Strymon MultiSwitch Plus Bedienungsanleitung
USER MANUAL
MultiSwitch Plus - Extended Control
pg 2
Table of Contents
OVERVIEW
PRESET MODE
CUSTOM MODE
TIMELINE, BIGSKY & MOBIUS MODE
TAP, FAV, BOOST & SPEED MODE
COMBO MODE
APPENDIX
PRESET MODE PEDAL SETUP
TIMELINE, BIGSKY & MOBIUS MODE SETUP
TAP, FAV, BOOST & SPEED MODE PEDAL SETUP
COMPATIBILITY CHART
SPECIFICATIONS
WARRANTY
3
4
5
6
7
8
10
11
13
15
16
17
MultiSwitch Plus - Extended Control
pg 3
Overview
FOOTSWITCHES
The footswitches can be programmed to send
a variety of different commands to your pedals.
These footswitches are referred to as A, B, and C.
OUTPUT JACKS
The output jacks allow commands to be sent to your
pedals and provide power from these pedals. These
output jacks are referred to as • (one), •• (two), and
••• (three).
MultiSwitch Plus enhances your ability to control Strymon pedals at your feet
without the complexity of MIDI. MultiSwitch Plus has three LEDs, output jacks,
and footswitches.
MultiSwitch Plus - Extended Control
pg 4
Preset Mode
Release the footswitch. The LEDs on
MultiSwitch Plus will flash GREEN when
configuration is complete.
All outputs carry the same signal in this
mode.
Check the Appendix for instructions on
how to configure the connected pedal for
use in this mode.
Enter Preset Mode by holding down the A
footswitch while connecting the TRS cable to
MultiSwitch Plus. The ALED will flash RED
to confirm the selection.
Connect the included TRS cable to the EXP
jack of the pedal you wish to control.
3
4
2
1
This mode adds the ability to select and bypass three presets on supported pedals.1
Press a footswitch with an unlit LED to select that preset on connected pedals. Step
on the same footswitch again to bypass the pedals.
1 Check the Compatibility Chart on pg.15 for details
and a list of compatible pedals. NOTE: These three presets correspond to MIDI
Program Change messages 1-2-3.
NOTE: For Volante, this is equivalent to the
presets stored on playback buttons 2-3-4. For
Sunset and Riverside, these are independent
of the preset that is associated with the FAV
footswitch, which is equivalent to MIDI PC# 0.
A
B C
+
EXP
MultiSwitch Plus - Extended Control
pg 5
Custom Mode
Release the footswitch. The LEDs on
MultiSwitch Plus will flash GREEN when
configuration is complete. All three
outputs carry the same signal in this mode.
Enter Custom Mode by holding down the C
footswitch while connecting the TRS cable to
MultiSwitch Plus. The CLED will flash RED
to confirm the selection.
Connect the included TRS cable to the EXP
jack of the pedal you wish to control.
3
2
1
This mode adds remote control functionality unique to the supported pedal.1
Check the manual for the connected
pedal for for specific functionality and
instructions on how to configure the pedal
for use in this mode.
4
A B
C
+
EXP
1 Check the Compatibility Chart on pg.15 for details
and a list of compatible pedals.
MultiSwitch Plus - Extended Control
pg 6
TimeLine, BigSky & Mobius Mode
Release the footswitches. The LEDs on
MultiSwitch Plus will flash GREEN when
configuration is complete.
All outputs carry the same signal in this mode.
Enter TimeLine, BigSky and Mobius Mode by
holding down the Band Cfootswitches at the
same time while connecting the TRS cable
to MultiSwitch Plus. The Band CLEDs will
flash RED to confirm the selection.
Connect the included TRS cable to the EXP
jack of the pedal you wish to control.
3
2
1
This mode adds expanded preset selection control for TimeLine, BigSky, and
Mobius and dedicated Looper controls for TimeLine.
May require firmware update. Check the Compatibility Chart on pg.15 for details.
NOTE: MultiSwitch Plus LEDs remain unlit in
this mode. The TimeLine, BigSky and Mobius
are not capable of bidirectional communication
which is required to support MultiSwitch Plus
LED functionality.
Check the Appendix for instructions on how
to configure the connected pedal for use in
this mode.
4
A
B
C
A B
C
+ +
EXP
MultiSwitch Plus - Extended Control
pg 7
This mode allows you to connect up to three supported pedals1for independent,
dedicated footswitch functions.
Tap, Favorite, Boost & Speed Mode
Release the footswitch. The LEDs on MultiSwitch
Plus will all be lit. Press the footswitches to
assign each switch and jack pair to control Tap
(GREEN LED) or FAV/Boost/Speed (RED LED).
Enter Tap, Favorite, Boost & Speed Mode by
holding down the Bfootswitch while connecting
the TRS cable to MultiSwitch Plus. The BLED
will flash RED to confirm the selection and all
LEDs will illuminate.
Connect the included TRS cable to the EXP or
FAV jack of the pedal you wish to control.
Press and hold the Bfootswitch to exit
configuration mode.
3
2
1
4
Tap, Boost,
Fav or Speed
Footswitch A
Output Signal
Footswitch B
Output Signal
Footswitch C
Output Signal
Check the Appendix for instructions on
how to configure the connected pedal for
use in this mode.
51 Check the Compatibility Chart on pg.15 for
details and a list of compatible pedals.
A
B
C
+
EXP
MultiSwitch Plus - Extended Control
pg 8
Footswitches A/ Band output jacks 1 / 2 match the behavior of Preset mode. Footswitch C
and output jack 3 match the behavior of TAP, FAV, BOOST & SPEED MODE.
Combo Mode
After entering Combo Mode the Cfootswitch
LED will indicate whether it is assigned to
control Tap (GREEN LED) or FAV/Boost/Speed
(RED LED). Press the Cfootswitch to toggle
between these two options.
Enter Combo Mode by holding down the Aand
Bfootswitches while connecting the TRS cable
to MultiSwitch Plus. The Aand BLEDs will flash
RED to confirm the selection.
Connect the included TRS cable from output 1
or 2 to the appropriate jack of one of the pedals
you wish to control.
Press and hold Bto exit configuration.
Connect an additional TRS cable from output 3
to the pedal receiving Tap, Boost, Fav or Speed
signal.
Check the Appendix for instructions on how to
configure the connected pedal for use in this
mode.
3
2
1
4
5
6
PRESET 1
PRESET Output Footswitch C
Output Signal
PRESET 2 Tap, Boost,
Fav or Speed
Check the Compatibility Chart on pg.15 for details
and a list of compatible pedals.
A
B C
A
B
C
+ +
EXP
MultiSwitch Plus - Extended Control
pg 9
Appendix
Connected Pedal Setup
MultiSwitch Plus - Extended Control
pg 10
A quick reference for the connected pedal setup. For more details see pedal user manual.
Preset Mode Pedal Setup
Press either footswitch to store the EXP jack
assignment.
Press either footswitch to store the EXP jack
assignment.
Turn the LEVEL knob until the ON LED turns
BLUE to set the EXP jack mode to MIDI Mode.
Turn the LEVEL knob on the B side until the B
LED turns BLUE to set the EXP jack mode to
MIDI Mode.
Press and hold the FAVORITE footswitch while
powering up the pedal.
Press and hold the A footswitch while
powering up the pedal.
3
3
2
2
1
1
Riverside
Setting EXP jack to MIDI mode.
Sunset
Setting EXP jack to MIDI mode.
Turn the ECHO LEVEL knob until the TAP
LED turns BLUE.
To configure the EXP jack, press and hold
the TAP button while powering up Volante.
2
1
Volante
Setting EXP jack to Preset mode.
Press the TAP footswitch to store this setting.
3
Inhaltsverzeichnis
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
