StrongLink SL030 Bedienungsanleitung

RFID MODULE

Mifare Read/Write Module

SL030

User Manual

Version 1.3

Dec 2006

StrongLink

StrongLink SL030

CONTENT

1. MAIN FEATURES.................................................................................. 3

2. PINNING INFORMATION................................................................... 4

3. DEVICE OPERATION.......................................................................... 5

3-1. CLOCK and DATA TRANSITIONS:.................................................................... 5

3-2. START CONDITION .............................................................................................. 5

3-3. STOP CONDITION................................................................................................. 5

3-4. ACKNOWLEDGE ................................................................................................... 5

3-5. BUSY STATE ........................................................................................................... 6

3-6. Device Addressing..................................................................................................... 6

3-7. Write Operations...................................................................................................... 6

3-8. Read Operations....................................................................................................... 7

4. COMMAND DESCRIPTION ............................................................... 7

4-1. Format ...................................................................................................................... 7

4-2. Command Overview................................................................................................ 8

4-3. Command List.......................................................................................................... 9

4-3-1. Select Mifare card ................................................................................................ 9

4-3-2. Login to a sector ................................................................................................... 9

4-3-3. Read a data block................................................................................................. 9

4-3-4. Write a data block.............................................................................................. 10

4-3-5. Read a value block.............................................................................................. 10

4-3-6. Write a value block ............................................................................................ 10

4-3-7. Write master key (KeyA)................................................................................... 11

4-3-8. Increment value.................................................................................................. 11

4-3-9. Decrement value................................................................................................. 11

4-3-10. Copy value........................................................................................................... 12

4-3-11. Read a data page (Mifare_UltraLight)............................................................. 12

4-3-12. Write a data Page (Mifare_UltraLight)........................................................... 12

4-3-13. Power Down........................................................................................................ 12

http://www.stronglink.cn 2

StrongLink SL030

1. MAIN FEATURES

•Tag supported: Mifare 1K, Mifare 4K, Mifare UltraLight

•Auto detecting tag

•Built-in antenna

•0 to 400 kHz bit-wide I2C-bus communication

•DC2.5V to DC3.6V VDD operating, I/O pins are 5V tolerant

•Work current less then 40mA @3.3V

•Power down current less then 10uA

•Operating distance: Up to 50mm, depending on tag

•Storage temperature: -40 ºC ~ +85 ºC

•Operating temperature: -25 ºC ~ +70 ºC

•Dimension: 38 × 38 × 3 mm

•The OUT pin is low level indicating tag in, and high level indicating tag

out

http://www.stronglink.cn 3

StrongLink SL030

2. PINNING INFORMATION

PIN SYMBOL TYPE DESCRIPTION

1 VDD PWR Power supply, DC2.5V to DC3.6V

2 IN Input Falling edge wake up SL030 from power down mode

3 SDA Input/Output Serial Data Line

4 SLC Input Serial Clock Line

5 Out Output Tag detect signal

low level indicating tag in

high level indicating tag out

6 GND PWR Ground

7 NC

8 NC

9 NC

10 NC

http://www.stronglink.cn 4

StrongLink SL030

3. DEVICE OPERATION

3-1. CLOCK AND DATA TRANSITIONS:

The SDA pin is normally pulled high with an external device. Data on the SDA pin may

change only during SCL low time periods. Data changes during SCL high periods will

indicate a start or stop condition as defined below.

3-2. START CONDITION

A high-to-low transition of SDA with SCL high is a start condition which must precede any

other command

3-3. STOP CONDITION

A low-to-high transition of SDA with SCL high is a stop condition.

3-4. ACKNOWLEDGE

All addresses and data words are serially transmitted to and from the SL030 in 8-bit words.

The SL030 sends a zero to acknowledge that it is not busy,and has received each word.

This happens during the ninth clock cycle.

http://www.stronglink.cn 5

StrongLink SL030

3-5. BUSY STATE

When the SL030 has received command, then don’t acknowledge IIC bus until ends with

the card communication.

3-6. Device Addressing

The SL030 devices require an 8-bit device address word following a start condition to

enable the chip for a read or write operation.

The device address word consists of 7 bits addressing and 1 bit operation select bit.

The first 7 bits are the SL030 addressing, is 1010000

The eighth bit of the device address is the read/write operation select bit. A read operation

is initiated if this bit is high and a write operation is initiated if this bit is low.

3-7. Write Operations

The host device send a command(refer chapter 4) to SL030 via write operation, then SL030

will carry out the order that receive. Finished time according to different order

http://www.stronglink.cn 6

StrongLink SL030

3-8. Read Operations

The host device passes to read the operation gets the order carries out the result

4. COMMAND DESCRIPTION

4-1. FORMAT

Host Write Command to SL030:

Address Len Command Data

Address: 1 byte, 0xA0

Len: Byte length counting from Command Code to the last byte of the data,

1 byte.

Command: Command Code, 1 byte.

Data: Data, variable length depends on the command type.

Host Read The Result:

Address Len Command Status Data

Address: 1 byte, 0xA1

Len: Byte length counting from Command Code to the last byte of the data,

1 byte.

Command: Command Code, 1 byte

Status: Command status, 1 byte

Data: Data, variable length depends on the command type.

http://www.stronglink.cn 7

StrongLink SL030

4-2. COMMAND OVERVIEW

Command Description

0x01 Select Mifare card

0x02 Login to a sector

0x03 Read a data block

0x04 Write a data block

0x05 Read a value block

0x06 Write a value block

0x07 Write master key (key A)

0x08 Increment value

0x09 Decrement value

0x0A Copy value

0x10 Read a data page (ultra_light)

0x11 Write a data page (ultra_light)

0x50 Go to Power Down mode

STATUS OVERVIEW

Status Description

0x00 Operation success

0x01 No tag

0x02 Login success

0x03 Login fail

0x04 Read fail

0x05 Write fail

0x06 Unable to read after write

0x0A Collision occur

0x0C Load key fail

0x0D Not authenticate

0x0E Not a value block

http://www.stronglink.cn 8

StrongLink SL030

4-3. COMMAND LIST

4-3-1. Select Mifare card

Host Write:

Len 0x01

Host Read:

Len 0x01 Status Serial num Type

Status: 0x00: Operation success

0x01: No tag

0x0A: Collision occur

Serial num: Serial number of the card detected if the operation is success, 4 bytes for

Mifare Standard & Mifare ProX, 7 bytes for Mifare UltraLight & Mifare DesFire

Type: 0x01: Mifare Standard 1K card

0x02: Mifare Pro card

0x03: Mifare UltraLight card

0x04: Mifare Standard 4K card

0x05: Mifare ProX card

0x06: Mifare DesFire card

4-3-2. Login to a sector

Host Write:

Len 0x02 Sector Type Key

Sector: Sector need to login

Type: Key type (0xAA: authenticate with KeyA, 0xBB: authenticate with KeyB)

Key: Authenticate key, 6 bytes

Host Read:

Len 0x02 Status

Status: 0x02: Login success

0x01: No tag

0x03: Login fail

0x0C: Load key fail

4-3-3. Read a data block

Host Write:

Len 0x03 Block

Block: The block number to be read, 1 byte

Host Read:

Len 0x03 Status Data

Status: 0x00: Operation success

0x04: Read fail

0x0D: Not authenticate

0x01: No tag

Data: Block data returned if operation is success, 16 bytes.

http://www.stronglink.cn 9

StrongLink SL030

4-3-4. Write a data block

Host Write:

Len 0x04 Block Data

Block: The block number to be written, 1 byte.

Data: The data to write, 16 bytes.

Host Read:

Len 0x04 Status Data

Status: 0x00: Operation success

0x01: No tag

0x05: Write fail

0x06: Unable to read after write

0x07: Read after write error

0x0D: Not authenticate

Data: Block data written if operation is success, 16 bytes.

4-3-5. Read a value block

Host Write:

Len 0x05 Block

Block: The block number to be read, 1 byte.

Host Read:

Len 0x05 Status Value

Status: 0x00: Operation success

0x01: No tag

0x04: Read fail

0x0D: Not authenticate

0x0E: Not a value block

Value: Value returned if the operation is success, 4 bytes.

4-3-6. Write a value block

Host Write:

Len 0x06 Block Value

Block: The block number to be written, 1 byte.

Value: The value to write, 4 bytes.

Host Read:

Len 0x06 Status Value

Status: 0x00: Operation success

0x01: No tag

0x05: Write fail

0x06: Unable to read after write

0x07: Read after write error

0x0D: Not authenticate

Value: Value written if the operation is success, 4 bytes.

http://www.stronglink.cn 10

Andere Handbücher für SL030

Inhaltsverzeichnis

Andere StrongLink Steuereinheit Handbücher

StrongLink

StrongLink SL032 Bedienungsanleitung

StrongLink

StrongLink SL030 Bedienungsanleitung

StrongLink

StrongLink SL025B Bedienungsanleitung

StrongLink

StrongLink RT400 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung