STEINWAY LYNGDORF Steinway & Sons P100 Bedienungsanleitung
Steinway & Sons Model P100
OWNER’S
MANUAL
Version 1.0
2
Table of Contents
Compliance .......................................................................................................... 4
Pre-Installation ..................................................................................................... 5
Unpacking the Product ..................................................................................... 5
Operating Voltage ............................................................................................ 5
Ventilation Requirements ................................................................................. 5
Heat output ....................................................................................................... 5
Home Automation System Integration ................................................................. 6
Preparing the Model P100 for Mounting in a Rack .............................................. 7
Rear Panel ........................................................................................................... 8
Remote ................................................................................................................ 9
How to Pair Remote ....................................................................................... 10
Switching Remote to RF and IR Mode ........................................................... 10
Setup Procedure ................................................................................................ 10
Installation Via Web Interface ............................................................................ 11
Source ................................................................................................................ 11
Create ............................................................................................................. 11
Edit ................................................................................................................. 12
Arrange ........................................................................................................... 12
Delete ............................................................................................................. 12
Speaker and Room ............................................................................................ 13
Speaker Configuration .................................................................................... 13
RoomPerfect™ ............................................................................................... 13
Media Player ...................................................................................................... 14
How to Set Up RoomPerfect™ .......................................................................... 15
Volume Setting ............................................................................................... 15
RoomPerfect™ Preparations ......................................................................... 15
Placing the Microphone in the Focus Position ............................................... 15
Measuring the Focus Position ........................................................................ 16
Measuring Random Room Positions .............................................................. 16
Room Measurements Above 90% RoomKnowledge ..................................... 17
3
Audio Setup ....................................................................................................... 19
Audio Processing ........................................................................................... 19
Voicing Setup ................................................................................................. 19
Zone B ............................................................................................................... 19
Setup .............................................................................................................. 19
System Configuration ......................................................................................... 20
General Setup ................................................................................................ 20
Trigger In Setup .............................................................................................. 20
Trigger Out Setup ........................................................................................... 20
Network Configuration .................................................................................... 21
Streaming Setup ............................................................................................. 21
Manage Software ............................................................................................... 21
Software Information ...................................................................................... 21
Network Information ....................................................................................... 21
Backup ........................................................................................................... 21
Restore ........................................................................................................... 21
Factory Reset ................................................................................................. 21
Software Update ............................................................................................. 22
Troubleshooting ................................................................................................. 23
RoomPerfect™ ............................................................................................... 23
Network Setup ................................................................................................... 25
Connecting to Model P100 with a Network Cable .......................................... 25
Set Up a Fixed IP Address in Windows XP or Windows 7 ............................. 26
Trademarks ........................................................................................................ 27
Service Information ............................................................................................ 27
4
Compliance
WEEE
The European Parliament and the Council of the European Union have issued the Waste Electrical
and Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and
electronic equipment and to promote reuse, recycling, and other forms of waste recovery. Steinway
Lyngdorf products and the accessories packed with them are subject to the WEEE Directive. Please
dispose of any waste materials in accordance with your local recycling regulations. Products and
equipment which must be collected for reuse, recycling, and other forms of recovery are marked with
the icon of the crossed-out waste receptacle.
FCC
Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference; and (2) this device must accept any interference received, including any interference
that may cause undesired operation. Model A1/A2 amplifier and Model P100 processor contain TX
FCC ID: TYOJN5139M0.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. Equipment marketed to a consumer must be capable
of complying with the necessary regulations in the configuration in which the equipment is marketed.
5
Pre-Installation
Please read all material carefully prior to installation. If you need additional assistance, contact your
Steinway Lyngdorf representative or email [email protected].
Unpacking the Product
Carefully remove the unit and accessory kit from the carton and check for shipping damage. Contact
both the shipper and your Steinway Lyngdorf representative immediately if the unit bears any sign of
damage.
Note: Keep the shipping carton and all packing material for future use. If this unit is
shipped without the original packing, damage could occur and void the warranty.
Inventory
Check the list below to ensure that all necessary product components have been delivered. Report all
discrepancies to your Steinway Lyngdorf representative immediately.
• Owner’s manual
• Power cord
• Link cable
• Remote
LED Signaling
Red: Standby / On
Orange: Switching on
Blinking: Updating software
Operating Voltage
Steinway Lyngdorf products must be connected to the mains power system only. The Model P100 will
automatically detect the voltage between 110-230v.
Ventilation Requirements
The Model P100 does not have a built-in fan, nor does it require special measures to ensure proper
heat dissipation. However, it should be placed according to the guidelines below:
• It should always have at least one inch of free space on all sides.
• It should be placed in an environment free of excessive heat.
• In a rack system, the Model P100 should be placed at the bottom of the rack.
Heat output
Maximum: 43W / 145 BTU/hr.
6
Cables and Plugs
Use only mains cables and power plugs approved by Steinway Lyngdorf. Using other types may
cause damage to the system and will void the warranty.
Connecting
For cabling between the processor and amplifiers, please use RJ45 to RJ45 B standard cables. Use
only cables and connectors approved by Steinway Lyngdorf. Poor quality cables may violate safety/
EMC regulations as well as cause noise and interference.
• For cable lengths less than 1 meter, use CAT5E/shielded CAT6 cable.
• For cable lengths of more than 1 meter, use double-shielded CAT5E cables.
• All RJ45 connectors should be shielded.
Please refer to the wiring diagram supplied by Steinway Lyngdorf to determine which cables you
need.
Home Automation System Integration
The Model P100 is compatible with home automation systems via the RS232 and network connector
on the rear socket panel. The Model P100’s IR and trigger connections can also be programmed for
use in a home automation system.
IP Control
Open a TCP connection on port 84 and use the same protocol as on the serial interface (see Model
P100 Serial Control Manual). Use Telnet, Putty, or similar programs to open the TCP connection.
If you do not know the IP address of the Model P100 on your local network, the Model P100 supports
Apple´s Bonjour Discovery service, which must be on the computer you want to set up the Model
P100 with. The software is built-in as part of the Apple OS X operating system (not iOS devices). For
Windows operating systems, the software can be found at http://www.apple.com/support/bonjour/
Pressing the OK button on the remote and toggling through Info will also display the current IP
address of the unit.
Access the Model P100 by going to http://P100.local in your browser.
7
Preparing the Model P100 for Mounting in a Rack
The Model P100 processor is equipped from the factory with feet for free-standing placement on a
shelf, table, or rack.
To install the Model P100 in a rack:
1. Turn the Model P100 upside down and place it on a stable, even surface.
2. The screws used to fasten the rack brackets to the bottom of the Model P100 are in the holes
designated for the brackets when the product leaves the factory.
3. Fasten the brackets for rack mounting to the Model P100.
4. Mount the Model P100 in a rack.
WARNING!
Never rest the P100 onto the front, as this will damage the volume wheel
8
Rear Panel
On the back of the Model P100, you will find a range of inputs and outputs:
• Various optical, coaxial, and analog stereo audio inputs.
• 3 HDMI inputs and 1 HDMI outputs, all 4K compatible.
• 1 trigger input and 4 trigger outputs.
• 2 IR inputs (IR in A and B) and 1 IR connector output (IR in B - duplicated).
• 1 LAN connectors, for Ethernet connection on the local network. IP control is supported.
• 2 USB connectors, for music file playback, software updating, etc.
• 1 streaming USB input.
• 1 SD card slot for storing backup data.
• 1 microphone input for the RoomPerfect™ room correction microphone.
• 1 RS-232 connector for serial control of the unit.
• 5 Digital Link outputs for connecting Steinway Lyngdorf’s amplifiers.
Note: Do not use the USB ports for charging smartphones and tablets.
In Standby mode, only LAN A is active; LAN B connector is not active.
9
Remote
The Model P100 comes with a dedicated RF and IR remote control for installations and everyday
use.
Setup Access the installation menu.
Standby Turn the Model P100 on and into standby.
Audio Access the post-processing menu.
PiP “Picture-in-picture” /not supported in P100.
Up/Down Move up and down in menus.
Browse available settings in a menu.
Toggles between the available RoomPerfect™ filters.
Left/Right Move left and right in menus.
Toggle between neutral and the available voicings.
OK Activate the info screen, indicating the status of the unit.
Select a menu and store a selected setting.
Back Return to the previous menu.
Menu Access the user menu.
SRC Access the source menu list.
Source -/+ Toggle between active sources.
Volume +/- Turn volume up and down.
Mute Mute and restore the sound.
Play/Pause Play/pause the currently playing track of the media player.
Skip Forward/
Backwards Skip in the current playlist in the media player.
10
How to Pair Remote
The remote control is paired to the Model P100 at the factory, and you only need to pair it again if you
have a new Model P100 or remote. To pair the RF remote control to a Model P100:
1. Turn on the Model P100.
2. Hold down Play & OK until the remote control´s green LED flashes.
3. Point the remote control at the Model P100 and hold it within 30cm / 1 foot of the front panel;
when the green LED stops blinking, the remote is connected via Zigbee.
4. The remote will be paired to the Model P100.
To reset the pairing of the remote control, press Back and OK until the red LED flashes twice.
Switching Remote to RF and IR Mode
To switch the remote from RF to IR mode, hold down OK and 1. The LED will flash red twice.
To switch the remote from IR to RF mode, hold down OK and 2. The LED will flash green twice.
Setup Procedure
Set up the Model P100 surround sound processor by following these steps:
1. Check that the mains voltage switch on the A1/A2 amplifiers is correctly set to either 115V or
230V.
2. ID-assign all Model A1/A2 amplifiers via dip-switches on the A1/A2 socket panel according to
the project-specific wiring diagram.
3. Connect speakers to the Model A1/A2 amplifiers.
4. Connect Model A1/A2 amplifiers to the Model P100 as shown in the project-specific wiring
diagram.
5. Connect all external equipment, such as a Blu-ray player or home automation system, to the
Model P100, including inputs, outputs, and mains.
6. Connect power to the Model P100, the amplifiers, and all connected audio and video sources.
7. Switch on the Model P100.
8. Access Installer menu via Web or the remote and OSD.
9. Go to Speaker and room - -> Manage and add the Speaker Configuration file from a USB
stick.
10. Verify speaker setup by going to Speaker and room, select your speaker configuration and
press Right on the remote to select the setup. At the bottom of the screen, select and press
Verify Speakers.
11. Check speaker phases
12. Run RoomPerfect™ Guided Setup.
13. Set up sources, zones, etc.
14. Save and back-up settings.
Inhaltsverzeichnis
Andere STEINWAY LYNGDORF Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
