Stryker 0240-031-000 Bedienungsanleitung
VisionPro 26” LED Display
VisionPro 26”LED Display: 0240-031-020
SYNK VisionPro 26”Wireless LED Display: 0240-031-000
Table of Contents
Warnings and Cautions ............................................................................................1
About Your Device.....................................................................................................3
Intended Use ........................................................................................................................3
Indications.............................................................................................................................4
Contraindications................................................................................................................4
Package Contents ...............................................................................................................4
Device Features....................................................................................................................5
Setup............................................................................................................................9
Connections..........................................................................................................................9
Basic Video Setup.............................................................................................................11
Operation................................................................................................................. 12
On-Screen Display (OSD)............................................................................................... 12
OSD Menus......................................................................................................................... 13
Troubleshooting............................................................................................................... 15
Cleaning and Maintenance................................................................................... 17
Disposal ...............................................................................................................................17
Technical Specications ........................................................................................ 18
Display..................................................................................................................................18
Symbols.................................................................................................................... 23
1
Warnings and Cautions
Please read this manual and follow its instructions carefully. The words warning, caution,
and note carry special meanings and should be carefully reviewed:
Warning: Indicates measures to avoid potential serious injury to the user and the patient
and/or damage to this device.
Caution: Indicates risks to the equipment. Failure to follow cautions may result in product
damage.
Note: Provides special information to clarify instructions or present additional useful
information.
Warnings
To avoid potential serious injury to the user and the patient and/or damage to this device, please
note the following warnings:
1. Read this manual thoroughly and be familiar with its contents prior to using this device.
2. Federal law (United States of America) restricts this device to sale by, or on the order of, a
physician.
3. Carefully unpack the device and check if any damage occurred during shipment.
4. This device is non-sterile and therefore should not be placed in the sterile eld.
5. Do not place the device or any other heavy object on the power cord. Damage to the cable
can cause re or electric shock.
6. To avoid electric shock, avoid removing the bezel.
7. This device should not be used adjacent to or stacked with other devices. If adjacent or
stacked use is necessary, the device should be observed to verify normal operation in the
conguration in which it will be used.
8. Test this device prior to a surgical procedure. This device was fully tested at the factory
before shipment.
9. Do not attempt internal repairs or adjustments not specically detailed in this manual.
Ensure that readjustments, modications, and/or repairs are carried out by persons
authorized by Stryker Endoscopy.
10. Do not put any liquid or solid object into the panel. If this occurs, unplug the device and
have it checked by qualied personnel before operating it any further.
11. Use appropriate caution to prevent contact with uids if the device is being used with a
power supply in patient environments.
12. The use of cables and/or other accessories with this device, other than those specied, may
result in increased emissions or decreased immunity of this device.
Cautions
1. Connect the device to an AC adapter connected to a hospital grade power cord ensuring the
power cord is plugged into a grounded power outlet to achieve grounding reliability.
2. Do not sterilize the device, as the delicate electronics cannot withstand this procedure.
2
3. Use only the proprietary surgical display power supply for the display. Completely secure the
connection between the DC power cord and the extension cord.
4. Never operate the device immediately after transportation from a cold location to a warm
location.
5. To connect to an international power supply, use an attachment plug appropriate for the
cations" section of this manual.
6. Unplug the device if it is not to be used for an extended period of time. To disconnect the
rst, then pull the cord out by the plug. Never pull the cord itself.
7. Do not expose the device to moisture or apply liquid cleaners directly to the screen. Spray
the cleaning solution into a soft cloth and clean gently. For further detail, refer to the
"Periodic Maintenance" section of this manual.
8. Allow adequate air circulation to prevent internal heat buildup. Do not place the device
on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the
ventilation slots. The device is cooled by natural convection and has no fan.
9. Do not touch the patient with signal input or output connectors. Equipment with SIP/
national standards or the combination should be evaluated for safety.
10. To ensure electromagnetic compatibility, refer to the“Electromagnetic Compatibility” section
11. Pay close attention to the cleaning instructions in this manual. A deviation may cause
damage.
12. Do not install the device near sunlight, excessive dust, mechanical vibration, or shock.
13. Do not operate with the glass device screen facing downward.
14. Handle the device with care. Do not strike or scratch the screen.
cations not expressly approved by the party responsible for compliance
could void the user’s authority to operate the device.
16. Note : This device has been tested
and
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices,
a separation distance of 20cm or more should be maintained between the antenna of this
device and persons during operation. To ensure compliance, operation at closer than this
distance is not recommended. The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
found to comply with the limit for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation, which can be determined by
and on. The user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving device.
• Increase the separation distance between the device.
• erent from that to which the other
device(s) are connected.
• eld service technician for help.
of this manual. The device must be installed and operated according to the EMC information
provided in this manual.
3
About Your Device
VisionPro 26” LED Display
REF: 0240-031-020
The VisionPro 26”LED Display is a wide screen LED surgical display that can support a maximum
resolution of WUXGA (1920x1200). The display supports various video inputs, including digital
RGB, analog RGB, serial digital interface (SDI), component video (YPbPr/RGB), S-video, and
C-video, and wireless RGB.
SYNK VisionPro 26”Wireless LED Display
REF: 0240-031-000
The SYNK VisionPro 26”Wireless LED Display can be used with the optional SYNK Transmitter,
which allows it to receive a high-denition video signal over a radio-frequency link. The wireless
display supports a wireless RGB video input in addition to the video inputs supported by the
VisionPro 26” LED Display.
For details and instructions on using the SYNK Transmitter and the wireless functionality of the
SYNK VisionPro 26”Wireless LED Display, refer to the SYNK Wireless System manual (P21693)
Intended Use
The SYNK VisionPro 26”Wireless LED Display and the VisionPro 26” LED Display are intended for
video display during surgical procedures.
4
Indications
This device is indicated for the following surgical procedures:
• Arthroscopy (orthopedic surgery)
• Laparoscopy (general and gynecological surgery)
• Thorascopy
• Endoscopy (general, gastroenterological and ENT)
• ENT
• Gynecology
• General surgery
The display is a non-sterile, reusable device not intended for use in the sterile eld. The display
is intended for use by qualied physicians having complete knowledge of these surgical
procedures.
Contraindications
There are no known contraindications for this device.
Package Contents
1
2
3
4
5
Package Contents Part Number
1. VisionPro 26” LED Display or SYNK VisionPro 26”
Wireless LED Display
0240-031-020 ,0240-031-000
2. (4) M4 × 10 mm VESA screws –
5
3. Hospital-grade AC power cord –
4. VisionPro 26” Series Power Supply 0240-031-004
5. Cable Cover –
Optional Accessories Part Number
SYNK Wireless Transmitter 0240-031-010
SYNK Wireless Receiver 0240-031-030
SYNK Display Media Bar 0240-031-003
SYNK 26”Display Cover 0240-031-002
Hospital-grade AC power cord ??
15-ft. (5 pin) DC extension cable ??
75-ft. (5 pin) DC extension cable ??
Device Features
Front panel
Operate the display using the rotary control located on the front panel. A list of the display
controls and their functions is provided below.
1
2
34 5 6 9
8
7 10
1. Display Screen Shows video image.
2. Power switch (soft) Powers the display ON and OFF.
3. Power LED Indicates current status. Shines green if the display is
powered on or is in screen saver mode; blinks red if the
display is in standby mode; blinks amber if over voltage.
6
4. Token slot (SYNK
VisionPro 26”Wireless
LED Display only)
Token insertion site used to establish a wireless connection
with the transmitter.
5. Token LED SYNK
VisionPro 26”Wireless
LED Display only)
Provides feedback when linking the display and
transmitter.
6. Audio/PIP VisionPro 26” LED Display:
Press once for the Picture in Picture adjustment menu.
SYNK VisionPro 26”Wireless LED Display:
Press once for the Audio adjustment menu (if optional
Media Bar is installed).
Press twice for Picture in Picture adjustment menu.
7. Bright Accesses the Brightness adjustment menu
8. Specialty Accesses the Specialty adjustment menu
9. Input Accesses the Input adjustment menu
10. Rotary control Accesses the on-screen display and navigates through its
functions.
Rear panel
1
3
4
2
7
5
8
6
1. VESA mounting holes
(100mm)
Provide access points for mounting the display.
2. Power switch (hard) Powers the input DC power ON and OFF.
3. Power connector Connects to the 24V DC power supply.
7
4. Handles Aid in display positioning.
Note: The handles are not intended to bear the
entire weight of the display
5. Cable-management cover Covers cables.
Cable Cover
Installing the Cable Cover
1. Align the left and right hinges of the cable cover onto the bottom rear of the display.
2. Snap on the top section of the cable cover to the aligning clips.
3. With your ngers, turn the thumbscrews clockwise to tighten and lock the cable cover
onto the display.
Removing the Cable Cover
1. With your ngers, turn the thumbscrews counterclockwise to loosen.
2. Once the thumbscrews are completely loosened, pinch the left and right clips and pull the
cable cover towards you.
3. Remove the cable cover from the left and right hinges.
8
Display Handles
Note: The handles are intended to aid in positioning the display, not for transporting the
display. The handles should not bear the full weight of the display.
Removing or Reinstalling the Display Handles
To Remove:
1. Using a Philips screwdriver, loosen the two **(insert size)** screws and gently pull the
handle away from the display.
To Reinstall:
1. Align the handle with the screw holes on the rear of the display.
2. Using a Philips screwdriver, install the two **(insert size)** screws to attach the handle.
3. To remove the handles, loosen the screws with a Philips screwdriver and gently pull the
handle away from the display.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Stryker Monitor Handbücher
Stryker
Stryker 0240-030-960 Bedienungsanleitung
Stryker
Stryker WiSe 26 inch HDTV Bedienungsanleitung
Stryker
Stryker visionpro 0240-031-020 Bedienungsanleitung
Stryker
Stryker 240-030-960 Bedienungsanleitung
Stryker
Stryker 0240-031-050 Bedienungsanleitung
Stryker
Stryker 240-031-050 Bedienungsanleitung
Stryker
Stryker VisionElect 240-030-930 Bedienungsanleitung
Stryker
Stryker VisionPro EDAM Bedienungsanleitung
Stryker
Stryker VisionPro Bedienungsanleitung
