Sundstrom SR 580 Bedienungsanleitung

2020-05-18

OI06H-8018 SR 580 1

Operating instruction

SR 580

Protective helmet with visor

Revision: 04

General information

Instructions for use for SR 580 should be read before use.

SR 580 together with the fan unit SR 500/SR 500 EX/SR 700 and approved filters is included in the

Sundström fan-assisted respiratory protective device system conforming to EN 12941/ EN 12942:1998

SR 580 can be used together with fan unit SR 500 EX in explosive atmospheres.

SR 580 can also be used together with compressed air attachment SR 507 (fig. 1). This combination forms a

breathing apparatus designed for continuous air flow, for connection to a compressed air supply in accordance

with EN 14594:2005.

When selecting the head top, some of the factors that must be taken into account are as follows:

•Potentially explosive atmosphere.

•Concentrations.

•Work intensity.

•Protection requirements in addition to respiratory protective device.

The risk analysis should be carried by a person who has suitable training and experience in the area.

2020-05-18

OI06H-8018 SR 580 2

Unpacking SR 580

Packing list:

•Complete SR 580

•Breathing hose

•User instructions

•Cleaning tissue

2020-05-18

OI06H-8018 SR 580 3

1. Control and donning of the hose

2020-05-18

OI06H-8018 SR 580 4

1.1 Check that the O-ring of

the hose is in place and is

undamaged.

1.2 Check that the thread is

ok.

1.3 Mount the hose with the

nut in the helmet.

1.4 Mount the hose in the fan.

2. Functional check

2020-05-18

OI06H-8018 SR 580 5

2.1 Turn the flow meter bag

inside out and the flow meter

appears

2.2 Place the head-top in the

flow meter and start the fan

unit. Grip the bag to seal

around the breathing hose.

Grip the flow meter tube with

the other hand, the tube will

point upwards from the bag

Read the position of the ball

in the tube. This should hover

at a level with or slightly

above the upper marking on

the tube, (175 l/min).

If minimum flow is not

achieved, check that

-the flow meter is held

upright,

- the ball moves freely,

- the bag seals well around

the hose.

3. Putting the helmet on

2020-05-18

OI06H-8018 SR 580 6

3.1 Check that the 6-point

harness is secured correctly.

3.2 Raise the visor and put on

the helmet. If necessary,

adjust the width of the helmet

using the knob located at the

rear of the harness.

3.3 To adjust the height of the

helmet interior, move the pins

between positions. If the

interior is attached to pin a,

the helmet will sit lower, and

on pin b the helmet will be

higher. To achieve the best fit,

this adjustment can be made

at both the front and back of

the helmet.

3. Putting the helmet on

2020-05-18

OI06H-8018 SR 580 7

3.4 Lower the visor by pulling

the face seal down below

your chin. A ‘click’ indicates

that the visor is fully lowered.

3.5 Insert a finger inside the

face seal and move it along

the length of the contact

surface to check the fit.

3.6 Make sure that the

breathing hose runs down

your back and is not twisted.

You can adjust the angle of

the helmet connection as

required.

4. Replacement of exhalation membrane

2020-05-15

OI06H-8018 SR 580 8

4.1 The exhalation membrane

is fitted on a pin inside the

valve cover. The cover must

be replaced at the same time

as the membrane. Do the

following:

Remove the valve cover from

the valve seat

4.2 Pull out the membrane.

Check and, if necessary,

clean the seal groove in the

valve seat.

4.3 Press the new membrane

securely on the pin. Carefully

check that the membrane is

fully in contact with the valve

seat.

4.4 Press the valve cover

firmly back into position. A

‘snap’ indicates that it is

locked in position.

5. Replacement of visor

2020-05-18

OI06H-8018 SR 580 9

5.1 Unhook the face seal

from the harness.

5.2 Remove the lower visor

frame

5.3 Remove the visor

5. Replacement of visor

2020-05-18

OI06H-8018 SR 580 10

5.4 Fit the visor into the lower

visor frame.Applying a little

water to the seal will make

fitting easier.

5.5 Fit the lower visor frame

to the helmet by sliding it into

position. A ‘click’ indicates

that is locked in position.

5.6 Check that the visor has

achieved a full seal around

the entire visor frame.

5.7 Attach the hooks in the

harness.

Andere Handbücher für SR 580

Inhaltsverzeichnis

Andere Sundstrom Motorradzubehör Handbücher

Sundstrom

Sundstrom SR 580 Installations- und Benutzerhandbuch

Sundstrom

Sundstrom SR 591 Bedienungsanleitung

Sundstrom

Sundstrom SR 580 Bedienungsanleitung

Sundstrom

Sundstrom SR 574 Montageanleitung

Sundstrom

Sundstrom SR 592 Bedienungsanleitung

Sundstrom

Sundstrom SR 580 Bedienungsanleitung

Sundstrom

Sundstrom SR 580 Bedienungsanleitung

Sundstrom

Sundstrom SR540 Bedienungsanleitung

Sundstrom

Sundstrom SR 580 Installations- und Benutzerhandbuch

Sundstrom

Sundstrom SR 580 Bedienungsanleitung

Sundstrom

Sundstrom SR 574 Montageanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

SW-Motech

SW-Motech SBL.01.971.10000/B Bedienungsanleitung

GÜDE

GÜDE GSH 180-TC-2 Bedienungsanleitung