STIEBEL ELTRON CNS 75 FG Bedienungsanleitung

CNS 75 FG, CNS 100 FG, CNS 125 FG,

CNS 150 FG, CNS 175 FG, CNS 200 FG

2 - 5

English

6 - 9

Freestanding &Wall mounted convector heater

Operating and installation instructions

中文

立地&壁挂型对流式电暖器

使用与安装说明书

1.3 Safety notes

The appliance must not be operated:

– In areas which are subject to the risk of ﬁre

or explosion due to chemicals, dust, gases

or vapours;

– In the immediate vicinity of pipes or

containers which carry or contain combus-

tible or potentially explosive substances.

For this reason, the minimum clearance

intervals must not be undercut.

In workshops or other areas in which the

odour of waste gases, oil, petrol, etc. might

occur, or in which work is carried out

involving solvents and chemicals, there is a

risk of sustained odour burdens being eng-

endered, and possibly of dirt contamination

occurring.

The air outlet must not be obstructed. For

safety reasons the upper and lower air grilles

must never be covered with items such as was-

hing nor obstructed by items in too close

proximity (see ﬁgure 3). Objects should not be

leant against the unit nor placed between the

unit and the wall. Never leave combustible

materials, such as wood, paper, textiles or

ﬂammable items such as wax, petrol, aerosol

cans etc. in the vicinty of the warm air outlet.

1.1 Switching on the Unit

The unit may be switched on (settingI) or oﬀ

(settingO) by using the switch (1) on the right

hand side panel.

1.2 Heater

Turning the temperature selector (2) to the left

will turn on the heater and select the required

temperature. Once turned on, the heater will

warm the room uniformly and quickly.Air enters

the heater from below where it is heated and

then exits through the grid at the top of the

heater.The room temperature can be inﬁnitely set

between approx. 6 °C and 30 °C.The thermostat

switches the heater oﬀ once the set temperature

has been reached and switches on and oﬀ inter-

mittently to maintain the required temperature.

If uniform temperature is required in two rooms,

do not set both heaters to the same setting.The

same applies to two heaters installed in the same

room.

In order to minimize energy usage when airing

the room by opening the windows, it is advisable

to switch oﬀ the unit.

1.2.1 Anti-frost setting

Set the temperature selector (2) to .

The thermostat will switch the heater on auto-

matically if the room temperature drops below

approx. +6 °C. Ensure the correct heater is ﬁtted

to cope with the demands to be made upon it.

1.2.2 Limiting the temperature range

In order to lock the selector at a speciﬁc tempe-

rature, remove the two pins (3) from the rear of

1. Operating instruction for the user and the professional

the housing and insert either side of the desired

setting.The two pins may also be used to limit a

temperature range.

Warning:in order to avoid overheating, do not

cover the heater.

Attention!

The installation, electrical connection and ﬁrst

operation of this appliance should be carried

out by a qualiﬁed installer.

The company does not accept liability for

failure of any goods supplied which have not

been installed and operated in accordance

with the manufacturer's instructions.

This convector heater must be installed by an

authorised serviceman in conjunction with these

instructions.

These installation instructions belong to the

heater and must be handed on to the successor

if the heater is sold.

Stiebel Eltron convector heaters are direct

electric heaters designed to be mounted on the

wall and are particularly suitable for heating

smaller rooms such as utility rooms, kitchen, bath-

and washrooms etc.

The convector heater is supplied with a lead.

The convector heater must not be mounted

immediately below a wall socket.

Use the wall-mounting bracket as a template for

positioning the heater correctly and providing the

correct distance from the ﬂoor.

Place the bracket on the ﬂoor. Mark the screw-

holes through the drill holes ( 1 ).

Raise the bracket and position it in such a way

During the just operation,the heater may

give oﬀ a smell.Ensure that the room is

ventilated (for example, open a window).

2.1 Attaching the wall mounting

bracket

The wall mounting bracket is oriented centrally

(see ﬁgure and the following table).

2.Installation instructions for the professional

As with all similar heaters, the ﬂow of rising air

may cause discoloration of the wall.

Before using any materials which

produce ﬂammable gases or vapours,

e. g. laying or sealing parquet or PVC ﬂooring, or

when using spray polishes, spirits and similar

materials, ensure the heater is switched oﬀ.

1.4 Servicing

Do not use abrasive or aggressive cleansers to

clean the heater.

Use a vacuum cleaner regularly to clean the

upper and lower air grids.

ilgnE

Type CNS CNS CNS CNS CNS CNS

75 FG 100 FG 125 FG 150 FG 175 FG 200 FG

Output Power (220V) W 686 915 1144 1372 1601 1830

Output Power (230V) W 750 1000 1250 1500 1750 2000

Width mm 445 445 590 590 740 740

Heigth mm 450 450 450 450 450 450

Depth mm 78 78 78 78 78 78

With wall mounting 100 100 100 100 100 100

Measure Amm 195 195 343 343 491 491

that holes Bare aligned with the marks on the

wall you have just made. Now mark the upper

holes through holes Cand Din the wall

mounting (ΙΙ). Drill the four holes, insert plugs

and screw the wall mounting securely to the wall

using four screws.

2.2Wall mounting the convector

On the backside of the convector there are 4

slots, these should be hooked onto the wall

bracket and pushed down.The spring clips

should be turned clockwise to secure. To remove

the convector reverse the above operation.

2.3 Installation with feet

Unhook the wall mounting bracket.

Remove the two screws from the bottom

of the appliance.Fit the feet to the bottom

of the appliance in such a way that they are

inserted into the recess at the back of the

appliance。Secure the feet with the screws

you just removed.

2.4 Electrical connection

This heater is for 220V AC.

Please observe national standards, the regula-

tions of your local electricity supply company as

well as data the rating label.

Electrical safety!

The convector heaters have protective system II

( ) and are spray protected ( IP24 ).

Note the details on the rating plate!

The voltage supply must match the require-

ments on the rating plate.The supply cable must

be correctly sized.The heater must be connected

to a socket outlet or permanent terminal box at

least 10 cm to one side of the heater. Any visible

damage of the electrical connections must be

rectiﬁed by a qualiﬁed electrician!

Please note in general:

Where the convector heater is ﬁtted in a room

with a bath or shower, ensure the safety zone

deﬁned in IEE Regulations is applied in

accordance with the details on the rating plate.

The unit is to be ﬁtted in such a way that switch-

ing and control devices cannot be touched by

anyone in the bath or under the shower.

If the supply code is damaged, it must be repla-

ced by Stiebel Eltron company or its authorized

installer in order to avoid a hazard.

Do not use this heater with a programmer, timer

or any other device that switches the heater on

automatically,since a ﬁre risk exits if the heater is

covered or positioned incorrectly.

Do not use this heater with feets in the immediate

surroundings of a bath, a shower or a swimming pool.

English

Safety measures

This convector heater is equipped with a safety

cut-out that switches the heater oﬀ if it over-

heats. Once the heater has switched oﬀ due to

overheating, remove the cause of the fault, e. g.

blocked air grids.When the heater has cooled

down for several minutes it will restart auto-

matically. If the heater then cuts oﬀ again, switch

oﬀ the heater and call an authorised serviceman.

Caution! Ensure the safety zones (mm) in

following ﬁgure are kept free.

≤

≥001

1.3 安全注意事项

本产品严禁用在下述环境：

- 存有化学品，粉尘，煤气或蒸汽，可

能引发火灾，爆炸的地方。

- 紧邻装有易燃易爆物质的管道或容

器附近。

基于此原因，电采暖器必须和周围物体

保持一定的最小距离。

在具有废气，机油，汽油等气体挥发物

的车间或类似区域中，或者在此区域中

从事有关涉及溶剂和化学药品的工作时，

其所产生的挥发物气味会有被加强的风

险, 而且有可能产生一些污染物。

警告：为避免过热，禁止覆盖加热器。

出风口绝对不能被阻挡。基于安全原因，上

下进出风口的格栅绝对不能被物体覆盖，比

如湿毛巾。也不能将物体放置在距离进出风

口太近的位置，以免阻挡空气循环。(参见

图 3) 不要将物体倚靠在此电器上，也不要

在此电器和墙壁之间放置任何物品。绝对不

要将可燃物，如木材，纸张，纺织品或易燃

物品，如石腊，汽油,喷雾剂罐等置于热空气

出口附近。

1.1 接通电采暖器

此电采暖器的开关位于右侧(

) 。按到

开启电采暖器。按到位置关闭。

1.2 加热

将调温器(2)转向左边将会开启电采暖器而

且可以选择所需的温度。开启以后,电采暖

器将会均匀而且快速地使房间变暖。室内

空气从底部进入电采暖器，经过加热后再

从顶端的格栅排出。室温可以无级地设置

在大约6°C 到 30°C之间. 当室温达到设定的

温度后，温控器会自动关闭电采暖器。通

过这样间断地开启和关闭将房间温度保持

在所需的温度。

如果想要使二个房间具有均匀的温度,不要将

两台电采暖器设置在相同的设定。同样的原

则适用于在一个房间中安装二台电采暖器的

场合。

为了节约能源，当开窗通风时建议将电采暖

器关闭。

1.2.1 防霜设定

将调温器(2)旋转到位置。

如果室温下降到低于 +6 °C左右，调温器将

会自动开启电采暖器. 应根据所需要的热负

荷来选择正确的电采暖器型号。

1.2.2 限定温度范围

为了将温控器度锁定在特定的温度值，可

将温控器盒后面的两个顶针 (3) 取下并插入

1. 操作使用说明供用户和专业安装人员

到温控旋钮相应的孔中。这二个顶针也可以

用来设置温度限定范围。

位置

注意事项 !

此电采暖器的安装、电气连接以及第一次

运行都应该由合格的专业安装人员来进行。

对于因为未按照本说明书进行安装和操作

而导致产品的任何损坏，本公司将不予负

责。

此对流式电采暖器必须由授权的安装服务人

员按照这本说明书进行安装。

这本安装说明书属于此电采暖器的一部分，

如果电采暖器被转卖，应将说明书转给其

买者。

斯宝亚创对流式电采暖器属于直热式，设计

为墙壁安装。特别适用于较小的房间的采

暖，例如杂物间，厨房，卫生间和洗衣房等。

此对流式电采暖器随机提供有电源线插头。

此对流式电采暖器不得直接置于电源插座下

面。

墙壁挂架可用来作为一个模板，以便正确地

定位电采暖器和提供到地板的正确距离。

将挂架放在地板上。经过挂架上的钻孔在墙

上作打孔的标记。 ( ) 1

抬高挂架，使得两个孔B和你刚刚在墙上做的

在第一次运行时，此电采暖器可能会

产生一些异味。请确保房间通风。

(例如,打开窗户)

2.1 安装墙壁挂架

墙壁挂架和电采暖器是同心的。

(参见附图和下面的表格)

2. 安装说明供专业安装人员

和其他类似的采暖器具一样，此电采暖器产

生的上升热气流可能会导致墙壁变色。在使用任何会产生可燃气体或挥发物

的材料，如铺装木地板或PVC地板时

用的胶，或者喷涂上光剂、油精等类似物

品以前，应确认电采暖器已关闭。

1.4 保养

不要使用研磨性或腐蚀性的清洁剂来清洁此

电采暖器。

定期用吸尘器清洁采暖器的上下进出风口。

型号 CNS CNS CNS CNS CNS CNS

75 FG 100 FG 125 FG 150 FG 175 FG 200 FG

额定功率 (220V) W 686 915 1144 1372 1601 1830

额定功率 (230V) W 750 1000 1250 1500 1750 2000

宽度 mm 445 445 590 590 740 740

高度 mm 450 450 450 450 450 450

进深 mm 78 78 78 78 78 78

带有墙壁挂架 100 100 100 100 100 100

长度 Amm 195 195 343 343 491 491

文中

标记志对齐。然后再通过挂架的孔C和D在

墙上作标记。( )

ΙΙ

在墙上钻出这四个洞,塞入涨管然后用四个

螺钉将挂架扭紧在墙壁上。

任何电气联接上的可见损伤都必须由持证

电工进行维修。

2.2 将电采暖器挂到墙壁上

在电采暖器的背面有4个槽,将这些槽用墙壁

支架钩住然后推下。顺时针方向旋转卡簧将

电采暖器锁住。

要拆除电采暖器则逆着进行上述的操作

。

请注意产品铭牌上的详细信息！

供电电压必须和产品铭牌上的要求相一致。

供电电线应选用正确的线径尺寸。此电采

暖器必须被联接到距其任何一边10厘米以

上的墙壁插座或固定的电气终端盒中。

2.4 电气联接

此电采暖器采用220 伏交流电。

请查阅国家标准、当地电力部门的规定以及

产品铭牌上的数据。

电气安全！

此对流式电采暖器为电气双绝缘结构( )并

具有防溅保护( IP24)。

2.3 安装地脚

拆下墙壁安装支架，并从器具底部拆走两侧的

螺钉。

如图将地脚先插到器具后壳的安装孔中，然后

再利用拆下来的螺丝将地脚固定在器具上。

其它注意事项:

当此对流式电采暖器安装在装有浴盆和淋

浴喷头的房间中时，请根据产品铭牌中的

内容，确认IEE(国际电气工程师协会)规范

中关于安全区域的要求得到遵守。

电采暖器的安装要使得在浴缸内或淋浴区

的人不能够触及到开关和其它控制器。

如果电源软线损坏，为避免危险，必须由

斯宝亚创公司或其授权的专业维修人员进

行。

因为加热器的被覆盖或不正确的放置会引

起火灾危险，故不得利用带有可自动接通

电源的程序器、定时器或任何其他装置来

使用本加热器。

在浴缸、喷头或游泳池的四周不得使用带

地脚安装方式的加热器。

安全距离

此对流式电采暖器配备有安全保护开关，

当过热时会自动关闭采暖器。一旦发生采

暖器因过热而关闭的情况，应排除产生故

障的原因，如进出风口被遮闭。当采暖器

冷却下来以后几分钟，它将会自行重新开

启。如果随后采暖器的保护开关再次切断，

应关闭开关并联系授权的维修人员。

注意！

确保下图所标注的安全区域内(mm)没有任

何物体。

≤

≥001

文中

斯宝亚创(天津)电器有限公司

天津市西青经济开发区

赛达国际工业城C3-1，C3-2，C3-3 300385

电话: 022-83962077 传真: 022-83962076

电子邮件：[email protected]

网址：www.stiebel-eltron.com

制造商：

Manufacturer:

Stiebel Eltron (Tianjin) Electric Appliance, Co., Ltd.

10A Huiya Park, Xiqing Economic Development Area,

Tianjin China 300385

Tel: 86-22-83962077 Fax: 86-22-83962076

Email: in[email protected]

Web: www.stiebel-eltron.com

603 / K120065

Distributor:

Stiebel Eltron (Guangzhou)

Technology and Development Co., Ltd.

F 7/8, NO. 590, Yinbin Road, Panyu District

Guangzhou, PRC.

Tel: 020-6195 2996

Fax: 020-6195 2990

E-mail: in[email protected]

www.stiebeleltron.cn

www.stiebel-eltron.com

经销商：

斯宝亚创(广州)科技发展有限公司

中国广州市番禺区迎宾路590号邦耀大厦7、8楼

电话：020-6195 2996

传真：020-6195 2990

电邮：[email protected]

中文网址： www.stiebeleltron.cn

德国总部网址： www.stiebel-eltron.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere STIEBEL ELTRON Heizung Handbücher

STIEBEL ELTRON

STIEBEL ELTRON CNS 125 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CNS 100-2 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CNS 50 SE Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CK 20 trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CBS 20 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CNS 100 F Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON MHA Series Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CK 20 trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CK 20 Premium Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CS 20 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CON 5 Premium Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CNS 300 UE Kurzanleitung

STIEBEL ELTRON

STIEBEL ELTRON CWM 750 M-F Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON FCR 21/60 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Thermocon BHE 75 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON FCR 18/60 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CK 150-1 Plus Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CK 20 Plus AU Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON CNS 150 U Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON ETT 500 electronic Merkblatt

STIEBEL ELTRON

STIEBEL ELTRON BHE 75 Classic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SunWarmth CIR 150-1 O Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON ETS 300 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung