SubC Imaging Rayfin Bedienungsanleitung
Support Engineered in Canada
TW: ADR
PM: CC
+1 (709) 702-0395 [email protected] SubC Control Ltd
327 Memorial Drive
Clarenville, NL, Canada, A5A 1R8
www.subcimaging.com
Installing TeamViewer for remote support
1. Ensure the LAN functionality in TeamViewer is enabled (go to Extras > Options > General > Incoming LAN
connections). Using TeamViewer over LAN allows for much faster operation and better quality. SubC
recommends using a LAN connection whenever possible.
2. You can obtain TeamViewer 8 software from:
https://community.teamviewer.com/t5/Knowledge-Base/Download-TeamViewer-8-and-9/ta-p/78348
Install and open Teamviewer on your computer. You will see a window similar to the one below.
3. Make note of the Your ID and Password fields.
4. Contact [email protected]om and provide them with your codes; they now have remote access
and can help with any issues that may arise.
Installing AnyDesk for remote support
1. Download Anydesk from https://anydesk.com/. Once downloaded, open the
AnyDesk.exe file.
2. Once the program is running, you will see a window similar to the one to the right.
Make note of your address.
3. Click the settings button and choose the option to Set Password from the list.
4. A new window will appear, check the option “Enable unattended access”.
5. Type in a password twice and click the Apply button.
6. Contact [email protected]om and provide them with your address and
password; they now have remote access and can help with issues that may arise.
2
3
Please read this manual carefully before setting up and using your unit. The electronic version of this document is the controlled copy. Therefore,
all printed versions of this document are uncontrolled.
1. SubC equipment is designed to work at various depth ratings on unmanned vehicles. Designs are tested to their full pressure rating.
Production units are pressure-tested to a nominal rating to ensure no leaks. If using our equipment on vehicles containing people, you
do so at your own discretion as SubC does not certify equipment for direct human contact underwater. Manned submersibles require
equipment to have additional pressure-testing to ensure safety.
2. The equipment has been designed for subsea usage. Observe the operating temperature specifications before prolonged usage in air
(do not operate for >10 minutes in air). Run equipment in water.
3. The power supply is polarized. Ensure the correct polarity is used before plugging into the unit. There are many built-in protections on
the bulkhead pins, however, incorrect electrical connections may still damage the internal electronics. See your equipment datasheet
for correct wiring. Some equipment has a custom pinout selected at point of sale. Check your documentation before powering.
4. Water should not come in contact with the pins on the bulkheads. When not in use, use dummy plugs. If water touches the pins, use
contact cleaner and compressed air to remove the water.
5. Before attaching the connector to the equipment, be certain that the pins are aligned, clean and lightly lubricated with appropriate
silicone o-ring grease (Molykote 44 Medium Lubricant or equivalent).
6. All fasteners on the equipment are metric. They should be hand tightened during regular maintenance.
7. When turning on and working with lasers, do not stare into the beam. Staring directly into the beam or
the reflected beam can cause permanent eye damage. Ensure you are always wearing the supplied
laser safety glasses.
8. Please refer to the regulations according to EN 60825-1 and BGV B2. For laser sources classified in
Laser Classes 3 and 4, please refer to the additional regulations according to EN 207/208 (Laser Safety).
*LED flashing may cause seizures in people who are susceptible
**The customer is responsible for ensuring that the device conforms to Laser Safety Standards. SubC recommends laser safety training.
Camera and Laser Precautions and Maintenance TW: ADR
Mech: BL
PM: CC
Updated:
2021-08-13
4
Best practices for assembling your system
Greasing the Connector/Dummy Plug (ABOVE WATER - DRY MATE ONLY)
A. Connectors must be greased with Molykote 44 Medium (or equivalent)
before every mating. Check the MSDS for your type of o-ring lubricant
before use.
B. A layer of grease corresponding to minimum 1/10 of socket depth should be
applied to the female connector
C. The inner edge of all sockets should be completely covered, and a thin
transparent layer of grease left visible on the face of the connector
D. After greasing, fully mate the male and female connector in order to secure
optimal distribution of grease on pins and in sockets
E. To confirm that grease has been sufficiently applied, de-mate and check for
grease on every male pin then re-mate the connector
O-Ring Lubricant TW: ADR
Mech: BL
PM: CC
5
Best practices for assembling your system
For the fundamentals of how to capture excellent underwater photos and detailed video, check out
our Underwater Photography Guide:
http://ftp.subcimaging.com/docs/SubC_Underwater_Photography_Guide.pdf
1. SubC products are designed to run in water. There is built-in thermal protection in our
equipment, however, we cannot guarantee performance in air.
2. The camera, LED, and laser should be attached to a solid mounting point with either stainless
steel hose clamps OR a machined clamp. In between the mount point and the equipment, use
some neoprene rubber, electrical tape, or similar insulation material to prevent corrosion from
dissimilar metal contact.
3. To limit particle backscatter, the LED should be positioned as far away from the camera as
possible in the system while also angling the light so that there is sufficient overlap. The Rayfin
camera field of view is 80 degrees diagonal and the LED’s beam angle is also matched at 80. So
the light should be slightly further from the scene than the camera, which is easily achievable. If it
isn’t set up properly, you may end up with dark corners in the images.
4. When connecting the cables to the equipment, use o-ring lubricant. See page about o-ring
lubricant.
System Hookup
80˚80˚
TW: ADR
Mech: BL
PM: CC
Packaging & Quickstart
Guides
Included with your Rayfin shipment:
1. Rayfin Benthic 6000m Titanium camera
2. Component compartment:
a. High-pressure dummy plugs for camera Aux0 & Aux1 bulkheads
b. DBH13F test whip bench testing the camera and downloading offline
c. AC cable (matching your region) and AC-DC power supply (24VDC)]
d. Cat5e Ethernet cable
3. Optional Accessories:
a. Aquorea LED(s)
b. MantaRay or Skate Laser(s)
4. Accessory components:
a. (with LED or Skate laser) 3m MCIL5M to MCIL5F cable for Aux ports
b. (with MantaRay) 0.5m Y-splice laser cable to plug into camera
c. (with MantaRay) 2x Titanium clamps for attachment to the camera
5. USB stick with:
a. Windows 10 compatible Rayfin Control Software
b. Product manuals, datasheets and QC documentation
6. Documentation: complete QA checklist, pressure-test certificates,
packing list datasheets, and quick start guide (located under the lid foam)
7. Impact resistant shipping case with designed foam insert
Rayfin Benthic Packaging and QA
PM: CC
Production: JMH Updated:
2021-12-14
7
1
2
3a
3b
5
6
4
7
Required Components
Rayfin Interface cable
Windows PC or laptop AC-DC power supply (24VDC)
Cat5e Ethernet cable AC cable
1. Ensure software is installed by following Software Install instructions.
2. Plug the 13-pin interface cable into camera.
3. Connect Interface Cable to the network or a router with DHCP. The
Windows PC or tablet has to be on the same network as the Rayfin.
4. Connect the AC power supply cable to the Interface Cable
5. Follow Ethernet Connection instructions to connect to the camera from
the Rayfin Control Software.
AC-DC power
supply
Interface cable
Cat5e
Router or
network
PC or laptop (for control)
Rayfin HDE: Ethernet Quickstart
Bench Testing the Camera
8
PM: CC
Production: JMH
Software: AR
Updated:
2021-08-09
Required Components
Rayfin Interface cable
Windows PC or laptop AC-DC power supply (24VDC)
Cat5e Ethernet cable AC cable
HD-SDI cable
1. Ensure software is installed by following Software Install instructions.
2. Plug the 13-pin interface cable into camera.
3. Connect Interface Cable with Cat5e to the network or a router with DHCP. The
Windows PC or tablet has to be on the same network as the Rayfin.
4. Connect the AC power supply cable to the Interface Cable.
5. Immediately after powering on the Rayfin camera, the bootup screen should be
visible on the HD-SDI monitor. It will say “RAYFIN”. A few seconds later it will show
the SubC logo followed by live video.
6. If you cannot see video on the monitor: In software, ensure the camera video is
being transmitted at a framerate and resolution the ROV system mux can handle.
Ex. 1080/30p is HD-SDI (1.5Gbps) and 1080/60p is 3G-SDI (3Gbps).
7. Follow Ethernet Connection instructions to connect to the camera from the
Rayfin Control Software.
AC-DC power
supply Interface cable
Cat5e Router or
network
HD-SDI monitor
HD-SDI cable ROV mux/demux
PC or laptop (for control)
Rayfin HDC: HD over Coax Quickstart
Bench Testing the Camera and Getting Live HD Video
9
PM: CC
Production: JMH
Software: AR
Updated:
2019-11-21
Included with your Rayfin shipment:
1. Rayfin Coastal 500m camera
2. Boost-Power Communication (BPC) Unit
3. Component compartment:
a. High-pressure dummy plugs for camera Aux0 & Aux1 bulkheads
b. MCIL2F BPC Test Cable for bench testing camera and downloading
c. AC cable (matching your region) and AC-DC power supply (24VDC)
d. IP67 Rated Ethernet cable
4. Optional Accessories:
a. Aquorea LED(s)
b. MantaRay or Skate Laser(s)
c. Kevlar Tow Cable with Kellems grip
5. Accessory components:
a. (with LED or Skate laser) 3m MCIL5M to MCIL5F cable for Aux ports
b. (with MantaRay) 0.5m Y-splice laser cable to plug into camera
c. (with MantaRay) 2x Titanium clamps for attachment to the camera
6. USB stick with:
a. Windows 10 compatible Rayfin Control Software
b. Product manuals, datasheets and QC documentation
7. Documentation: complete QA checklist, pressure-test certificates,
packing list datasheets, and quick start guide (located under the lid)
8. Impact-resistant shipping case with designed foam insert
Rayfin Coastal Packaging and QA
PM: CC
Production: JMH Updated:
2021-12-14
1
3
2
4a
4b
6
5a
4c
5b
7
8
10
Andere Handbücher für Rayfin
2
Inhaltsverzeichnis
Andere SubC Imaging Digitalkamera Handbücher
