Steinberg UR24C Benutzerhandbuch

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly

approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/ or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result

in harmful interference with other electronic

devices. This equipment generates/uses radio

frequencies and, if not installed and used according

to the instructions found in the users manual, may

cause interference harmful to the operation of other

electronic devices. Compliance with FCC

regulations does not guarantee that interference

will not occur in all installations. If this product is

found to be the source of interference, which can

be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to co-axial

type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you

can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic

Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : USB AUDIO INTERFACE

Model Name : UR24C

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired

operation.

* This applies only to products distributed by Yamaha Corporation of America. (FCC SDoC)

UR24C Startup Guide 3

Contents

Message from the development team................................... 4

Package Contents................................................................... 4

PRECAUTIONS........................................................................ 5

Notice..................................................................................................... 6

Information ............................................................................................. 7

Manuals.................................................................................... 8

Conventions in this manual ................................................... 8

TOOLS for UR-C...................................................................... 9

Yamaha Steinberg USB Driver .............................................................. 9

Steinberg UR-C Applications ................................................................. 9

Basic FX Suite ....................................................................................... 9

Preparation before using with a computer.......................... 10

Installing TOOLS for UR-C ................................................................... 10

Activating Basic FX Suite...................................................................... 12

Downloading Cubase AI ....................................................................... 12

Preparation before using with an iOS/iPadOS device........ 13

Apple accessories................................................................................. 13

Downloading Steinberg dspMixFx UR-C (mixing app).......................... 13

Downloading DAW app as necessary .................................................. 13

Setting up the power supply................................................. 14

Connecting the USB cable (bus-powered) ........................................... 14

Connecting the USB power adaptor or the USB mobile battery ........... 14

English

Message from the development team

4UR24C Startup Guide

Message from the development team

Thank you for choosing the UR24C USB Audio Interface.

As a new lineup of the UR Series, three UR-C Series models were released in 2019. Now, we

are adding the new UR24C model.

Although the UR24C is a simple 2-in/4-out design, it features two powerful monitoring functions

(Monitor Mode DAW and Monitor Mode DJ) that allow you to cover a variety of completely

different usage scenarios with a single interface.

Monitor Mode “DAW” is convenient for producing music with a DAW such as Cubase.

For example, you can use direct monitoring and the built-in effects for latency-free recording.

It also has a loopback function that you can use when streaming your music live over the

Internet.

Monitor Mode “DJ” allows you to monitor two separate output signals at the same time on a

single pair of headphones. This mode is particularly useful if you use DJ software.

The UR-C series is gradually evolving along with the changing needs in audio production.

We will continue to make every effort to fully support the creative efforts of our users.

The Steinberg Hardware Development Team

Package Contents

The package of this product contains the following items. After opening the package, make

sure that it includes everything listed below.

1UR24C main unit 2USB 3.0 cable (3.1 Gen1, Type-C to Type-A, 1.0 m)

3UR24C Startup Guide (this book) 4CUBASE AI DOWNLOAD

INFORMATION

5ESSENTIAL PRODUCT LICENCE

INFORMATION

PRECAUTIONS

UR24C Startup Guide 5

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place

for future reference.

This product is designed for music

production/recording. Do not use for any

purposes other than the one intended.

Those who are unfamiliar with handling or

those who can not handle according to this

manual such as children, should be

supervised by responsible persons to

ensure safety.

WARNING

Always follow the basic precautions

listed below to avoid the possibility of

serious injury or even death from

electrical shock, short-circuiting,

damages, fire or other hazards. These

precautions include, but are not limited

to, the following:

If you notice any abnormality

• If any of the following problems occur,

immediately unplug the USB cable from the

computer.

- The USB cable becomes frayed or

damaged.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped

into the product.

- There is a sudden loss of sound during use

of the product.

- Cracks or other visible damage appear on

the product.

Then have the product inspected or repaired

by qualified Yamaha service personnel.

Do not open

• This product contains no user-serviceable

parts. Do not attempt to disassemble the

internal parts or modify them in any way.

Water warning/Fire warning

• Do not expose the product to rain, use it

near water or in damp or wet conditions, or

place on it any containers (such as vases,

bottles or glasses) containing liquids which

might spill into any openings.

• Do not place any burning items or open

flames near the product, since they may

cause a fire.

Hearing loss

• Before turning the power of all devices on or

off, make sure that all volume levels are set

to the minimum. Failing to do so may result in

hearing loss, electric shock, or device

damage.

• When turning on the AC power in your audio

system, always turn on the power amplifier

LAST, to avoid hearing loss and speaker

damage. When turning the power off, the

power amplifier should be turned off FIRST

for the same reason.

• Do not use headphones for a long period of

time at a high or uncomfortable volume level,

since this can cause permanent hearing

loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

CAUTION

Always follow the basic precautions

listed below to avoid the possibility of

physical injury to you or others. These

precautions include, but are not limited

to, the following:

Location and connection

• Do not place the product in an unstable

position or a location with excessive

vibration, where it might accidentally fall over

and cause injury.

• Keep this product out of reach of children.

This product is not suitable for use in

locations where children are likely to be

present.

PA_en_11 1/2

PRECAUTIONS

6UR24C Startup Guide

• Do not place the product in a location where

it may come into contact with corrosive

gases or salt air. Doing so may result in

malfunction.

• Before moving the product, remove all

connected cables.

Maintenance

• Remove the USB cable from the computer

when cleaning the product.

Handling caution

• Do not rest your weight on the product or

place heavy objects on it.

Notice

To avoid the possibility of malfunction/

damage to the product, damage to data, or

damage to other property, follow the notices

below.

Handling and maintenance

• Do not use the product in the vicinity of a TV,

radio, or other electric products. Otherwise,

the product, TV, or radio may generate noise.

• Do not expose the product to excessive dust

or vibration, or extreme cold or heat, in order

to prevent the possibility of panel

disfiguration, unstable operation, or damage

to the internal components.

• Do not install in locations where temperature

changes are severe. Otherwise,

condensation may form on the inside or the

surface of the product, causing it to break.

• If there is reason to believe that

condensation might have occurred, leave

the product for several hours without turning

on the power until the condensation has

completely dried out, in order to prevent

possible damage.

• Do not place vinyl, plastic or rubber objects

on the product, since this might cause

alteration or discoloration of the panel.

• When cleaning the product, use a dry and

soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-

impregnated wiping cloths, since this might

cause alteration or discoloration.

PA_en_11 2/2

PRECAUTIONS

UR24C Startup Guide 7

Information

About copyrights

• The software included in the TOOLS for

UR-C and the copyrights thereof are under

exclusive ownership by Yamaha

Corporation.

• This manual is the exclusive copyrights of

Yamaha Corporation.

• Copying of the software or reproduction of

this manual in whole or in part by any means

is expressly forbidden without the written

consent of the manufacturer.

• This product incorporates and bundles

computer programs and contents in which

Steinberg Media Technologies GmbH and

Yamaha Corporation own copyrights or with

respect to which it has license to use others’

copyrights. Such copyrighted materials

include, without limitation, all computer

software, style files, MIDI files, WAVE data,

musical scores and sound recordings. Any

unauthorized use of such programs and

contents outside of personal use is not

permitted under relevant laws. Any violation

of copyright has legal consequences.

DON’T MAKE, DISTRIBUTE OR USE

ILLEGAL COPIES.

About functions/data bundled

with the product

• XLR-type connectors are wired as follows

(IEC60268 standard): pin 1: ground, pin 2:

hot (+), and pin 3: cold (-).

About this manual

• The illustrations and screens as shown in

this manual are for instructional purposes

only.

• Steinberg Media Technologies GmbH and

Yamaha Corporation make no

representations or warranties with regard to

the use of the software and documentation

and cannot be held responsible for the

results of the use of this manual and the

software.

• Steinberg, Cubase and Cubasis are

registered trademarks of Steinberg Media

Technologies GmbH.

• Windows is a registered trademark of

Microsoft®Corporation in the United States

and other countries.

• Apple, Mac, iPad, iPadOS, iPhone, and

Lightning are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• IOS is a trademark or registered trademark

of Cisco in the U.S. and other countries and

is used under license.

• The company names and product names in

this manual are the trademarks or registered

trademarks of their respective companies.

• Software may be revised and updated

without prior notice.

About disposal

• This product contains recyclable

components. When disposing of this

product, please contact the appropriate

local authorities.

(bottom_en_01)

Yamaha/Steinberg cannot be held

responsible for damage caused by

improper use or modifications to the

product, or data that is lost or destroyed.

The model number, serial number, power

requirements, etc., may be found on or

near the name plate, which is at the

bottom of the unit. You should note this

serial number in the space provided

below and retain this manual as a

permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

Manuals

8UR24C Startup Guide

Manuals

The UR24C has the following two separate

manuals.

Startup Guide (this book)

Read this manual when setting up the

device. After finishing the setup as

indicated in this manual, read the Operation

Manual.

Operation Manual (PDF)

Read through this manual to understand

how to use the features of the product. You

can download the Operation Manual from

the Steinberg website:

http://www.steinberg.net/hardwaredownloads

NOTE

To view PDF files, you need to install Adobe

Reader on your computer. You can download

the latest version at the following website.

https://www.adobe.com/

Conventions in this

manual

Windows or Mac

When the procedures or explanations are

specific to only one of the platforms,

Windows or Mac, this is properly indicated

in the manual. When the platforms do not

appear, procedures or explanations are for

both Windows and Mac. This manual

predominantly uses screenshots of

Windows. However, Mac screenshots are

used when instructions of the function apply

only to the Mac.

Cubase series

The phrase “Cubase” in this manual applies

to all Cubase programs and versions

(except Cubase LE). If a specific version is

indicated, the version is described in the

text. This manual uses screenshots of

Cubase Pro 10 series. If you are using

another version of Cubase, the actual

screenshots might not be the same. For

details, refer to the Cubase manuals.

Cubasis series

This manual uses screenshots of Cubasis 2.

If you are using another version of Cubasis,

the actual screen shots might not be the

same.

Procedures

An arrow “” is shown for some

procedures in the manual. For example, the

string [Studio] [Studio Setup] [Control

Panel] indicates that you should perform the

procedures in the following order.

1. Click the [Studio] menu.

2. Select the [Studio Setup] option.

3. Click the [Control Panel] button.

Version information

The letters “x.x.x” and “x.xx” indicate the

version number.

TOOLS for UR-C

UR24C Startup Guide 9

TOOLS for UR-C

The software TOOLS for UR-C is necessary

for proper connection and use of the device

with a computer. Make sure to install it

before initially using the device (page 10).

You will need to download TOOLS for UR-C

beforehand from the Steinberg website

below.

http://www.steinberg.net/hardwaredownloads

When you install the TOOLS for UR-C, the

following three software programs will be

installed.

NOTE

• TOOLS for UR-C does not support an iOS/

iPadOS device.

• For the latest information on TOOLS for

UR-C, see the Steinberg website.

Yamaha Steinberg USB

Driver

This software allows communication

between the device and a computer.

Steinberg UR-C

Applications

This software allows setting the parameters

of the device from a computer or using the

Link function between the device and

Cubase series software. The software

consists of the following two components.

• Steinberg dspMixFx UR-C

This editing software lets you set the device

when using the device independently, or

when using it with a DAW (Digital Audio

Workstation) software other than Cubase

series. You can use Cubase and dspMixFx

UR-C at the same time.

• Steinberg UR-C Extension

This software allows you to link the device

with Cubase series (for versions which

supports the link function). To use this link

function, see the Steinberg web site below.

https://www.steinberg.net/

Basic FX Suite

Basic FX Suite is software consisting of

Plug-ins of various effects and sound

processing developed by Yamaha, some of

which fully utilize modeling technology.

When you install the Basic FX Suite, the

following three software programs will be

installed.

NOTE

AU (Audio Unit) Plug-ins are additionally

available, as well as VST Plug-ins, for use with

a Mac.

• Sweet Spot Morphing Channel

Strip

This processing effect is a multi effect that

features a compressor and equalizer.

•REV-X

This processing effect is a digital reverb

platform developed by Yamaha for

professional audio devices.

• Guitar Amp Classics

This processing effect features guitar amp

simulations developed by Yamaha that fully

utilize modeling technology.

Preparation before using with a computer

10 UR24C Startup Guide

Preparation before

using with a computer

The following three setup procedures are

required before you can use the device with

a computer.

• Installing TOOLS for UR-C

• Activating Basic FX Suite

• Downloading Cubase AI (DAW)

Installing TOOLS for UR-C

Download TOOLS for UR-C previously from

the Steinberg website. Follow the steps

below to install the TOOLS for UR-C.

NOTE

• You are only permitted to use this software

pursuant to the terms and conditions of the

“License Agreement” shown during the

installation.

• Future upgrades of application and system

software and any changes in specifications

and functions will be announced at the

following website.

https://www.steinberg.net/

• The eLicenser Control Center (eLCC) for

controlling the product license is installed at

the same time.

Windows

1. Disconnect all USB devices other

than the mouse and keyboard

from the computer.

2. Start the computer and log on to

the Administrator account.

Exit any open applications and close

all open windows.

3. Extract the previously downloaded

TOOLS for UR-C.

4. Double click the [setup.exe] file in

the extracted folder to start the

installation.

5. Follow the on-screen instructions

to install the software.

NOTE

• While installing the software, the “eLicenser

Control Center” installation message

appears. Follow the onscreen instructions to

install the software.

• You can select the desired software to be

installed on the installation screen.

- Yamaha Steinberg USB Driver

- Steinberg UR-C Applications

- Basic FX Suite (VST3 Plug-ins)

6. When installation has been

completed, click [Finish].

If a window requiring you to restart your

computer appears, follow the onscreen

instructions and restart the computer.

Confirmation of Installation

7. Move the [POWER SOURCE]

switch to the left and then connect

the device to a USB 3.0 jack on the

computer with the included USB

cable.

Make sure not to connect it to a USB

hub.

8. Open the [Device Manager]

window as follows.

[Control Panel] ([Hardware and

Sound]) [Device Manager]

Inhaltsverzeichnis

Andere Steinberg Aufnahmegeräte Handbücher

Steinberg

Steinberg NUENDO 2 Bedienungsanleitung

Steinberg

Steinberg UR12 Bedienungsanleitung

Steinberg

Steinberg UR22C Bedienungsanleitung

Steinberg

Steinberg UR 824 Bedienungsanleitung

Steinberg

Steinberg MR816CSX Bedienungsanleitung

Steinberg

Steinberg PSP PianoVerb Bedienungsanleitung

Steinberg

Steinberg AXR4T Bedienungsanleitung

Steinberg

Steinberg R 824 Bedienungsanleitung

Steinberg

Steinberg Nuendo SyncStation Bedienungsanleitung

Steinberg

Steinberg CUBASE PRO 10.5 Bedienungsanleitung

Steinberg

Steinberg UR816C Benutzerhandbuch

Steinberg

Steinberg CI2 Gebrauchsanweisung

Steinberg

Steinberg MR816X Bedienungsanleitung

Steinberg

Steinberg UR 824 Service-Handbuch

Steinberg

Steinberg UR-C V2.0 Anleitungen und Rezepte

Steinberg

Steinberg UR 824 Bedienungsanleitung

Steinberg

Steinberg UR 824 Bedienungsanleitung

Steinberg

Steinberg PRO 24 III Bedienungsanleitung

Steinberg

Steinberg Nuendo 3 Kurzanleitung

Steinberg

Steinberg CI2 Bedienungsanleitung

Steinberg

Steinberg UR44C Benutzerhandbuch

Steinberg

Steinberg AXR4U Bedienungsanleitung

Steinberg

Steinberg AXR4T Bedienungsanleitung

Steinberg

Steinberg UR 824 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch