Stellar labs 33-12511 Bedienungsanleitung

Splitter

1 input 4 outputs

3D Support

4K Support

Model: 33-12511

INTRODUCTION

Thank you for your purchase of the Stellar Labs Model 33-12511 HDMI Splitter. This splitter is designed

to simplify the use of multiple high definition A/V devices in a home theater system.

The 33-12511 allows one HD source device to support up to two HDTV displays, providing both

displays the same image quality as the source. As this supports HDMI 4K resolution and HDMI 3D

video format, it is compatible with all equipment currently manufactured.

The amplifier and equalizer functions offer solutions for Home Theater, AV installation data center,

information distribution, conference room presentation, school and corporate training environment.

FEATURES AND CONTENTS

For the best performance of this HDMI splitter box, please read this manual carefully and

eep it for further information.k

Features:

HDMI 3D video format supported

Fully support 4K×2K HDTV

Pixel Clock Rate: 25 ~ 340 MHz

Quick reset key for splitter re-initiation

Dual detection mode selection (A/B Switch)

Compliant with DTS-HD®, Dolby®TrueHD lossless compressed digital audio

Support HDCP compliant devices

Gold plated connectors

Amplifier and Equalizer functions enable longer HDMI cable

Distribute HDMI signal up to 4 display devices

Fashionable metal housing design, free of interference

Content of Package

DC 5V power adaptor

HDMI Splitter main unit

User’s manual

CONNECTION

Connect the HDMI Splitter to your devices

1. Connect the HDMI cable from the HD source to the input port of HDMI Splitter.

2. Connect the HDMI cables from your displays (monitor or projector) to the outputs of the HDMI

Splitter.

3. Select one of the detection modes. Please refer to QUICK DETECTION MODE SELECTION below.

4. Plug the 5VDC power supply into the HDMI Splitter and turn on the power switch.

5. When connections are completed, the HDTV signal will be distributed to each HDTV display.

6. For the best performance, you can press the RESET key once to re-initiate the HDMI splitter, if the

HDMI connection is changed. It can make sure the Splitter is working well in HDCP between HD

player and display devices.

QUICK DETECTION MODE SELECTION

HDMI Splitter Source Device

Auto Detection & Auto Adjustment

Detection Mode Mode Action Suggested

Application Supported Not Supported

(Highest

Common Factor

Mode)

Auto detection,

Lower Standard

First

TV wall application,

sports bar application,

or other application

that different standard

(Resolution, Color

Deep) HDTVs are

connected together.

The HDMI Splitter will

compare the EDID

information of each sink

device (HDTV). A lower

standard sink device will be

set as the primary sink

device to communicate with

the source device.

The output resolution

and color deep of the

source device need to

be set first.

* Check the operation

manual of source

device for setting.

(Priority Mode)

Port 1~4 detection

sequence, First

Detect First Out

Home Theater

Application, or user

assigns a primary sink

device by connect it to

port 1.

Detection Sequence starts

from port 1. When connect

a sink device to port 1, the

device will be detected. The

source device will set the

output signal based on port

1 (primary sink device).

The output resolution

and color deep of the

source device need to

be set first.

* Check the operation

manual of source

device for setting.

HDMI connections require the EDID and HDCP information of source and sink devices for

successful communications.

Please check if the source devices (ex. Blue-ray DVD Player) support auto detection and auto

adjustment of resolution, color deep and audio format.

The mode selection switch is located at the rear panel of the Splitter box.

The original mode setting is mode A.

Please make sure all source and display devices (TV, Blue-ray player, projector…) support the

same 3D format while choosing mode A for play.

HDMI 3D video format:

Frame packing Side-by-Side (Half) Top-and-Bottom

[email protected]/24Hz 1920x1080i@59.94/60Hz [email protected]/24Hz

[email protected]/60Hz 1920x1080i@50Hz [email protected]/60Hz

1280x720p@50Hz 1280x720p@50Hz

QUICK START GUIDE

he connection illustrations are for reference only. Users may change the connection.T

A. TV Wall / Multi-Room / Sports Bar Application:

1. Set the HDMI Splitter in Detection Mode A.

2. Blue-ray DVD player set to AUTO video (resolution / color deep) and audio detection.

3. Connect all HDTVs to the HDMI Splitter; please check Figure 1 for your reference.

. Connect the power adaptor to the HDMI Splitter and turn ON the power of the HDMI splitter.

Figure 1

※If the Blue-ray DVD Player DO NOT support auto detection, please:

(1) Set the output signal of the Blue-ray DVD player to match with the lower standard HDTV to ensure all

HDTVs can display same images. In the case of figure 1, it will be HDTV 2 (720p/8-bit).

(2) OR set the HDMI Splitter in Detection Mode B, and set the output signal of the Blue-ray DVD player

to 720p/8-bit. Connect the HDTV 2 (720p/8-bit) to port 1.

※3D Application:

(1) Please make sure your Blue-ray player and all the HDTVs can support the same 3D format.

(2) Under Mode A, if there is any of HDTVs cannot support either 3D application or the same 3D format,

all of the HDTVs will be displayed in 2D. If the supporting 3D format of the Blue-ray player cannot be

compliant with one or some of the 3D HDTVs, the incompatible 3D TVs would not be able to correctly

show the 3D image.

B. Home Theater Application:

1. Set the HDMI Splitter in Detection Mode B.

2. Blue-ray DVD player set to AUTO video (resolution / color deep) and audio detection.

3. Connect the Home Theater Receiver, Projector, and HDTV to the HDMI Splitter; please check

Figure 2 or Figure 3 for reference.

4. Connect the power adaptor to the HDMI Splitter and turn on the power switcher.

Out 3

Out 4

Detection Mode Selection Out 2 Out 1

HDTV 1

(1080p/8-bit)

HDTV 3

(3D, 4K 2K)

HDTV 4

(3D, 4K 2K) HDTV 2

(720p/8-bit)

Primary

3D Blue-ray DVD player

Power adaptor

Figure 2

Figure 3

※ Blue-ray DVDs disc may support different audio format (PCM; Bit Stream: Dolby, DTS…etc.),

please set the Blue-ray DVD player to the correct audio format setting or set it to auto detection.

Please follow the user’s manual of your Blue-ray DVD player to change the output setting.

※ 3D Application:

(1) Please be sure your Blue-ray player and all the HDTVs can support the same 3D video format.

(2) Under Mode B, the device connected to output port 1 (TV, projector, amplifier, etc.) will be the

primary device for output standard.

- If the device connected to output port 1 equipped with 3D function, the Blue-ray player also

supports 3D, then 3D format will be selected as output format.

- If the source connected to output port 1 is a 2D device, the 2D format will be used for all the

outputs.

(3) When 3D HDTV or projector is used with a Home Theater Receiver, the Home Theater Receiver

needs to support 3D format as well, otherwise the Home Theater Receiver would have no audio

output. In this case, please change the play mode from 3D to 2D.

Detection Mode Selection

Home Theater

Receiver (1080p)

(Primary)

HDTV 1

(1080p/12-bit)

HDTV 2

(1080p/8-bit) Projector

(1080p)

3D Blue-ray DVD player

Power adaptor

Out 3

Out 4 Out 2 Out 1

3D 3D 3D 3D

Detection Mode Selection

Home Theater

Receiver (1080p)

(Primary)

HDTV 1

(1080p/8-bit)

HDTV 3

(1080p/8-bit)

HDTV 2

(1080p/12-bit) Projector

(1080p)

3D Blue-ray DVD player

Power adaptor

Out 3

Out 4 Out 2 Out 1

3D 3D 3D 3D 3D

DETAIL DETECTION MODE SELECTION

Mode A: (Highest Common Factor Mode)

Auto Detection, Lower Standard First

It is recommended to use Mode A for TV wall application, sports bar application, or other

application when different standard (resolution, color deep) HDTVs are connected together.

Source device supports Auto Detection and Auto Adjustment. (Please make sure

the auto functions are active.)

The HDMI Splitter will compare the EDID information of each sink device (HDTV). A lower

standard sink device will be set as the primary sink device to communicate with the source device.

For example, 4 HDTVs are connected to the HDMI Splitter with a Blue-ray DVD player, which supports

auto resolution / color deep detection and auto output signal adjustment. One of the 4 HDTVs supports

resolution in 720p and color deep in 8-bit, two support resolution in 1080p and color deep in 8-bit, another

HDTV supports resolution in 1080p and color deep in 12-bit. The HDTV that has lower resolution and

color deep will be set as the primary HDTV. And the Blue-ray DVD player will automatically deliver

720p/8-bit signal to all connected HDTVs. (Figure 4) If all the connected devices support 3D format, the

system will automatically take 3D play mode as a prior option.

When a new HDTV is connected to the system or the connection is changed, the Splitter will

detect the EDID of the newly connected HDTV.

If the newly connected HDTV supports lower standard in resolution or color deep, the

source device will adjust the output signal to match the HDTV. The picture on every HDTV will

disappear for a few seconds. If the new HDTV supports higher standard, the picture quality on

every HDTV will not change.

Figure 4

HDTV 2 is selected as the primary

sink device.

Blue-ray DVD player delivers

720p/8-bit signal automatically.

Source device DOES NOT support Auto Detection and Auto Adjustment.

The source device will send the signal as the setting of source device. Please set the

output resolution of the source device first, and make sure the resolution can be displayed on all

connected display devices.

For example, 4 HDTVs are connected to the HDMI Splitter which is connected with a Blue-ray

DVD player which DOES NOT supports HDTV resolution / color deep auto detection and auto output

signal adjustment; one of the HDTV supports resolution in 720p and color deep in 8-bit, two of the HDTVs

support resolution in 1080p and color deep in 8-bit, another HDTVs supports resolution in 1080p and color

deep in 12-bit. (Figure 5)

In order to have all HDTVs working, please set the output resolution to 720p and set the

color deep to 8-bit; otherwise some HDTVs will not show picture. Also, if the 3D Blue-ray player

was set 3D mode for play at first, the HDTV or projector without supporting 3D play function would

not be able to show 3D content appropriately.

Out 3Out 4 Out 2 Out 1

HDTV 1

(1080p/8-bit)

HDTV 3

(1080p/8-bit)

HDTV 4

(1080p/12-bit) HDTV 2

(720p/8-bit)

Primary

3D Blue-ray DVD player

Power adaptor

Figure 5

HDTV 2 is selected as the primary

sink device.

Set the Blue-ray DVD player to

deliver 720p/8-bit signal manually.

Mode B: (Priority Mode)

Output Port Detection Sequence, First Detect First Out

The detection priority is from port 1 to port 4.

It is recommended to connect lower standard HDTV to port 1 to make sure all connected

HDTV can display same image.

Users can assign one sink device (HDTV, Home Theater Receiver or Projector) as the primary

sink device by connecting it to port 1.

Source device supports Auto Detection and Auto Adjustment. (Please make sure

the auto functions are active.)

Sink device that connects to port 1 will be the primary sink device. The source device will set

the output signal based on the primary sink device.

Source device DOES NOT support Auto Detection and Auto Adjustment.

Please set the output resolution and color deep of the source device first, and make sure the

resolution and color deep can be displayed on all connected display devices.

For example, if you set the output resolution and color deep of the Blue-ray DVD player to 1080p

and 8-bit, please make sure all the HDTVs can display 1080p/8-bit (resolution/color deep). If any

connected display device can not support 1080p/8-bit (resolution/color), this HDTV will not show pictures.

(Figure 6)

Figure 6

The detection priority:

Output port 1 to 4

Out 3Out 4 Out 2 Out 1

HDTV 1

(1080p/8-bit)

HDTV 3

(1080p/8-bit)

HDTV 4

(1080p/12-bit) HDTV 2

(720p/8-bit)

Primary

3D Blue-ray DVD player

Power adaptor

Out 3Out 4 Out 2 Out 1

3D 3D 3D 3D

HDTV 1

(1080p/8-bit)

Primary

HDTV 3

(1080p/8-bit)

HDTV 4

(1080p/12-bit) HDTV 2

(1080p/8-bit)

3D Blue-ray DVD player

Power adaptor

TROUBLE SHOOTING

1. When there is no picture presented, please:

Make sure the direct connection from the source device to the display device without the HDMI

Splitter is working.

Check all the connection is correct and all connectors are connected well.

Check the quality of connected cable, and make sure the cable does not damage.

Change the connection sequence of display devices.

Make sure the output resolution of source device can be displayed on all connected display devices.

Reset the HDMI Splitter.

2. How to make sure your input and output devices are suitable with the HDMI Splitter?

Whether all devices are HDCP compliant?

Whether all HDMI cables stay in good quality as well as connectors?

Make sure all HD displays support the same resolution (720p, 1080i, or 1080p).

3. Some of the connected HDTVs show “mode not support”, some HDTVs are working well.

Make sure all HD displays support the same resolution (720p, 1080i, or 1080p) and color deep (8-bit,

10-bit, and 12-bit).

The HDTVs which show “mode not support” may support low color deep.

Try to change the detection mode to Mode A,

Or set to Mode B and then connect one of the non-working HDTV to output port 1.

4. When there is only picture displayed and without sound:

Check all the connection is correct and all connectors connect well.

Check if you connect any DVI interface display device to the splitter, the splitter may use the EDID

information of the DVI interface display device as communication standard. DVI supports only video

transmission. Please change the connecting sequence, and reset the HDMI Splitter. Make sure the

connection is in the HDMI standard.

Check your cable to see if it supports video transmission only or it is damaged.

HDCP may not match well at first connection. Please press the reset key to reset the HDMI Splitter.

Do you connect any recorder that does not support HDCP to the output port of HDMI Splitter? HDCP

may lock up audio part.

5. HDTV and Blue-ray DVD player can support up to 1080p/12-bit, but when I set the Blue-ray DVD player

to auto detection, it always deliver 1080p/8-bit video signal.

Disable the auto detection function of the Blue-ray DVD player, and set the output resolution and

color deep to 1080p/12-bit. (If other connected sink devices can not support 1080p/12-bit video

signal, the sink devices will not show image.)

6. Snowing noise or image interruption occur when use 1080p/12-bit output setting.

Make sure the HDMI cable is capable of transmitting 1080p/12-bit video signal. A High Speed Rated

HDMI cable is recommended.

7. When resolution could not show in 1080p?

Make sure your sources (HD Player) and displays are fully supporting 1080p.

8. A HDTV and Home Theater Receiver are connected to the HDMI Splitter, but the receiver delivers stereo

audio to the audio amplifier instead of HD audio (Dolby TrueHD, DTS HD).

The primary sink device may set to the HDTV which may only support stereo audio. Please set the

detection to Mode B. Connect the Home Theater Receiver to port 1, and connect the HDTV to port 2

or other ports. The Home Theater Receiver will be set as the primary sink device.

9. When 3D content could not be shown on your display.

Please make sure your source and displays support 3D and also support the same 3D format.

Please check the play mode of Blue-ray player has been set 3D or AUTO mode for video output.

Please make sure the video content is 3D content.

10. If the presented picture is not a proper 3D image, please check whether the 3D format of 3D Blue-ray

player and TV (projector) are correct setting.

11. If the presented picture is symmetric, which showed with up and down or right and left symmetric

image, please check whether the TV or projector supports 3D display function and make sure the

function is enabled. If the TV or projector does not support 3D video format, please turn off the 3D play

mode of 3D Blue-ray player.

NOTICE

Manufacturer reserves the right to make changes in the hardware, packaging and any accompanying

documentation without prior written notice.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing LLC in the United States and other countries.

33-12511 incorporates HDMI®technology.

Trademarks and brand names are the properties of their respective owners.

Dolby is a registered trademark of Dolby Laboratories.

DTS is a registered trademark & the DTS logos and Symbol are trademarks of DTS, Inc.

Inhaltsverzeichnis

Andere stellar labs Kabel und Steckverbinder Handbücher

stellar labs

stellar labs 33-12506 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung

stellar labs 33-12511 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken