Streamline SFC05-09 Bedienungsanleitung

INSTRUCTION

MANUAL

STREAMLINE

SFC05 - 09

SFC16

Codes:

INSTR-SFC

2W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 3

• STREAMLINE® systems can be built according to customers’ exact requirements

• For non-standard systems, the user’s needs or speciﬁcations are listened to and turned

into reality.

• Whilst price is important, quality is remembered long after price is forgotten

• We insist on sourcing brand name products from around the world, only of a reputable

quality, and bring them together under the STREAMLINE® name

• All STREAMLINE® products carry a full one year’s warranty, according to the manufacturers’

standard terms and conditions of sale.

• We have an in-house technical helpline able to answer most of your questions relating to the

capabilities and functionalities of all STREAMLINE® products

• If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately

attend to sending you the correct item and arrange a collection of the wrong item without

any quibbles

• STREAMLINE® is backed by a comprehensive range with massive stocks providing you with a

‘one stop shop’ for all your requirements.

Flexibility

Quality

Service

Why STREAMLINE®?

MANUFACTURED

IN THE

UNITED KINGDOM

CHECKED AND

TESTED BY

QUALITY CONTROL

Contents

1. Why STREAMLINE®?

2. STREAMLINE® Warranty

4. Operating Warnings

5. Set Up Auto Calibrate

6. Operation

3. Wiring

1Why STREAMLINE®

Controller Messages

7 - 8

STREAMLINE

4W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 5

V16

STREAMLINE® Warranty Wiring

The warranty on all Machines and Equipment is

for 1 year (12-months) from RECORDED DATE

OF PURCHASE.

THIS WARRANTY EXCLUDES NORMAL

MAINTENANCE ITEMS, including but not limited

to HOSES, FILTERS, O-RINGS,

DIAPHRAGMS, VALVES, GASKETS,

CARBON BRUSHES and damage to motors

and other components as a result of failure to

replace normal maintenance items. THIS LIST

IS NOT EXHAUSTIVE.

If STREAMLINE® receives notice of such defects

during the warranty period, STREAMLINE®

will either, at its opinion, repair or replace

components which prove to be defective.

Replacement parts will only be supplied under

warranty, upon the inspection and approval of

the defective parts by STREAMLINE®.

Should it be necessary to supply replacement

parts before the opportunity to inspect, these

will be charged at current prices and credit will

only be issued upon subsequent inspection and

warranty approval by STREAMLINE®.

The customer is responsible for the cost of

return of the defective part. If warranty is

approved, STREAMLINE® will pay for the cost

of the repaired or replacement part.

This warranty excludes the following conditions

and circumstances which are at the discretion

of STREAMLINE®:

Wear and tear, misuse, abuse improper

maintenance, frost damage, the use of chemicals

other than those supplied or approved by

STREAMLINE®, improper installation or repair,

unauthorised modiﬁcation, incidental or

consequential costs, loss or damage, service,

labour or third party charges, the cost of

returning defective parts to STREAMLINE®.

This warranty constitutes the exclusive remedy

of any purchaser of a STREAMLINE® unit and

is in lieu of all other warranties, express or

implied, including without limitation any implied

warranty of merchantability or ﬁtness for use, to

the fullest extent permitted by law. In no event

shall any implied warranty of merchantability or

ﬁtness for use exceed the term of the applicable

warranty stated above and STREAMLINE® shall

have no other obligation or liability.

Important

Unfortunately these rights cannot be

transferred to a third party.

2STREAMLINE®Warranty

Important

The Fuse for this unit is a 10A Fuse. Make sure correct fuse is ﬁtted in-line, close

to the battery end of the RED (positive) wire. Failure to do so will result in

damage to the unit.

Connect the pump controller in accordance with this diagram.

NOTE: only ﬁt the fuse once all connections are made

3Wiring

Enter Button

Down / Up Buttons

Fuse 10A

12V Battery Pump

Power Button

Display

STREAMLINE

6W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 7

4Operating Warnings

Operating Warnings Set Up Auto Calibrate

Important

Your battery is at risk of permanent damage if you disable low battery cut-o

and continue to use your controller for long periods when the battery voltage

has fallen below +10.5V.

Adjust the ﬂow settings carefully. Repeated false dead-end detection indicates that the Cal value

should be increased (less sensitive).

For safety wire through the pump pressure switch. (The pressure switch can be bypassed if

absolutely necessary - the unit will protect itself under normal conditions.)

This is a WATER PUMP controller: it will not work with air in the system. Always prime the system

before starting work. If air in the system causes false dead-end detection, increase Cal value until air

is removed.

Do not set the Cal value too high. Setting it higher than necessary places extra strain on both the

pump and the controller in a dead end situation. This can result in damage to both the pump and

your controller.

Speciﬁcation Value

Supply Voltage 11 - 15 VDC

Maximum Current 15A

Typical Drive Current 8A

Voltmeter Accuracy + - 100mV

Enclosure Material ABS

Water Resistance IP65

Dimensions 115 x 65 x 40 (mm)

Working Temperature 0 - 40 Deg C

5Set Up Auto Calibrate

Connect your hose and pole + brush to the pump.

Turn on the controller by pressing the power button.

Press and hold the up and enter buttons to

calibrate. CAL will be displayed.

To select Auto Cal continue to press the down

button until AUt is displayed. Press the enter

button to start. Auto Cal starts from C99.

After several moments the calculated CAL value

(e.g. C50) will be displayed and the controller is

ready to use. Press enter to exit calibration.

Press up until the display shows 30.

DisplayButton

STREAMLINE

8W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 9

DisplayButton

The CAL value can be adjusted manually by

following the same steps and adjusting the CAL

value by pressing the up or down button instead

of using AUt.

To enable or disable the low battery cut-o*

(that stops your pump when the battery voltage

is below 10.5V) press and hold the down and

enter buttons.

Then use the up or down button to select ON or OFF. Press enter to save.

NOTE: ‘ON’ keeps your battery protected.

6Operation

To select Auto Cal continue to press the down

button until AUt is displayed. Press the enter

button to start. Auto Cal starts from C99.

DisplayButton

Press enter to display the current

battery voltage.

Press enter again to return to the current ﬂow rate.

To turn the controller o, press the power button.

Operation

STREAMLINE

10 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 W: www.streamline.systems E: sales@streamline.systems T: +44 (0)1626 830 830 11

An error has occurred while using AutoCal. This will

happen when the motor is not connected or the enter

button has been pressed to cancel it.

Pressure switch activated or pump disconnected