STEINWAY LYNGDORF P1 Bedienungsanleitung

MODEL P1 SURROUND SOUND PROCESSOR

INSTALLATION MANUAL

VERSION 1.9

[Skriv tekst]

TABLE OF CONTENTS

TABLE OF CONTENTS......................................................................................2

INTRODUCTION.................................................................................................3

COMPLIANCE ....................................................................................................3

PRE-INSTALLATION..........................................................................................4

OPERATING VOLTAGE.....................................................................................7

VENTILATION REQUIREMENTS.......................................................................7

CABLE CONNECTIONS.....................................................................................7

HOME AUTOMATION SYSTEM INTEGRATION................................................8

IP CONTROL ......................................................................................................8

INSTALLATION...................................................................................................9

TROUBLESHOOTING......................................................................................36

NETWORK SETUP...........................................................................................38

POWER SUPPLY SPECIFICATIONS...............................................................42

TRADEMARKS.................................................................................................43

SERVICE INFORMATION ................................................................................44

INTRODUCTION

This Installation Manual was created to assist you with setting up and using your Steinway Lyngdorf

electronics and accessories.

Please read all material carefully prior to installation or first use of your Steinway Lyngdorf product. If

you need additional assistance, contact your Steinway Lyngdorf representative or email

service@steinwaylyngdorf.com.

COMPLIANCE

WEEE

The European Parliament and the Council of the European Union have issued the Waste

Electrical and Electronic Equipment Directive. The purpose of the Directive is to prevent

waste of electrical and electronic equipment and to promote reuse, recycling, and other

forms of waste recovery. Steinway Lyngdorf products and the accessories packed with them are

subject to the WEEE Directive. Please dispose of any waste materials in accordance with your local

recycling regulations. Products and equipment which must be collected for reuse, recycling, and other

forms of recovery are marked with the icon of the crossed-out waste receptacle.

FCC

Steinway Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation

is subject to the following two conditions: (1) this device may not cause harmful interference; and (2)

this device must accept any interference received, including any interference that may cause

undesired operation. Model A1/A2 amplifier and Model P1 processor contain TX FCC ID:

TYOJN5139M0

Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment. Equipment marketed to a consumer must be capable of

complying with the necessary regulations in the configuration in which the equipment is marketed.

PRE-INSTALLATION

Unpacking the product

Carefully remove the unit and accessory kit from the carton and check for shipping damage. Contact

both the shipper and your Steinway Lyngdorf representative immediately if the unit bears any sign of

damage. All Steinway Lyngdorf equipment is carefully inspected before leaving our factory. Note:

Keep the shipping carton and all packing material for future use or in the unlikely event that the unit

needs servicing. If this unit is shipped without the original packing, damage could occur and void the

warranty.

Inventory

Check the list below to ensure that all necessary product components have been delivered. Report all

discrepancies to your Steinway Lyngdorf representative immediately.

•Installation manual

•Power cord

•Link cable

•Installer remote

•RoomPerfect microphone

•Microphone cable

•Microphone stand

The Installer’s Kit

The Installer’s Kit contains the following items:

•Laptop

•Wireless router

•Installer remote

•RoomPerfect microphone

•Microphone cable

•Microphone stand

Rear Socket Panel

1. Component video input

2. Composite and S-video input

3. HDMI input and output (5 input and 1 output)

4. RS232 connector for home automation control

5. Network connection

6. USB service connection (SW updates/loading speaker setups)

7. Component video output (BNC: main / RCA: zone 2)

8. Composite output

9. S-video output

10. Compact flash card slot

11. Trigger and IR input/output

12. Multichannel analogue audio input

13. Microphone input for RoomPerfect™ calibration

14. Coaxial digital audio input

15. Connector for RF extender

16. Lyngdorf Digital Link output A, B and C

17. Mains input and on/off switch

18. Balanced analogue audio input

19. Stereo analogue audio input

20. AES/EBU digital audio input

21. Optical digital audio input

22. Zone 2 analogue audio output

LED signaling - P1

Red: Standby

Green: On

Blinking green: Switching on

Orange: Zone 2 active

Blinking red: Power failure

Blinking red/green: Update of software.

When update is complete, the P1 will automatically switch off and on again.

OPERATING VOLTAGE

Steinway Lyngdorf products must be connected to the mains power system only.

Note: it is of utmost importance that the mains voltage switch is set appropriately. Turning the

product on with the incorrect voltage setting will cause serious damage to the product. Use only mains

power cables and power plugs approved by Steinway Lyngdorf or you may cause damage to the

electronics and infringe the warranty.

VENTILATION REQUIREMENTS

Steinway Lyngdorf products do not have built-in ventilation, nor do they need any special cooling

systems for heat dissipation.

When installing this product in an open cabinet or elsewhere without rack mounts, keep a minimum

clearance of one inch on all sides. Do not install it in an environment that will expose it to excessive

heat.

CABLE CONNECTIONS

Cables and Plugs

Use only the power cables included with the product when connecting it to the mains. Use only mains

cables and power plugs approved by Steinway Lyngdorf. Using other cable and/or plug types will void

the warranty and may cause damage to the system.

Connecting

For cabling between the processor and amplifiers, please use RJ45 to RJ45 B standard cables.

•For cable lengths less than 1 meter, use CAT5E/shielded CAT6 cable.

•For cable lengths in excess of 1 meter, use double-shielded CAT5E cables.

•All RJ45 connectors should be shielded.

Please refer to the wiring diagram supplied by Steinway Lyngdorf to determine which cables you

need. Poor quality cables may violate safety/ EMC regulations as well as cause significant noise and

interference. Use only cables and connectors approved by Steinway Lyngdorf.

HOME AUTOMATION SYSTEM INTEGRATION

The Model P1 is compatible with home automation systems via the RS232 and network connector on

the rear socket panel. The P1’s IR and trigger connections can also be programmed for use in a

home automated system.

IP CONTROL

Open a TCP connection on port 50042 and use the same protocol as on the serial interface (see

Model P1 Serial Control Manual). Use Telnet, Putty, or similar programs to open the TCP connection.

If you do not know the IP-address of the P1 on your local network, the P1 also supports Bonjour

Discovery service to locate the P1 on the local network. Before connecting the Model P1 to the

network, please download and install Apple Inc.´s “Bonjour Print Services” software on the computer

you want to set up the Model P1 with. This software will make it easy to access the Model P1 on the

network. For Windows operating systems the software can be found at

http://www.apple.com/support/bonjour/.The software is built-in as part of the Apple Inc.´s Mac

operating system (not iOS devices).

INSTALLATION

Using in a Rack System

The Model P1 processor is equipped from the factory with feet for free-standing placement on a shelf

or table. However, the Model P1 can also be mounted in a rack, along with the amplifiers and other

connected sources. Before mounting the Model P1 in a rack, you must first remove the feet and

attach the brackets included with the Model P1 as shown in the illustration.

Turn the Model P1 upside down and place it on a stable, even surface. Using a TORX 10 screwdriver,

remove the screws and washers holding the feet in place (see illustration). Keep the feet, screws and

washers for future use. The screws used to fasten the rack brackets to the Model P1 are in the holes

designated for the brackets when the product leaves the factory. Remove these four screws from the

Model P1 using the same screwdriver you used to detach the feet from the Model P1. Fasten the

brackets for rack mounting to the Model P1 as shown. You can now mount the Model P1 in the rack

using the screws included with the rack system you have chosen.

Reminder:

•The Model P1 should always have at least one inch of free space on all sides;

•Should be placed in an environment free of excessive heat;

•When placed in a rack system, Model P1 should be placed at the bottom of the rack, with the

amplifiers above it. This allows for proper dissipation of the heat generated by the amplifiers

without adverse effects on the Model P1.

Andere Handbücher für P1

Inhaltsverzeichnis

Andere STEINWAY LYNGDORF Aufnahmegeräte Handbücher

STEINWAY LYNGDORF

STEINWAY LYNGDORF P200 Gebrauchs- und Wartungshandbuch

STEINWAY LYNGDORF

STEINWAY LYNGDORF P300 2.1 Bedienungsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF D Bedienungsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF P1 Bedienungsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF Steinway & Sons P300 Bedienungsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF P200 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch