STEINEL US Quattro COM1-24 Bedienungsanleitung

US Quattro COM1-24

US Quattro COM2-24

US Quattro DIM-24

DT Quattro COM1-24

DT Quattro COM2-24

DT Quattro DIM-24

US Quattro US Oneway

DT Quattro US Hallway

US Oneway COM1-24

US Oneway COM2-24

US Oneway DIM-24

US Hallway COM1-24

US Hallway COM2-24

US Hallway DIM-24

Information

FR EN

- 2 -

Assembly / Installation / Dimensional Drawings

aLoad module

Sensor module

Mounts to a 4" Square box, 4" Octagon box or Round 3.0 Mud-Ring

120

US Quattro /

DT Quattro

US Oneway /

US Hallway

120

Mounts directly to

ceiling with quick

mount spring tabs

120

120 61

120

Ø min. 68 mm (2 11/16 in)

max. 76 mm (3 in)

120

- 3 -

US Quattro COM2-24 / DT Quattro COM2-24 / US Oneway COM2-24 / US Hallway COM2-24

Light level setting

See page 18

Occupancy time

delay setting

See page 18

HVAC

stay-'ON' time

See page 19

HVAC

switch-'ON' delay

See page 19

e f g

Reach setting

See page 19, 20

- 4 -

US Quattro DIM-24 / DT Quattro DIM-24 / US Oneway DIM-24 / US Hallway DIM-24

e f m

Light level setting

See page 18

Occupancy time

delay setting

See page 18

Stay 'ON' time DIM

before 'OFF'

See page 19

Reach setting

See page 19, 20

- 5 -

US Quattro COM1-24 / DT Quattro COM1-24 / US Oneway COM1-24 / US Hallway COM1-24

Light level setting

See page 18

Occupancy time

delay setting

See page 18

Reach setting

See page 19, 20

e f i

- 6 -

Disconnect the power supply

before attempting any work

on the sensor!

Before installation, make sure

that power has been switched

off at the breaker and check

that the circuit is dead with

a voltage tester.

Installing the sensor involves

work on the line voltage power

supply. This work must there-

fore be carried out profession-

ally in accordance with the

applicable Nation Electrical

Codes and electrical operating

conditions.

Control output DIM-24

(1-10 V) must only be used

for connecting electronic

ballasts with an electrically

isolated 10V dimming

control input.

System Components

Load module

Sensor module

Sensor control plate

Sensor DIP switch settings

(1) Normal / Test mode

(2) Manual 'ON' / Automatic

'ON' mode

(3) Momentary / Maintained

switch option

(4) 'ON' only / 'ON'&'OFF'

manual switching

(5) Constant light level DIM

control option

(6)(7)(8)

Trigger mode

(DT Quattro only)

Light level setting

Occupancy time

delay setting

Switching output 1

HVAC stay-'ON' time

Switching output 2

HVAC switch-'ON' delay

Switching output 2

Reach setting



10.1

COM1-24 Wiring



10.2

COM2-24 Wiring



10.3

COM2-24 Multiple Sensor

Wiring



10.4

DIM-24 Wiring



10.5

DIM-24 Multiple Sensor

Wiring

Locking mechanism

Assembly / Installation /

Dimensional Drawings

Stay 'ON' time DIM before

'OFF' option

Trigger mode options

Assembly/Installation (see chart on page 2)

For indoor use only.

Sensor and load modules come

preassembled and must be sepa-

rated for access to the commis-

sioning settings on the backside

of sensor module by opening the

locking tabs kon the sides.

Reconnect and seat the sensor

to the load module and secure

the locking tabs

for normal

operation.

Accessories:

- WGC Wire Guard Cage

- RC 3 Service Remote

- RC 4 User Remote

Operating Instructions

Installer:

This product has been manu-

factured and 100% quality tested.

Please read all of the instructions

before installation. This will help

you to be familiarized with all the

features and options available to

you with these devices.

This will also assist you to mini-

mize installation time and provide

maximum energy savings and

trouble-free operation.

Safety Warnings

- 7 -

How it Works / Basic Function

The Control Pro DT Quattro and

Ultrasonic presence detector

product familiy is intended to

control lighting and HVAC in

commercial buildings, schools,

public building, etc.

Lighting is controlled in relation

to both the presence of motion

and ambient light levels. The HVAC

output on the (COM2-24) is

signaled in relation to only the

presence of motion.

Commissioning adjustments

are made by potentiometer or dip

switch settings on the sensor or by

the optional (RC3 service remote)

commissioning tool.

US Quattro COM1-24

DT Quattro COM1-24

US Oneway COM1-24

US Hallway COM1-24

1 switching output (COM1-24 Low

Voltage) operating in relation to

the detection of motion and

ambient light level.

Settings:

- Light level setting

- Occupancy time delay,

Pulse mode, IQ mode

US Quattro COM2-24

DT Quattro COM2-24

US Oneway COM2-24

US Hallway COM2-24

1 low voltage switching output

operating in relation to the

detection of motion and ambient

light level. An additional isolated

normally open and normally

closed set of dry contact closures

for signaling HVAC (heating/venti-

lation/airconditioning) in relation

only to the presence of persons.

Settings:

- Light level setting

- Occupancy time delay,

Pulse mode, IQ mode

- HVAC stay-'ON' time

- HVAC switch-'ON' delay,

Auto-HVAC mode

US Quattro DIM-24

DT Quattro DIM-24

US Oneway DIM-24

US Hallway DIM-24

1 low voltage switching output

operating in relation to the

detection of motion and ambient

light level. An additional isolated

1-10 volt dimming output operat-

ing in relation to the amount of

daylight present.

Settings:

- Light level setting

- Occupancy time delay, IQ mode

- Stay 'ON' time DIM before 'OFF'

- Constant light level DIM

control option

- 8 -

Note:

1.) Tangential

- motion perpendicular to

the sensor

2.) Radial

- motion either directly

toward or away from

the sensor

3.) Presence

- minor motion as described

by NEMA WD7 with the

additional requirement of

both radial and tangential

detection

Ultrasonic signal can be increased

by hard surfaces and decreased

by soft surfaces.

US Oneway / US Hallway Ultrasonic Detection m

45.5

42.5

32.5

29.5

19.5

16.5

6.5

3.3

6.5

16.5

19.5

29.5

32.5

42.5

45.5

Coverage diagram

at 9 ft mounting

height.

One grid line = 1 m / 3.3 ft

US ONEWAY

US HALLWAY

Detection Zone

19.7

9.5

6.5

3.3

6.5

9.5

19.7

6 5 4 3 2 1 0 1 2 3 4 5 6

US Quattro / DT Quattro Ultrasonic Detection / DT Quattro Infrared Detection

Coverage diagram

at 9 ft mounting

height.

One grid line = 1 m / 3.3 ft

PIR RADIAL & PRESENCE DETECTION

PIR TANGENTIAL DETECTION

US TANGENTIAL & PRESENCE DETECTION

US RADIAL MAJOR MOTION DETECTION

- 9 -

COM1-24 Wiring



10.1

Note: Power Pack must be in Auto mode.

US Quattro COM1-24

DT Quattro COM1-24

US Oneway COM1-24

US Hallway COM1-24

18 AWG wire is recommended

for low voltage sensor & power

pack connection.

The leads consist of five wires:

1. 24V Input (RED)

2. Control Return (BLUE)

3. Communication (BROWN)

4. Switch Input (GREEN)

5. 24V Common (BLACK)

Load

Control Pro

COM1-24

Presence Detector

Control Pro

COM1-24

(Master)

Presence Detector

Control Pro

COM1-24

(Slave)

Presence Detector

Power Pack

Neutral

Hot

Neutral

Hot

White (Neutral)

Black (Hot)

Red (Relay)

Red (Load)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Green (Switch Input)

Brown (Communication)

White (Neutral)

Black (Hot)

Red (Relay)

Red (Load)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Green (Switch Input)

Brown (Communication)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Green (Switch Input)

Brown (Communication)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Gray (Momentary Switch)

(Optional Line Voltage

Maintained Contact Switch)

(Optional Line Voltage

Maintained Contact Switch)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Gray (Momentary Switch)

- 10 -

COM2-24 Wiring



10.2

Note: Power Pack must be in Auto mode.

US Quattro COM2-24

DT Quattro COM2-24

US Oneway COM2-24

US Hallway COM2-24

18 AWG wire is recommended

for low voltage sensor & power

pack connection.

The leads consist of eight wires:

1. 24V Input (RED)

2. Control Return (BLUE)

3. Communication (BROWN)

4. Switch Input (GREEN)

5. 24V Common (BLACK)

6. HVAC Relay Normally Open (YELLOW WITH RED STRIPES)

7. HVAC Relay Normally Common (YELLOW)

8. HVAC Relay Normally Closed (YELLOW WITH BLACK STRIPES)

Neutral

Hot

White (Neutral)

Black (Hot)

Red (Relay)

Red (Load)

Load

(Optional Line Voltage

Maintained Contact Switch)

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Gray (Momentary Switch)

Power Pack

Control Pro

COM2-24

Presence Detector

Blue (Control)

Black (-24 VDC)

Red (+24 VDC)

Green (Switch Input)

Brown (Communication)

HVAC Yellow/Red (Normally Open)

HVAC Yellow (Relay Common)

HVAC Yellow/Black (Normally Closed)

Isolated HVAC

Relay Contacts

max. 1 A Resistive load

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere STEINEL Sicherheitssensor Handbücher

STEINEL

STEINEL DUAL HF COM 1 Bedienungsanleitung

STEINEL

STEINEL IR Quattro COM 1 AP Bedienungsanleitung

STEINEL

STEINEL HF 3360 COM1 Betriebsanleitung

STEINEL

STEINEL IR Quattro SLIM Series Bedienungsanleitung

STEINEL

STEINEL HF 360 Bedienungsanleitung

STEINEL

STEINEL True Presence COM1 Bedienungsanleitung

STEINEL

STEINEL IS 180-2 Bedienungsanleitung

STEINEL

STEINEL IS 2160 ECO Kurzanleitung zur Einrichtung

STEINEL

STEINEL StudioLine IS 2160 Bedienungsanleitung

STEINEL

STEINEL IS 180 digi Bedienungsanleitung

STEINEL

STEINEL IS 140-2 Z-Wave Betriebsanleitung

STEINEL

STEINEL HF 3360-R PF UP WS Betriebsanleitung

STEINEL

STEINEL Multisensor True Presence DALI-2 IPD Bedienungsanleitung

STEINEL

STEINEL IS-FS 300 Bedienungsanleitung

STEINEL

STEINEL sensIQ Bedienungsanleitung

STEINEL

STEINEL IS 240 DUO Betriebsanleitung

STEINEL

STEINEL IS 240 DUO Bedienungsanleitung

STEINEL

STEINEL IS 1 Bedienungsanleitung

STEINEL

STEINEL MotionSwitch LED Z-Wave Bedienungsanleitung

STEINEL

STEINEL HF 3360 Betriebsanleitung

STEINEL

STEINEL IS 1 Bedienungsanleitung

STEINEL

STEINEL DALI-2 IS 3360 Betriebsanleitung

STEINEL

STEINEL StudioLine IS 2160 Bedienungsanleitung

STEINEL

STEINEL Professional Series Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung