Sunjoe SJPH1500E Bedienungsanleitung

A Division of Snow Joe®, LLC Model SJPH1500E Form No. SJ-SJ-SJPH1500E-880E-M

OPERATOR’S MANUAL

ELECTRIC INFRARED HEATER

1500-WATT | FREE STANDING + WALL-MOUNTED

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Read all the instructions contained in this manual. Keep this

manual in a safe place, so that the information is available at

all times. If you give this equipment to another person, make

sure to provide these operating instructions. Basic safety

precautions should always be followed to reduce the risk of

explosion, which could cause property damage, personal

injury, or death.

Notice the safety alert symbol mused in this manual to draw

your attention to a WARNING given along with the particular

operating instruction. This means that the operation requires

special ATTENTION, CAUTION, and AWARENESS.

mWARNING! Surface temperatures become very

hot when operating the heater.

mWARNING!

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. If provided, use handles

when moving this heater. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and

curtains at least 3 feet (0.9 m) from the front of the heater

and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by

or near children and whenever the heater is left operating

and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or plug

or after the heater malfunctions, has been dropped or

damaged in any manner. Discard heater, or return to

authorized service facility for examination and/or repair.

6. This heater is not intended for use in bathrooms, laundry

areas and similar indoor locations. Never locate heater

where it may fall into a bathtub or other water container.

7. Do not run cord under carpeting. Do not cover cord with

throw rugs, runners, or similar coverings. Do not route

cord under furniture or appliances. Arrange cord away

from trac area and where it will not be tripped over.

8. After shutting down the heater, remove plug from outlet.

9. Connect to properly grounded outlets only.

10. Do not insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an

electric shock or re, or damage the heater.

11. To prevent a possible re, do not block air intakes or

exhaust in any manner. Do not use on soft surfaces, like a

bed, where openings may become blocked.

12. A heater has hot and arcing or sparking parts inside. Do

not use it in areas where gasoline, paint, or ammable

liquids are used or stored.

13. Use this heater only as described in this manual. Any

other use not recommended by the manufacturer may

cause re, electric shock, or injury to persons.

14. Always plug heaters directly into a wall outlet/receptacle.

Never use with an extension cord or relocatable power tap

(outlet/power strip).

15. This heater is NOT to be operated by children.

16. The unit must be securely placed on a horizontal and at

surface, with the clearance of 3 ft to the wall and 1 ft to

the ceiling.

17. DO NOT cover the unit with anything during operation or

right after shutting down. Wait for 30 – 45 minutes for the

unit to cool down before storage.

18. DO NOT wrap the power cord on the unit.

19. When damaged, the unit must be repaired by an

authorized service center. If the power cord is damaged, it

must be replaced by the manufacturer, its service agent or

similarly qualied persons in order to avoid a hazard.

20. DO NOT use this heater with a programmer, timer or any

other device that switches the heater on automatically,

since a re risk exists if the heater is covered or positioned

incorrectly.

21. This appliance is NOT intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

22. The unit is for household use only. It's NOT allowed to use

in building site, greenhouses, barn or stable where there's

ammable dust.

23. DO NOT use this unit as a cloth drier or towel drier.

24. DO NOT use this unit as a sauna heater.

25. DO NOT immerse this unit into water for cleaning.

Grounding Instructions

This heater is for use on 120 volts outlet only. The cord has a

plug as shown at A in the gure above. An adapter as shown

at C is available for connecting three-blade grounding-type

plugs to two-slot receptacles. The green grounding lug

extending from the adapter must be connected to a permanent

ground such as a properly grounded outlet box. The adapter

should not be used if a three-slot grounded receptacle is

available.

)(

(C)

Grounding pin

Metal screw

Cover of

grounded

outlet box

Adapter

Grounded means

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

WARNING! Electrical shock hazard.

Symbols SymbolsDescriptions Descriptions

HOT SURFACE – To reduce the risk of injury or damage, avoid contact

with any hot surface.

Know Your Infrared Heater

Read the owner’s manual and safety rules carefully before using your infrared heater. Compare the illustration below to the actual

unit in order to familiarize yourself with the location of the various parts and hardware. Save this manual for future reference.

1. Metal safety bar

2. Heater head

3. Control panel

4. Switch box

5. Power cord

6. Telescoping pole

7. Telescoping coupler

8. Upper pole

9. Remote control

10. Cord clips (2)

11. Middle pole

Hardware Pack

15 16 17

18 19 20 21

12. Lower pole

13. Base

14. Plug

15. Hex key wrench

16. Base washer

17. Heater head knob

18. Wall anchors (4)

19. ST4x30 screws (4)

20. M6x12 screw

21. Wall-mounting bracket

22. Heater head cover

Technical Data

Power Input .................................... 120 V AC | 60 Hz

Maximum Wattage ......................... 1500 W

Heat Output .................................... 5118 BTUs

Heating Area ................................... 130 sq. ft. (12 m2)

Power Cord Length ........................ 6.6 ft. (2 m)

Adjustable Height ........................... 5.25 ft. – 6 ft.

(1.6 m – 1.8 m)

Adjustable Heating Head Angle ..... 0º – 25º

Net Weight ...................................... 26.4 lbs (12 kg)

Unpacking

Carton Contents

• Heater head

• Telescoping pole

• Upper pole with telescoping coupler

• Middle pole

• Lower pole

• Base cover

• Base

• Metal safety bar

• Hardware pack (hex key wrench, base washer, heater head

knob, 4 wall anchors, 4 ST4x30 screws, M6x12 screw, wall-

mounting bracket)

• Heater head cover

• Manual with registration card

1. Carefully remove the infrared heater and check to see that

all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe®+ Sun Joe®customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new infrared

heater. The packaging is made of recyclable materials.

Properly dispose of these materials in accordance with

local regulations.

IMPORTANT! The equipment and packaging material are not

toys. Do not let children play with plastic bags, foils or small

parts. These items can be swallowed and pose a suocation

risk!

Assembly

Tools Required:

• Phillips screwdriver (not provided)

• Hex key wrench

• Drill (not provided)

Choose a spacious and level location for assembly. Remove all

parts from the packaging, and check for missing parts.

Floor Stand Set-up

1. Put lower pole through the base cover, base, and base

washer, tightly lock them with the provided hex key

wrench (Fig. 1).

2. Unscrew the 2 pre-assemble M6x12 screws from the

middle pole, connect the middle pole with the lower pole,

aligning the holes, and tighten with the 2 M6x12 screws

(Fig. 2).

3. Loose the pre-assembled telescoping coupler on the

upper pole, then insert the telescoping pole through the

bottom of upper pole (Fig. 3).

Fig. 1

Lower pole

Base cover

Base

Base washer

Hex key wrench

Fig. 2

Middle pole

Lower pole M6x12 screw

4. Secure the upper pole and the telescoping pole with the

coupler from the top of the telescoping pole (Fig. 4).

5. Unscrew 2 pre-assembled M6x12 screws from the upper

pole, then connect the upper pole assembly with the

middle pole, and tighten with the 2 M6x12 screws (Fig. 5).

6. Unscrew the 4 pre-assembled ST3x10 screws from the

back of the heater head, attach the metal safety bar on

the heater head and secure with the ST3x10 screws

(Fig. 6).

7. Connect the heater head with the telescoping pole with

the holes aligned and tighten with the M6x12 screw in the

hardware pack (Fig. 7).

Wall mount Set-up

NOTE: When mounting the heater head, make sure it's

mounted horizontally, or the tipping over protection will engage

and the unit will not start.

1. Make sure the desired mounting location can t the unit in

a horizontal orientation and is near an outlet but free from

electrical cables, communication lines, and pipes that

could be damaged by excessive heat.

2. Pre-drill the wall and insert the 4 wall anchors. Use the

bracket as a template for hole placement (Fig. 8).

Fig. 3 Telescoping

coupler

Upper pole

Telescoping

pole

Remove the

telescoping

coupler

Insert the telescoping

pole from the bottom of

the upper pole

Telescoping pole

Fig. 4

Telescoping

coupler

Upper pole

Fig. 5

Upper pole

Middle pole M6x12 screw

Fig. 6 Metal safety

bar

Heater head

ST3x10 screws

Fig. 7

Heater head

Telescoping pole M6 x 12 screw

Fig. 8

Wall anchors

3. Use 4 ST4x30 screws to fasten the mounting bracket to

the wall with the wall anchors inside the pre-drilled holes

(Fig. 9).

4. Slide the heater head on the mounting bracket and make

sure the bracket is inserted fully in the heater head

(Fig. 10).

5. Fix the assembly by inserting the heating head knob from

the back of the heater head, screw the knob clockwise

until it cannot be turned further (Fig. 11).

Operation

NOTE: This infrared heater is designed for spot heating or as

a supplementary heat source. It's not intended to be the main

source of heat during cold months.

SwitchOn/O

1. Place the infrared heater on a level and non-combustible

surface. Plug in the appliance to an outlet, making sure

the power supply is same as rated. The indicator light on

the control panel will start ashing, which means it's in

standby status (Fig. 12).

2. Press the "I" button on the control panel to turn on the

heater. The indicator light will illuminate and the heater will

start working (Fig. 13).

Fig. 9

Wall

Wall-anchor in the

pre-drilled hole

ST4x30 screw

Mounting bracket

Fig. 10

Wall

Mounting bracket

Heater head

Fig. 11

Heater head knob

Fig. 12

Plug

Control

panel

Indicator

light

3. To switch o the heater, press the O button on the control

panel of the heater (Fig. 13).

Using the Remote Control

The heater can also be switched on and o with the equipped

remote control. The remote control is powered by two AAA

batteries (not included). Insert the batteries in the battery

compartment on the back of the remote control and use the O

button and I button on the front to control the heater (Fig. 14).

Adjusting the Heating Head

The position and angle of the heating head can be adjusted for

better heating result. Follow the instructions below to adjust

the heating head.

mWARNING! To avoid burns, do not touch the

heater head when the heater is working.

1. The height of the heater head can be adjusted when it's

connected with the oor stand. Before adjusting, make

sure the heater is turned o. Loosen the telescoping

coupler by twisting it counterclockwise. Pull out or push

in the telescoping pole to the desired length. Tighten the

telescoping coupler securely (Fig. 15).

NOTE: Make sure the telescoping coupler is locked

securely after adjusting.

2. To adjust the heater head's angle, grab the heater head

and adjust it to the desired position. The heater head can

be adjust between 0º and 25º (Fig. 16).

NOTE: Make sure the heater is shut o and completely

cooled down before adjusting the heater head's angle.

Overheating Protection

If the infrared heater is overheated, the equipped overheating

protection system will shut o the heater automatically to avoid

danger. Follow the instructions below if this happens during

use:

• Unplug the appliance and let it cool down for 30 - 45

minutes.

Fig. 13

O button

I button

Fig. 14

FRONT

Battery compartment

BACK

Fig. 15

Telescoping coupler

Telescoping pole

Fig. 16

0º

25º

• Remove objects around the appliance to ensure a well

ventilated area.

• When the heater is cooled down, plug in the heater again

and resume using.

Tipping-Over Protection

The infrared heater is also equipped with tipping over

protection, which will turn o the heater when it tilts around 40

degrees or more. Place the heater on a at, smooth, and stable

surface in order to prevent it from tipping over.

Maintenance

To enjoy years of outstanding performance from the infrared

heater, make sure you perform the following maintenance

activities on a regular basis.

mWARNING! DO NOT touch or move the appliance

for at least 30 – 45 minutes after use. Allow all heating

elements to cool before touching.

Cleaning

1. Turn o and unplug the appliance. Wait for the appliance

to cool down completely.

2. Clean the external surface by wiping it with a soft, damp

cloth. Do not use any abrasive detergent on the appliance

as it will cause damage.

Storage

1. Turn o and unplug the appliance. Wait for the appliance

to cool down completely. Store the appliance in a dry,

indoor space covered with the included cover.

2. Do not place any heavy items on top of the appliance as

this may cause damage to the appliance.

Support

If your Sun Joe®SJPH1500E infrared heater requires service or

maintenance, please call 1-866-SNOWJOE (1-866-766-9563)

for assistance.

Model and Serial Numbers

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide

the model and serial numbers, which can be found on the

decal located on the unit. Copy these numbers into the space

provided below.

Record the following numbers from your new product:

Model #:

Serial #:

S J P H 1 5 0 0 E

Inhaltsverzeichnis

Andere sunjoe Heizung Handbücher

sunjoe

sunjoe SJPPH48 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

sunjoe SJPH1500E Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken