Sundstrom SR 99 Bedienungsanleitung

…prepare your supplied-air

system

Air quality

If you are using a compressor or pump to supply

breathing air to the user, the placement of the

air intake is crucial. The air at the source:

•Must have a minimum of impurities.

•Must never exceed the hygienic limit

level.

•Must contain so little mineral oil that no

smell of oil is detectable (usually less

than 0.3 mg/m³).

•Must ensure that the dewpoint of the air

is so low that no water condensation will

occur.

Setting up the system

A fixed supplied-air system has to be designed,

constructed and maintained properly. While

many air tools can be operated on unfiltered air,

breathing air should always be clean and free of

humidity, oil and smells.

Watch this on

(using your SmartPhone, tablet or computer)

Scan the QR-code or enter the internet address

in your browser.

(http://youtu.be/7BK40r0xfPc)

The supply line from the air source to the

supplied-air filter must be at least 11 mm in

inside diameter.

A thinner hose or pipe may restrict maximum

airflow.

…prepare the SR99

Inlet

The inlet thread is a ½” BSP female. Fit a suitable

coupling/nipple that matches your fixed

supplied-air system.

Outlet

There are two 1/2" BSP female outlets (one

outlet is plugged on delivery). The unit is

supplied with one CEJN 342 series coupling. Fit

the supplied coupling to the open outlet.

…make 2 outlets

Remove the plug and fit a second outlet coupling

(not supplied).

…make 3 outlets

Connect the Y-coupling to one of the outlets.

You now have 3 outlets.

…drain the water trap manually

The water trap drains itself automatically as soon

as the air supply is turned off.

You can also drain it manually by pressing on the

drain valve at the bottom of the bowl with a

screwdriver or similar.

IMPORTANT!

Draining the water trap manually will also

depressurise the entire SR99.

Before performing any maintenance on the

SR99, switch off the air source, disconnect the

supply hose, and depressurise the SR99 as

shown.

…remove the filter

•Turn off the air supply or disconnect the

incoming air.

•Drain the water trap manually. This will

also depressurise the entire SR99 unit.

•Turn the SR99 upside-down.

•Push the red ring on the hose connector

on the filter, and disconnect the hose.

•Unscrew all 4 knobs holding the lid. Lift

off the lid.

•Lift out the filter itself.

…check whether the filter needs

to be replaced

•If you can smell or taste any impurities in

the breathing air, replace the filter

immediately.

•Check the date stamp on the filter. If the

date has expired, fit a new filter.

•Under normal conditions, the filter

should last around 6 months, but this

can vary greatly depending on a range of

operational and environmental factors.

•One way of checking whether the filter

needs to be replaced is to weigh it. The

weight of the filter when it was unused is

displayed on the filter exterior. If the

weight has increased by 100–150 grams,

replace the filter.

…fit a new filter

Put the filter components back in reverse order.

The filter ends are identical, and it doesn’t

matter which way the filter is inserted.

Pay attention to the order and number of the

sealing rings (A, D and E in the picture).

Ensure that the lid fits snugly, and that the end

caps fit into their respective grooves.

…clean the pre-collector

•

Turn off the air supply or disconnect the

incoming air.

•Drain the water trap manually. This will

also depressurise the entire SR99 unit.

•Turn the SR99 upside-down.

•Remove the outer guard. Slide the black

locking device down, and turn the outer

guard anti-clockwise (bayonet fitting).

Lift off.

•Remove the bowl. Push down and turn

anti-clockwise (bayonet fitting). Lift off.

•Wash the bowl in maximum +60°C water

only. Do not use solvents.

•Unscrew and remove the collector

element.

•Blow-clean and dry all parts with a

supplied-air gun.

•Reassemble all parts in reverse order.

…clean the exterior of the SR99

Use a mild detergent and water and wipe the

exterior of the filter with a soft cloth, sponge or

brush. Warm water may give a better clean.

Leave to dry and store in a dry, clean area at

room temperature away from direct sunlight.

The unit can also be cleaned and blow-dried with

a supplied-air gun.

IMPORTANT! Never use solvents to clean the

equipment.

Watch this on

(using your SmartPhone, tablet or computer)

(

http://youtu.be/Tt6Q4uDvHrY

)

Andere Handbücher für SR 99

Inhaltsverzeichnis

Andere Sundstrom Luftreiniger Handbücher

Sundstrom

Sundstrom SR 99 Bedienungsanleitung

Beliebte Luftreiniger Handbücher anderer Marken

IKEA

IKEA UPPÅTVIND Bedienungsanleitung

Nash

Nash AP-1 PureSmart Bedienungsanleitung

LG PH-U450 Series Bedienungsanleitung

DeLonghi

DeLonghi DDSX 220WFA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Bedienungsanleitung

Sharp

Sharp FU-40SE Bedienungsanleitung

Philips

Philips AC2721 Bedienungsanleitung

TruSens

TruSens Z-2000 Bedienungsanleitung

Motorola

Motorola MBP87SN Bedienungsanleitung

Beko

Beko ATP 7100I Bedienungsanleitung

Carrier

Carrier INFINITY 1620 Bedienungsanleitung

AtmosAir

AtmosAir P2002 Bedienungsanleitung

Winix

Winix NK300 Bedienungsanleitung

Friedrich

Friedrich C-90A Bedienungs- und Montageanleitung

Surgically Clean Air

Surgically Clean Air JADE2.0 Bedienungsanleitung

Base aire

Base aire 555 Pro Bedienungsanleitung

Champion

Champion CP25 Bedienungsanleitung

vollara

vollara Air & Surface Pro+ Bedienungsanleitung