Suncast Keystone Garage Bedienungsanleitung

Keystone Garage

Assembly Manual

Toll Free: 866.768.8465

Hours: 9-5 Monday-Friday EST

Kit ships as shown

14x24 Garage

Find the assembly manual for this product at

www.HomePlaceStructures.com/manuals

AMISH ORIGINAL

KEYSTONE 14x24 GARAGE

specifications

This flexible building includes an optional heavy-duty floor, 2x4 construction, steep A-frame

roof style, insulated raised-panel steel house doors, dentil molding and keystone trim

pieces, 4 slider windows with screens and shutters, 4 flower boxes, and screened wood

vents. Can be built with or without customer-supplied garage door.

2 Large Wrought

Iron Flower Hooks

Boxed in

12” Gables

Factory Primed Trim

Diamond Plate Threshold

Factory Primed Siding

(Ready for Customer Supplied Paint)

Extra Strong 7’ High

Front and Back Walls

Optional Garage Door

(Supplied by Customer)

Screened Wood Vents

1 Door Keystone Trim Piece

4 Window Keystone

Trim Pieces

Fancy Dentil Molding

Assembled

Peak Height - 11’ 9”

Double Plywood

Gussets

Optional Vented Cupola with Copper Roof

Rafter Ties

2x4 Rafters 16” O.C.

1/2” OSB Sheathing

Steep A-Frame Roof

Shingles

(Supplied by Customer)

Four Large

30x36 Aluminum

Slider Windows

(with screens)

Four Vinyl

Flower Boxes

Real Lock Set

Black Antique Hinges

Four Sets of

Vinyl Shutters

2x4 Sill Plate

24’

wide

Insulated Raised Panel Double House Doors

(Doors can be placed on either end or the front)

13’8”

deep

3/4” Exterior Grade 5-Ply Decking

(with optional floor)

Sidewalls 2x4s 16” O.C.

Treated Bottom Plate

(if purchased without floor)

Treated 2x4 Wood Ramp

(with optional floor)

Keystone Garage

Assembly Manual

revised 10/25/06

Please read through the entire manual before starting!

Note: It is very important that you have a solid, level site for the garden building. If the structure

is being used as a garage for automobiles or other heavy items, the unit must be assembled on

a concrete pad.

When using tools and ladders always follow manufacturer’s recommended safety guidelines!

For proper layout for floor, walls, and roof, please refer to the drawings included throughout

this manual and the set of engineered drawings included at end of manual. The pictures shown

in this manual may depict a different layout, if discrepancies occur always refer to drawings.

Tools Needed:

Level

Screw Gun

Hammer

Tape Measure

Skill Saw

Square

Chalk Line

Pencil

5/16” Drill Bit

Tin Snips

Caulking Gun

Other Items Needed:

Approximately 8 gallons of paint

Approximately 20 Bundles of shingles

Heavy duty Silicone Caulk/Sealer

When your kit arrives, it should look like this.

Inspect the package for any damage that

may have occurred during shipping - dented

corners, punctured plastic, etc. If the pack-

age is damaged, alert HomePlace Structures

immediately - 717.354.2333

14x24 Garage

Hardware & Fasteners

3” 12d Nails

Color Code: Fluorescent

Green

Page 4

2-1/2” 7d Nails

Color Code: Pink

2” 6d Nails

Color Code: Orange

2” Trim Nails

Color Code: Fluorescent

Yellow

1-1/2” Red Shutter Screws

Color Code: Dark Blue

2” Black Hinge Screw

Color Code: Black

1” Pan Head Window Screws

Color Code: Light Blue

1” Roofing Nails

Color Code: Purple

The following fasteners are included with your kit. However, you will find the assembly process to pro-

ceed much faster when using air powered tools and fasteners. When replacing hand fasteners with air

powered fasteners, always use a fastener equivalent.

Note: The universal name for nail thickness is penny, abbreviated d. If you wish to purchase additional

nails at your local supplier, use this terminology to find the appropriate nails.

Page 5

Note: It is important to position 4 joists at end wall underneath

overhead garage door location - overhead door can be positioned on

either end wall.

Optional Floor Assembly

Step 1: Cut open floor kit, cut metal bands, and remove top plywood sheet as shown.

Your floor kit should include all of the following parts:

Page 6

See drawings on previous page for correct layout.

If you did not purchase the optional floor, please proceed to page 8.

Pressure Treated 2”x4”:

34 - 8'

28 - 65”

OSB pieces:

48 - 3-1/2" x 23-1/2"

5/8” Plywood Flooring

8 - 4’x8’ sheets, 2 - 4'x4' sheets

2 - 20"x8', 2 - 20”x4’

Step 2: Layout six 8’ pressure treated 2”x4” floor plates, square joists at one end, and mark off for floor

joists at 12” on center as shown.

Step 3: Layout floor as shown.

Note: See attached drawing

for correct layout.

Step 9: Fasten plywood sections to floor joists using 7d 2-1/4” galvanized nails spaced 8” apart. Note: It

is important to properly align plywood at edges.

Step 4: Attach short floor joists

to long floor joists using using 6d

2” nail and OSB pcs, keeping all

pieces flush at top.

Step 5: Attach floor joists togeth-

er at appropriate measurements

using two 12d 3” nails per joist

Step 6: Attach outside band-

board joists together as shown.

Step 7: Make sure floor is

square. Floor is square when

diagonal measurements are

equal (approximately 27’5/8”).

Step 8: Layout plywood floor

sections as shown.

page 7

Tip: It is

important

to level

floor

before

proceed-

ing to

step.

Bottom Wall Plate Layout

for Units without floor

Step 10: Cut open large package and remove packing materials repeating step 1.

Step 11: Remove top layer of

4’x8’ OSB roof sheeting and

place to the side.

Note: Unpack kit all the way

down to layer 5.

Note: If you purchased the optional floor, please proceed to back wall layout and assembly page.

Step 12: Remove next layer of

kit and set aside.

Step 13: Remove screws from

4’-2”x4” double wall plates and

set aside.

Step 14: Remove all remaining

pieces (excluding pressure treat-

ed 2”x4” bottom wall plates)

Step 15: Measure a square

pad at 13’8”x24’ and snap lines

as shown. Make sure layout is

square, see step 19.

page 8

Step 16: Layout 6’ pressure treated bottom plates as shown.

Step 17: Mark and cut bottom plates to fit.

See step 17

Step 18: It is recommended to

put a layer of clear silicone seal-

er under bottom plates.

Step 19: Make sure bottom plate

layout is square. It is square

when diagonal measurements

are equal.

Step 20: Fasten bottom plates to

surface using concrete screws,

tapcons, or fastener equivalent.

Bottom plate layout is complete.

page 9

Page 10

Inhaltsverzeichnis

Andere Suncast Zelt Handbücher

Suncast

Suncast GS8500 Bedienungsanleitung

Beliebte Zelt Handbücher anderer Marken

OZTENT

OZTENT JV SIGNATURE EDITION Bedienungsanleitung

GigaTent

GigaTent Summer Chalet Mini Tent Bedienungsanleitung

ShelterLogic

ShelterLogic 107153 Bedienungsanleitung

Outsunny

Outsunny 84C-230 Bedienungsanleitung

Napier

Napier SPORTZ COVE 61 Series Bedienungsanleitung

EuroTrail

EuroTrail ATLANTIS PRO Bedienungsanleitung

Reimo

Reimo Marina Bedienungsanleitung

TiiTENT

TiiTENT TB300 Bedienungsanleitung

Coleman

Coleman 2000033134 Installationsanleitung

Ozark Trail

Ozark Trail W784.1 Kurzanleitung

SlingFin

SlingFin CrossBow 2 Bedienungsanleitung

Coleman

Coleman 9600-141 Bedienungsanleitung

Palram

Palram Arizona 5000 Wave - WINGS Bedienungsanleitung

COVERPRO

COVERPRO 56184 Montageanleitung

Vango

Vango Zenith 100 Bedienungsanleitung

Costway

Costway PATIOJOY OP70818 Bedienungsanleitung

Clarke

Clarke PUC 88 Bedienungsanleitung

Coleman

Coleman MONTANA 14'x7' Bedienungsanleitung