STEELTEC 52CC Bedienungsanleitung
2
STEELTEC MULTITOOL
CONTENTS OF BOOKLET
Warnings Check List Page 3
What Is In Your Box/Assembly Page 4
Blade Assembly/Air Filter AƩachment Page 5
Blade Assembly/Air Filter AƩachment Page 6
Pole Assembly And AƩaching Page 7
OperaƟng The Pruner/Installing The Bar And Chain Page 8
AdjusƟng The Chain Page 9
Chain Oiler/Filling The Oil Resvoir/AdjusƟng The Oil Flow Rate Page 10
Typical ApplicaƟons Standard Cut Page 11
Steps For StarƟng Your Machine Page 12
How To Mix The Fuel Page 13
AdjusƟng The Idle Screw On Your Machine/Fuel Mixture Screw Adjustment Page 14
Maintenance On Your Pole Pruner Page 15
AƩaching Blades/AƩaching Nylon CuƩer And Bracket Onto Guard Page 16
How To Open And Close Whipper Snipper Head Page 17
Cuƫng OperaƟon/Maintenance Of Your Machine Page 18
Hedge Trimmer AƩachments Page 19
Installing The Hedge Trimmer Cuƫng Assembly/AdjusƟng The
ArƟculated Hedgetrimmer Cuƫng Assembly Page 20
AdjusƟng The Hedgetrimmer Cuter Assembly For Desired Cuƫng Angles/AdjusƟng
The CuƩer Assembly For Storage Or TransportaƟon/How To Use Hedgetrimmer AƩachment Page 21
Daily Maintenance Page 22
3
BEFORE USING THIS UNIT:
Please Read the Operator’s manual carefully.
Check that the Cung equipment is correctly assembled (please
read and follow instrucons on Page 5)
Start the Unit and check the carbureor adjustment (Please check
Page 11 for this step if needed)
Always Wear Eye, Head and Ear Protectors when
Using This Unit.
Keep all Children, bystanders and helpers 15m (50) away from
Unit. If anyone approaches you, stop the engine and cung
aachment immediately.
Gloves, Safety Goggles and ear muffs and Slip and Sturdy Footwear
should be worn at all mes when operang
tools or Machinery.
ALWAYS MAINTAIN THIS MULTITOOL ACCORDING TO THE OWNER’S
MANUAL AND FOLLOW THE RECOMMENDED SCHEDULED
MAINTENANCE.
NEVER MODIFY OR DISABLE ANY OF THE POLE PRUNER’S
SAFETY DEVICES.
ALWAYS USE GENUINE PARTS AND ACCESSORIES WHEN REPAIRING
OR MAINTAINING THIS MACHINE. DO NOT MAKE UNAUTHORIZED
MODIFICATIONS OR SUBSTITUTIONS TO THE GUIDE BAR OR CHAIN
NEVER ALLOW THE ENGINE TO RUN AT HIGH RPM WITHOUT A
LOAD. DOING SO COULD DAMAGE
THE ENGINE.
WHEN TRANSPORTING THE PRUNER IN A VEHICLE, TIE IT DOWN
SECURELY TO PREVENT DAMAGE AND FUEL SPILLAGE.
ALWAYS CLEAR YOUR WORK AREA OF TRASH OR HIDDEN DEBRIS
TO HELP ENSURE GOOD FOOTING.
KEEP THE SAW CHAIN SHARP AND PROPERLY ADJUSTED
KEEP THE PRUNER AS CLEAN AS POSSIBLE. KEEP IT FREE OF LOOSE
VEGETATION, MUD ETC.
15m (50ft)
4
ACCESSORIES:
G1. 12” Chain cover
G2. 12” Guide Bar
G3. 12” Chain
J2. Poles
2,3 or 4 Poles vary depending
on product.
M. Hedge Trimmer
H. Coupler
K. Chain Head
N. Brush Cuer
i1. Airfilter
D. Hex screw for Air filter on the motor
L. Shoulder Strap
O. D Handle
G3
G1
G2
H
J2
J2
M
K
N
O
P
L
H
i
D
G2
G
G
G
G
G
G
G
G
G
J2
J2
J
2
J
J
M
M
M
M
M
M
M
M
H
H
K
K
K
K
K
K
K
K
N
N
N
N
N
N
N
N
N
i
i
i
L
STANDARD COMPONENTS
A. 4x Hex Screws & Nuts (Handle)
B. Nylon Cuer
C. Nylon Cuer Scew
D. 2 plasc es
E. Hex for Air filter on the motor
F. Tools
WHAT IS IN YOUR BOX
B
C
E
D D
F2 F2
F2
A
A
F
F
F
5
HANDLE ASSEMBLY:
STEP 1
Rubber sleeve should already be on pole.
STEP 4
Place the top segment of the handle as seen above.
STEP 2
Insert nuts into the boom segments of the handle as
seen above.
STEP 3
Place the boom segment of the handle into the groove
of the rubber sleeve.
STEP 5
Insert hex screws provided.
6
D
i
ATTACHING THE AIR FILTER TO YOUR MACHINE:
BLADE ASSEMBLY
EIGHT TOOTH
FOURTY TOOTH
THREE TOOTH
FOUR TOOTH
(please note that quanes of blades will vary per model - 5in1, 6in1, 7in1, 8in1)
TWO TOOTH
PLASTEC
7
POLE ASSEMBLY & ATTACHING
1ΉAach Coupler/Joiner (H) to the end of the pole that does
not have the pre-drilled inxdex hole. Phsical holes are
not neccessary for aaching the joiner. Screws on
coupler or joiner are pressure aached against pole.
3ΉPlace pole into joiner with index hole facing upwards.
Adjust/Rotate the hole unl it firmly clicks into place.
2ΉVisible holes at the base of the pole are
4ΉPush down the safety shield firmly unl it locks into
place. Once down ghten the T-handle unl its firm (to
protect the release mechanism).
5ΉRELEASE
Release the safety sheild and push down on the release
clip while gently rotang and removing pole.
H
H
BASE OF POLE
Index hole facing up
TOP OF POLE
Coupler Attaches this end
SCREWS
Screw in Hex screws until
firm against pole.
H
H
H
H
H
H
H
H
H
H
8
Hook the strap hook to the outer pipe on the sha
of the machine
Wear the strap so that the hook stays at your right hand side.
Adjust the length of the strap so that it is comfortable and at the
correct length whilst operang the pruner.
In emergency situaons unhook the metal clasp, this will release
the machine from the strap.
Please View Mega Machine Warehouse Help Videos For Installation.
of Poles and Starting Sequence For Operation Of This Machine.
OPERATING THE PRUNER
INSTALLING THE BAR AND CHAIN
NEVER ATTEMPT TO INSTALL, REPLACE, OR ADJUST THE CHAIN WITH THE ENGINE RUNNING!
WARNING! THE SAW IS VERY SHARP. WEAR GLOVES TO PROTECT YOUR HANDS WHEN HANDLING.
1ΉUsing the small end of the plug wrench remove sprocket
cover nut (turn counterclockwise to remove).
3ΉInstall the chain loop over the drive links within the guide bar groove, and then align the chain over the drive sprocket.
Make sure the cuer are properly oriented as shown in the picture below.
2ΉPlace the guide bar over the guide bar adjustment stud
on the cung head assembly. Align the chain tension pin
with the hole in the guide bar.
4ΉInstall the sprocket cover over the bar stud.
Using finger-pressure only, install the
sprocket cover nut.
9
IMPORTANT
Proper chain adjustment is essenal for maximum performance, long chain life, and operator safety. Always inspect chain tension before
operang the pole pruner.
1ΉLoosen the sprocket cover nut with a Plug wrench.
2ΉLithe nose of the guide bar while turning the chain tensioning screw
Clockwise to ghten the chain Counterclockwise to loosen the chain.
3ΉPull the Chain by hand along the top of the guide bar several mes from the engine to the bar’s p. The chain should feel sung
but sll pull freely.
4ΉTighten the sprocket cover nut securely while liing the p of the guide bar.
5ΉInspect the chain for correct adjustment (more frequently with a new chain). The chain should feel snug but sll pull freely.
ADJUSTING THE CHAIN
NEVER ATTEMPT TO INSTALL, REPLACE, OR ADJUST THE CHAIN WITH THE ENGINE RUNNING. WARNING! THE SAW CHAIN IS VERY SHARP.
WEAR GLOVES TO PROTECT YOUR HANDS WHEN HANDLING.
CAUTION! A LOOSE CHAIN CAN JUMP OFF THE GUIDE BAR CAUSING DAMAGE TO THE CHAIN AND ASSOCIATED EQUIPMENT. ALWAYS MAKE
SURE THE CHAINS IS PROPERLY ADJUSTED; CHECK MORE OFTEN WHEN YOU ARE BREAKING IN A NEW CHAIN.
10
CHAIN OILER
FILLING THE OIL RESEVOIR
The oil reservoir has a capacity sufficient to provide about 40 minutes of cung me (when set to deliver the minimum flow rate)
1ΉPlace the pole pruner on a clean, flat surface with the oil filler cap facing up.
Wipe offany debris from the oil cap and from around the oil filler neck.
2ΉRemove the oil filler cap and fill the reservoir with bar and chain oil, then replace the cap.
3ΉWipe up spilled oil from the unit before restarng the pole pruner.
ADJUSTING OIL FLOW RATE
The guide bar and chain are lubricated automacally by a pump that operates whenever the chain rotates, the pump is set at the factory to
deliver a medium flow rate, but it can be adjusted in the field. A temporary increase in oil flow is oen desireable when cung things like
hardwood or wood with a lot of pitch.
ADJUST THE PUMP AS FOLLOWS:
1ΉStop the engine and make sure the stop switch is in the
STOP posion.
2ΉPlace the unit on it’s side with the oil Reservoir up
3ΉWith a screw driver, push in on the oil flow rate adjusng
screw and turn in the desired direcon (there are
three incremental sengs):
CLOCKWISEͳDECREASE LUBRICATION
COUNTERCLOCKWISEͳINCREASE LUBRICATION
NEVER FILL THE OIL RESERVOIR NOR ADJUST THE OILER WITH THE ENGINE RUNNING.
N
Andere Handbücher für 52CC
1
Inhaltsverzeichnis
Andere STEELTEC Elektrowerkzeuge Handbücher
