure generator cover.
e) Locate Telco Jack at female coupler, on back of the TSC-250 control.
Remove the protective covering labeled “Remove Before Installation”.
Remove protective cap from cable and plug into jack. Check that the
orientation of the plug properly aligns with the jack. A snap will
indicate the plug is installed correctly (see Figure 3).
WARNING: Test the control for operation before continuing on
to the next step.
f) Peel adhesive liner from back of the control. Apply the control
to the wall. Press firmly and hold for a few seconds.
g) After the control is in place, apply silicone (supplied) around
the control to form a watertight seal (see Figure 2).
Figure 1
WARNING: Elderly persons, pregnant women, or those suffering from heart disease, high blood pressure, diabetes, or
who are otherwise not in good health, do not use this device unless directed to do so by a physician. Also, do not use
steambath while under the influence of alcohol. For additional Important Safety Information, please see a separate
instruction sheet Pub. No. 199.
!
®
Coupler
Control Cable
to Generator
Adhesive Liner Modular Jacks:
All four modular jacks are
identical and work in
any combination.
Connect to any jack.
¾" Conduit
To Control
ENOCILIS
RA
E
LC
.Z
O.
LF
2
/
1
t
eN 02513.oNmetI
.
A
.S
.U
NI
E
D
A
M
STOP
2
12
1
TIME
TEMP
IM
STOP
Steamhead Installation
Steamhead should be mounted
18" above the finished floor or
6" above the rim of the tub as
far from the bather as possible
TSX-220
Auxilary Outside
Control
TSC-250 or TSC, TSC-350
inside control required. Locate
away from the direct line of
shower spray and do NOT
locate above steamhead.
All Instructions must be given to the homeowner for future use.
06/11 Pub. No. 271-B
- 2 -
IMPORTANT: The adhesive on the back of the TSC-250 control will NOT
seal this control. It is the responsibility of the installer to seal this control to
the wall with the supplied silicone. Water damage to the control is not
covered by the warranty.
Figure 4 - Installation Suggestions
Operating Instructions
Additional Features
Operation: Make sure the water and power are turned on. Simply
press USER 1 or USER 2 keypad to begin the cycle. Pressing the
Stop keypad will cancel the cycle. After a cycle is started it will take a
few minutes for the Steam Generator to heat up and begin producing
steam. This time will be less if the InstaMist has been ON. During
operation the display will show the ambient temperature or the
remaining time. This can be selected by toggling the TIME/TEMP
keypad.
Programming: : Adjustments can be made to the temperature only
while a cycle is started. When the temperature is displayed, the set
temperature can be viewed or changed by momentarily pressing the
up or down keypad. Temperature adjustments made when USER 1
cycle is started will be saved to USER 1 and likewise for USER 2. All
changes made to the temperature control are stored in memory until
changed again. The temperature range is 60°F to 125°F (16°C to
52°C). While a cycle is running the remaining time can be adjusted up
or down. This adjustment is only for the current steam bath cycle. The
default time is programmed when the cycle is off by momentarily
pressing the TIME/TEMP keypad. Any adjustments made at this time
are stored as the new default time for both users.
The InstaMist feature can be selected or deselected while the system
is in the off mode. Simply press the IM keypad and the blue waves will
light to indicate you are in InstaMist mode. InstaMist keeps the
generator warm for a faster heat up.
Memory: The temperature set points for USER 1, USER 2, the default
time, and the selection of InstaMist are retained even if there is a
power failure.
Service Modes: To enter the service mode, in the Off mode press and
hold the TIME/TEMP button. After 3 seconds you are in service mode
and can do one of the following three functions. The service mode will
be indicated by the display of either an F or C (Fahrenheit/Celsius)
indicating the current setting. You must continue to hold the
TIME/TEMP keypad to stay in the service mode.
Service mode 1: While continuing to press the
TIME/TEMP keypad press the up arrow to change to
Fahrenheit or Celsius. The display will show the
current setting “F” or “C”. Let go to save you setting.
Service mode 2: While continuing to hold the
TIME/TEMP button, press and hold the down arrow
for 5 seconds to reset factory defaults. All the display
characters will light for 2 seconds indicating it was
done successfully.
Service Mode 3: While continuing to hold the
TIME/TEMP button press the IM/STOP button and
the program version will be displayed.
Error Messages: This control is programmed with a
diagnostic feature to help isolate any potential
problems. Errors are displayed by flashing an “Er”
followed by a 2 digit number. The first digit is the
device number. Zero for the control and 1-4 for the
generators. The second digit is the error code for that
device. Error messages “Er 01”, “Er 02”, and “Er 04”
indicate a problem internal to the control. If this
occurs, the control should be replaced. Error
messages “Er 03” means the control could not communicate with a
steam generator and may be a cable connection problem. If this error
occurs, check both ends of the control cable for clean, dry and secure
connections. Dirty contacts can be cleaned with alcohol and a cotton
swab or a toothbrush. This can also happen if the control is not sealed
and the cable connections get wet. Also make sure the generator is
not in test mode. Try resetting the breaker. Generator error codes are
not covered in this document.
Figure 2
Figure 3 - Cable Installation on Steam Generator
Installation & Operating Instructions
East Coast Office: 25 E. Union Ave., East Rutherford, NJ 07073 • Tel: 800-577-6478 • Fax: 201-933-0746
West Coast Office: Tel: 800-355-6478 • Fax: 661-940-1617
®
Andere Steamist Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
