Stoane Lighting Iris Type S Bedienungsanleitung
Stoane Lighting Ltd
20 Dryden Road Bilston Glen Ind Est.
Loanhead Midlothian EH20 9LZ UK
T: +44 (0) 131 440 1313
F: +44 (0) 131 440 0049
www.stoanelighting.com
VAT No GB682885284
Limited Company 188910
Iris Type S
Installation and Maintenance
Instructions
IMPORTANT: All wiring connections must be made before switching on mains power.
European Conformity
Please retain these instructions for future reference
This product should not be disposed of in your general waste IP65 Dust tight and protected against low power jets of water.
Class III - Extra Low Voltage
SL Type S 2.85VF1.4W @ 500mA
All of our in-house printed paper
is 100% recycled and recyclable
Iris S.pdf 1 19/01/2021 14:37:21
Electrical Supply
Installation must be carried out by a qualified electrician in
accordance with BS 7671:2008 Wiring Regulations.
230/240V AC 50/60Hz mains supply to a suitable SELV
LED Driver.
Site conditions: LED equipment is more susceptible to
static damage and over voltage than previous technology.
Before handling or connecting to the mains supply ensure
that all Stoane Lighting (SL) products are protected from
static discharge and that the mains supply is to regulation.
(230V +10 -6%)
Mains cables must be double insulated, strain relieved
and separated from E.L.V output cables.
This unit requires a constant current driver. 500mA Max.
Observe polarity:
Positive (+) is marked as RED.
Incorrect supply or reverse polarity can cause irreparable
damage.
All connections must be made before switching on mains.
If the supply is energised prior to making the connections
to the fitting then the resulting surge will damage the LED.
Multiple LEDs should be wired in series, refer to driver
instructions for minimum/maximum load.
The entire dimming control circuit source must be of SELV
insulation class.
Maintenance:
All lighting equipment is delicate and easily damaged
through misuse or inappropriate installation (mechanical
or electrical). Repairs and replacements may cause
delays and will be chargeable. Contact SL for support if
required.
All Stoane Lighting products are covered by a five year
Warranty and a 25 year Duty of Care. Products are
designed to be upgraded, adapted and refreshed using
our comprehensive ReNew service. For more information
on our ReNew service and for full Warranty terms and
conditions visit stoanelighting.com or contact us at the
address shown.
The IP rating stated is applicable only when the fitting has
been installed as per these instructions.
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
Installation
Check that the mounting surface is suitable for the
installation of this fitting.
A 33mm diameter cutout is required.
Step 1 Make mains connections to SELV LED driver
and extra low voltage connections to the
fitting.
Step 2 Retaining Wings: Hold in the springs and
push into the cutout. Once released the
springs will hold the fitting in place.
OR
Retaining Ring: Insert fitting into cutout and
secure by screwing the retaining ring onto the
rear of the fitting.
Ensure supply driver and connectors are housed
indoors OR in a suitably IP rated enclosure. Cable
ends must be suitably waterproofed. Inspect supply
cables before installation to ensure there is no
damage which will allow water to enter the fitting.
After opening the sealed portion of the luminaire for
any reason, SL recommends running the fitting for 15
minutes with the lid open to expel moisture before
closing it up. This will prevent condensation on the
lens and protect the fitting from corrosion.
Ensure that the installation of this fitting does not
compromise any fire barrier offered by your ceiling.
Intumescent downlighter fire hoods should be used to
maintain the integrity of the barrier in the event of a
fire.
Do not cover the luminaire with insulation. Heat sinks
and fan assisted lamps must be kept free from dust
and well ventilated to ensure long term reliability and
light quality.
WARNING: Do not look at exposed LED lamps in
operation. Eye injury can result.
Cleaning:
Fully isolate the fitting and allow to cool.
Clean the fitting with a slightly damp lint free cloth
from a mild solution of soap and water. The fitting
must be completely dry before reconnecting power.
Incompatible or abrasive chemicals can damage the
fitting, contact SL for advice if required.
Iris S.pdf 2 19/01/2021 14:37:21
12
or
Retaining
Wings
OUTPUT 2
Connect to Mains
Connect to
fittings
33mm cut out
Min 4mm
Max 17mm
Min 1mm
Max 9mm
Iris S.pdf 3 19/01/2021 14:37:21
1
2
LENS / SNOOT CHANGE
Fully isolate and allow fitting to cool sufficiently before
handling.
Step 1 Lock the fitting at a non-tilted position and use
the specialist tool provided to unwind the ring
anti-clockwise to remove it from the tube.
Step 2 The lens and or snoot can now be removed
from the fitting and replaced with one of suitable
specification.
Ensure the O-ring sits neatly, is not twisted, stretched or
deformed in any way and sits neatly in its groove. It must
be free from debris of any kind. If needed, remove the
O-ring, clean it and the groove and replace with fresh
grease (Loctite Superlube). Failure to do so may result in
water ingress and premature failure of the luminaire
Reverse process to re-assemble.
1.5mm Allen Key
Tilt Adjustment
To adjust, loosen the M2 fixings with the supplied
1.5mm Allen key. A single turn should be sufficient to
unlock, do not remove the fixings.
Once adjustment is complete, tighten the fixings to
lock in place.
Optic
Bezel
Optic
Holder
Optic
spacer
Tool
Iris S.pdf 4 19/01/2021 14:37:21
Stoane Lighting firmly believe that we have a responsibility as environmental
custodians, we believe that lighting equipment should be built to last, to be
repaired and to be reused. As a BCorp we believe that we must look to operate in
a business not aiming to just be best in the world but a business best for the world.
Stoane Lighting believe that the circular economy is a fundamental aspect of how
we approach the challenges we face. If you read this at the end of the product life
we encourage you to consider how you can ensure these products see an
extended life.
All Stoane Lighting products are supplied with a 5 year warranty and a 25 year
duty of care.
Stoane Lighting operate a ReNew division, which can take your existing fittings
and refurbish or upgrade without the need for replacing what you already have.
Through the ReNew service, Stoane Lighting provides general repair, deep cleans
and electrical safety checks on luminaires, as well as possible repainting if needed.
We will replace components that are nearing end of life, such as drivers, LEDs,
and optics. If the fittings are to be used in a new area, or the existing space is
undergoing a change in use, ReNew can offer a different mounting method or light
technical performance (such as colour tuning), if needed, alongside the addition of
on-board wireless control.
Once fittings have been repaired or upgraded through ReNew, they will start a new
five-year warrantly period, and any unwanted parts will be recycled.
For more information the Warranty, Duty of Care or ReNew service please visit stoanelighting.com
or contact us at the address shown.
Iris S.pdf 5 19/01/2021 14:37:21
Inhaltsverzeichnis
Andere Stoane Lighting Leuchte Handbücher
Beliebte Leuchte Handbücher anderer Marken
Emos
Emos CLASSIC ZY1431T Bedienungsanleitung
Westinghouse
Westinghouse Outdoor Lighting Fixture Bedienungsanleitung
Hedler
Hedler C 12 silent Bedienungsanleitung
Blizzard Lighting
Blizzard Lighting Puck: CSI Bedienungsanleitung
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Bedienungsanleitung
Lightmaxx
Lightmaxx Shaft 5R Bedienungsanleitung
Cooper Lighting
Cooper Lighting Halo L3232E Bedienungsanleitung
Stageline
Stageline ODW-2410RGBW Bedienungsanleitung
Light Sky
Light Sky Tornado Series Bedienungsanleitung
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung
Lightolier
Lightolier Lytespan 83ED17S Bedienungsanleitung
Lightolier
Lightolier Calculite CS8226 Bedienungsanleitung