Stinger BS120 Bedienungsanleitung

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 1of 20

THE “STINGER” BS120 SECURITY FENCE ENERGISER.

This user friendly unit has been designed for ease of operation, reliability and Simple operation of the

controls.

A fully computer controlled and integrated perimeter protection system with multiple units is easy to

assemble.

The unit has the following features:

A novel alarm monitoring system (SA Patent No. 99/5728)capable of protecting up to 20 zones. An

alarm condition will occur if the fence live wire is either cut or short circuited during 3 consecutive

pulses in the same zone.

The HV monitor system ensures stable zone information with no drift due to temperature or

corrosion.

Zone programming is very simple.

Fence Voltage can be switched to ”Low Voltage” (800V) or ”High Voltage”(8500V)

A warning will be given if the fence voltage drops below a level of 3000V due to a system fault.

All controls are located on the remote control unit. Communication between this unit and the

energiser is via a RS485 data link (4 core comms cable), via an RF link or via fibre optic cable.

Multiple Remote Control Units can be connected to one BS120 unit, in which case any control unit can

be programmed to be the ”Master” control unit or a ”Slave” control unit. 

The remote control unit can address up to 13 energizers. If multiple energizers are selected,

synchronization can be automatically applied.



STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 2of 20

A UHF Transceiver with anti-collision facility can be supplied for bi-directional data

communication over distance s up to 4 km.

Windows 95/98/2000/NT/XP software is available to interface up to 125 

Energizers to a PC via a RS485 data cable, RF data transceivers, or fibre optic

cable.

Up to 125 Site maps can be stored. To enable security control of different sites by

one computer.

The output voltage of each energizer can be viewed at the LCD Panel and will also be

logged via the computer program.

The software allows for pulse synchronisation of multiple BS120 units.

The zones have to be series wired and must be series connected to each other.

The start and end points of the fence and the fence ground are the only

connections to the energizer. An additional feature is that the fence is powered from

both ends.

An auto-reset facility is available and can be enabled or disabled. The unit will

automatically try to reset an alarm after 3 minutes. If successful, the alarm was

apparently a nuisance alarm and no further action is required.

SPECIFICATIONS

Power

Input Voltage :110V-250V AC or 12V DC (Solar Panel)

Power Consumption :15VA

Built-in back-up Battery :7.5 A/H, 12V Lead Acid Battery.

Back-uptime> 5 hours

HV Output (High mode)

Output Voltage (open) : 8250V

Output Voltage (500 Ohms) : 7500V

Output Voltage (100 Ohms) : 6000V

Output pulse Energy : 7.5 J

Output pulse length (10% points) : 130s

Pulse Repetition Rate : 1.2 S

HV Output (Low mode) : 800V

Output pulse energy : 0.08 J

Max. length of live wire : 25 Km with max. wire resistance of

1000 Recommended < 500 Ohms)

Dimensions : 340 X240 X 130

Weight : 4kG

Watchdog

Built-in watchdog to prevent double pulsing and to limit max. Energy output.

The energizer will switch off if any of these conditions will occur and

will be indicated at the energizer board by leds.

The system complies with the following specifications:

IEC 60335-1, IEC 60335-2-76, IEC1000-3-2, IEC 61326-1, CISPR Pub. 14.

The system has been CE approved by the SABS, and the

CEcertificate is available on request.

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 3of 20

Control Inputs/Outputs on the Energizer unit:

External Siren connection : Contacts available for 12V/10W Siren. On—Time3 minutes or

terminated on “reset”.

Silent alarm connection : Contacts available for a 12V, max 1A load.System has to be reset

before a new alarm can be triggered.

Gate monitor connection : Input for n/c gate contact.

Alarm system : HV current monitoring system. A sequence of 3 identical faults

occurring in the same zone isrequired before an alarm condition will be

reported.

WINDOWS SOFTWARE PACKAGE

This package has been specifically designed for the ”Stinger” BS120 system, used on large sites with a

number of ”Stinger” units. The software is extremely versatile and is yet user friendly to the average

operator.

The program has the following general features

Can be loaded onto all modern machines and is Windows95/98/2000/NT/XP

compatible.

Communicates via the computer comm. port and

an RS485 to RS232 converter with up to 125 BS120 units via a two wire cable, RF data link or fibre optic

cable.

Full control of all units is possible via simple configure and setting-up windows.

Up to 125 site maps can be imported, indicating on the screen the physical positions of the”Stinger”

units and the Electric fence zones at the perimeter.

The location and the type of alarm condition will be shown at the site map for quick reaction by the

security personnel.

An alarm will be raised to alert the operator.

Feedback systems are built into the software to monitor the reactions of the

operating personnel.

A log file keeps record of all events and fence conditions and is available for later

retrieval. A printout can be made anytime of any part of this file.

Extensive protection in the software to counteract tampering with logged data.

The HV outputs of ”Stinger” units can be individually programmed to switch to high or low voltage at

selectable times and days.

It is possible via this program to synchronise a number of BS120 units to comply with Government

regulations.

The contents of the “Log file” can be downloaded to a remote computer if a telephone modem has been

installed.

Optional peripherals

-Mains modem for activating floodlights per zone or to communicate with a remote control unit via

mains communication.

-600 mW UHF TransceiverWith FSK modem. Can be used for data communication overdistances

up to 4 Km and more.

-Relay card. Provides 25 relay contact outputs for interfacing to e,g, existing alarm system, lights

etc.

-Stinger program extension is available to provide full SMS facility.

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 4of 20

Earthing practice

The above picture indicates how earthing should be done. This

picture only shows the earthing required to protect the energizer

against lightning. General fence earthing depends on external

factors like ground conduction etc.

Zone length: The best results will be obtained it the difference in

zone resistance is not more than 50%

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 5of 20

INSTALLATION TIPS:

The following tips will help to facilitate installation.

1 Using the best type of bobbins and strain insulators will result in a trouble

free installation. E.g. Stinger strain insulators and Stinger intermediate bobbins.

2 Using low resistance aluminum wire will result in effective shock delivery.

3 Grounding the fence at regular intervals results in high stability and better

shock delivery .

4 Early morning false alarms occur due to arcing. Check the fence currents

with the display unit in the Power mode. If the HV1 and HV2 values are

unstable, there is a weak point somewhere at the fence. (Cracked bobbin,

too short wire spacing at stays etc.).

5 Keep HT wires away from communication- and power cables.

6 Underground HT Cables should be mounted inside irrigation tubing/conduit.

7 If the distance between the fence and the location of the energizer is long,keep the

two HT wires separated by 200mm. Use braided bare copper for the ground wire,

burying it directly in the ground. This will ensure the best eathing possible.

If the distance between energizer and control unit is more than 10 meters, it is wise

to mount a copper braided cable together with the comms cable.Ground this copper

cable at both end points.

The following table shows the effect of the type of fence wire used in relation to

practically obtainable distances.

Fence wire resistance and compatibility with the BS120.

Type of wire

Resistance (Ω/Km)

Max tolerable live wire length

L(1/2V)*

Stainless 1.2mm

770

1.9 Km

0.65 Km

Braided 1.0mm

330

4.5 Km

1.6 Km

Braided 1.3mm

260

5.7 Km

1.9 Km

Galv steel 1.57mm

100

15 Km

5 Km

Galv steel 2.24 mm

30 Km (Practical limit 25 Km)

10 Km

Alu. 1.6mm

44 Km (Practical limit 25 Km)

13.5 Km

Alu 2.4 mm

133 Km (Practical limit 25 Km)

55 Km

*The value L(1/2V) is that length of live wire, where half of the energizer output

voltage drops across the fence wire and the other half across a person touching

thewire at distance L(1/2V). (Equals to only 25% of the potential energy at the

energizer output. This value relates to any energizer being used. The

resistance of ahumanbody has been standardized at 500 Ohms.)

8 Fence monitor lights : Recommended maximum three per BS120 Energizer, as each

fence monitor light draws +-0,4J.

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 6of 20

FENCE WIRING EXAMPLES

It is important to always loop the earth wires together at each zone

split.This will ensure maximum energy transfer.

For extremely long fences, or in situations where the fence

resistance becomes excessive high, wires can be connected

inparallel. It is in this case important that the parallel connections

are repeated at the end of each zone as shown above.

For more information please refer to “Stinger Specification for construction of

electric fencing” available on request.

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 7of 20

Long fences can be operated with multiple energizers, provided these units are

synchronized.

Stinger has SABS approval for such a system. Each energizer can feed one live wire.

The advantage of this system is that no trenching, cabling or solar panels are required,

as all units are located inside the guard house.

An additional advantage is the fact that the fence is much more secure in case of one

of the energizers failing.

Fences with a total circumference of 10 Km have been wired according to this system.

Sync Unit or

LCD Keypad

handling

multiple

energizers.

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 8of 20

OPERATING INSTRUCTIONS

Zone programming

Before starting, check the following fence conditions (with the HV wires

disconnected):

1. The DC resistance of the HV loop must be lower than 1200 Ohms.

2. The DC resistance between GND and the live wires must be higher than

100000 Ohms.

Programming

1. Switch the Energizer on to High Voltage Mode.

2. Press the “Program” button for 5 seconds. If the buzzer sounds, there is

a fence problem, which must be solved first. The problem may be a short

circuit or arcing.

3. Make a short circuit at zone split 1-2 (use the cable with crocodile clips),

the buzzer will sound, press the “Accept” button briefly.

4. Repeat step 3 until all zones have been programmed. After the last zone

press “Program” again to leave this routine. The remote control unit will

indicate the program status.

Remote Control Unit Connections

The standard connection cable can be extended to a length of a 100m.

This can be safely done if lightning in that area is not a problem.

Otherwise add a braided copper wire to the cable, which must be earthed at

both sides.

For longer distances the “Stinger” data radio should be used.

USE STINGER LIHGTNING DIVERTERS BETWEEN THE ENERGIZER GND CONNECTION AND THE

HV1 AND HV2 OUTPUTS.

USE A MAINS LIGHTNING PROTECTOR AT THE MAINS INPUT TO THE UNIT.

Connections

connector block:

1. Gate switch

2. Gate switch

3. Strobe light +

4. Strobe light –

5. Siren +

6. Siren -

Please note:

-The instrument is to be installed inside a building

or inside a water tight enclosure.

-No external apparatus to be connected to the

energizer power source (battery).

1 2 3 4 5 6

CONNECTOR BLOCK

BATTERY

ENERGIZER

PROGRAM

1 2 3 4

Remote Control

Pc Board

4 Ln2 (green)

3 Ln1 (white)

2 + 12V (red)

1 Gnd (black)

HV 1

HV 2

GND

MONITOR

HT XFMR

CT UNIT

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 9of 20

The BS120/BS102 control unit has the following features:

1 Can communicate with up to 13 BS120/BS102 units

2 Will automatically synchronize the HT pulse delivery of multiple energizer

units.

3 Can be configured for master or slave mode.

4 RS485 communication protocol.

5 Built-in time and date generator.

6 99 events memory. Data can be retrieved via LCD screen.

7 Pin protected user menu and -installer menu.

8 All energizer settings can be addressed via the keypad.

9 The BS120/BS102SMS control unit features an optional built-in modem

with full SMSout capability.

1 Fault Messages

Normal Display

Normal indication with a properly working fence.

It indicates that the unit’s address is nr. 1, it has been programmed for 20 zones, the fence

voltage is in the high (H)mode and the system is working properly.

The time and date indication is used for the event memory.

2007/01/01 0:00:17

UNIT1 H 20 ZONES

System OK

(RESET) (MENU)

STINGER ELECTRONICS (PTY) LTD BS120 INSTRUCTION MANUAL REF:03/2018

Printed: 4/26/2019 Page 10 of 20

THE FOLLOWING FAULTS CAN BE DISPLAYED:

The system is in the HIGH voltage mode and has detected that the live wire has been cut,

resulting in an open circuit indication. Pressing “reset” will silence the built-in buzzer, but the

problem needs to be resolved first before the screen will return to normal.

The system is in the LOW voltage mode and has detected that the live wire has been cut,

resulting in an open circuit indication. Pressing “reset” will silence the built-in buzzer, but the

problem needs to be resolved first before the screen will return to normal.

The systemis in the HIGH voltage mode and has detected that the livewire is touching a ground

wire in zone 2, resulting in a short circuit indication. Pressing “reset” will silence the built-in

buzzer, but the problem needs to be resolved first before the screen will return to normal.

The systemis in the LOW voltage mode and has detected that thelivewire is touching a ground

wire in zone 2, resulting in a short circuit indication. Pressing “reset” will silence the built-in

buzzer, but the problem needs to be resolved first before the screen will return to normal.

The system has detected that it is not possible to communicate with unit 1. Pressing “reset” will

silence the built-in buzzer, but the problem needs to be resolved first before the screen will

return to normal.

Mains Failure detection for unit 1. Theenergizer is now running from the battery for a limited

period of time.

2007/01/01 0:00:17

UNIT1 H 20 ZONES

! Open Circuit !

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 L 20 ZONES

! Open Circuit !

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 H ZONE 2

!Short Circuit !

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 L Zone 2

! Short Circuit !

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 !!!

No communication

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 H 20 Zones

! Mains Failure !

(RESET) (MENU)

2007/01/01 0:00:17

UNIT1 H 20 Zones

! BatteryLow !

(RESET) (MENU)

Inhaltsverzeichnis

Andere Stinger Stromversorgung Handbücher

Stinger

Stinger MC2 POWER SYSTEMS Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung