Sunjoy A102010000 Bedienungsanleitung

1/ 12

Assembly Manual

Item#: A102010000

Thank you for your purchase! We are pleased that you have chosen Sunjoy for your outdoor

furniture purchase.

Our clear, easy to follow, step by step instructions will guide you through the project from start

to finish

2/ 12

Safety information

•Keep all children and pets away from assembly area. Children and pets should be supervised

when they are in the area of the production construction.

•This package contains small items and plastic bags that should be kept away from children.

•Keep assembly area at least 6 ft. from any obstruction such as a fence, garage, house,

overhanging branches, laundry line or electrical wires.

•Proper placement of your product is essential. Do not place the product underneath electrical

lines.

•Keep fingers away from places where they can be pinched or trapped.

•Some parts may contain sharp edges, wear protective gloves if necessary during assembly.

•When assembling and using this product, basic safety precautions should always be followed

to reduce the risk of personal injury and damage to equipment. Please read all instructions

before assembly and use.

•Check all screws for tightness before and during usage. Ensure that all connectors and poles

are firmly and fully secured into position. It is important to do so before use so as to avoid a

possible collapse or damage to the item, which could also result in injury.

• This product is intended for outdoor use only. Install on flat, level ground.

•Stakes are provided to secure the gazebo in grass ground. If you wish to secure the gazebo

to a wood deck or concrete surface, you will need to purchase fasteners appropriate (such as

expansion bolt) for these surfaces. These are readily available at your local hardware store or

home center.

•The gazebo’s roof and structure are not guaranteed against extreme weather conditions

(storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned

off regularly. Any damage caused by snow accumulation is not covered by the warranty.

•Do not use the unit during an electrical storm, as there is a remote chance of getting struck by

lightening.

•Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will

occur to the structure. Remove fabric roof and secure screen & privacy panels.

•Warranty does not cover damage due to extreme weather conditions.

•Please check your state and local regulations prior to purchasing. Some jurisdictions may

require permits for, or otherwise regulate, installation and use.

Assembly Preparation

• Please read and understand this entire manual before attempting to assemble or install the

product. Keep this manual for future reference.

• Keep the original packaging to store the product.

•Before beginning assembly of product, make sure all parts are present. Do not attempt to

assemble the product if any parts are missing.

•Tools Required for assembly (NOT included): Screwdriver, a hammer, and 2 ladders that are

at least 2.4 m / 7.8 ft in height,

•This unit is heavy. Do not assemble this item alone. At least four or more people are

recommended for safe assembly.

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1 (866) 578-6569 for anytime or email to

[email protected]

3/ 12

Description

Part#

Label

Qty

Image

Post

GZ1080XXX01

Left cross beam of long

side

GZ1080XXX02

Right cross beam of long

side

GZ1080XXX03

Left cross beam of shot

side

GZ1080XXX04

Right cross beam of shot

side

GZ1080XXX05

Parts List

4/ 12

Description

Part#

Label

Qty

Image

Beam connector

GZ1080XXX06

Corner

cover(Outside)

GZ1080XXX07

Corner

cover(Inside)

GZ1080XXX08

Middle beam

connector

GZ1080XXX09

Slanting bar

connector

GZ1080XXX10

Left decorative bar

of long side

GZ1080XXX11

Right decorative

bar of long side

GZ1080XXX12

Left decorative bar

of short side

GZ1080XXX13

Right decorative

bar of short side

GZ1080XXX14

Top frame

GZ1080XXX15

Top frame cover

GZ1080XXX16

Slanting bar

GZ1080XXX17

Middle bar

GZ1080XXX18

Hook

GZ1080XXX19

Left small PC panel

GZ1080XXX20

Left big PC panel

GZ1080XXX21

Middle PC panel

GZ1080XXX22

Right small PC

panel

GZ1080XXX23

5/ 12

Description

Part#

Label

Qty

Image

Right big PC panel

GZ1080XXX24

Long bar cover

GZ1080XXX25

Short bar cover

GZ1080XXX26

Left lock plate of

lower slanting bar

GZ1080XXX27

Right lock plate of

lower slanting bar

GZ1080XXX28

Left lock plate of

lower middle bar

GZ1080XXX29

Right lock plate of

lower middle bar

GZ1080XXX30

Decorative slot

connector

GZ1080XXX31

Left PC panel

connector

GZ1080XXX32

Right PC panel

connector

GZ1080XXX33

Middle PC panel

connector

GZ1080XXX34

Post base

GZ1080XXX35

Base cover

GZ1080XXX36

Left arch support bar

GZ1080XXX37

Right arch support

bar

GZ1080XXX38

6/ 12

Description

Part#

Label

Qty

Image

M6*15 Bolt

BM06015C

M6 Washer

UD06C

108

M6*15 Screw

SM06015C

M6 Wrench

W10D

Hardware Pack 1

Fig.1: Raise up the Base cover(T)and then attach the Post base(S) to the Post(A) by using Screw(CC) and

Washer(BB).

Fig.2-1：Attach the Left cross beam of long side (B1) and Right cross beam of long side (B2) to Beam

connector(C) by Bolt (AA) and Washer (BB).

Fig.2-2：Attach the Left cross beam of short side (B3) and Right cross beam of short side (B4) to Beam

connector(C) by Bolt (AA) and Washer (BB).

7/ 12

Description

Part#

Label

Qty

Image

M6*15 Bolt

BM06015C

M6 Washer

UD06C

Hardware Pack 2

Fig.3-1：Attach the Middle beam connector (F) to the Left cross beam of short side (B3) and Right cross

beam of short side (B4) by Bolt (AA) and Washer (BB).

Fig.3-2：Attach the Middle beam connector (F) to the Left cross beam of long side (B1) and Right cross beam

of long side (B2) by Bolt (AA) and Washer (BB).

Fig.4：Attach the assembled cross beam (B1) and (B3) to the Post (A) by Bolt (AA) and Washer (BB), Use

the same way to assemble the cross beam (B3) and (B4).

Fig.5：Attach the Slanting bar connector (G) to the cross beam of long side (B1/B2) and cross beam of short

side (B4/B3) by Bolt (AA) and Washer (BB).

Fig.6：Attach the arch support bar(U1,U2) to the cross beam(B1、B2、B3、B4) and Post (A) by Bolt (AA)

and Washer (BB).

8/ 12

Hardware Pack 3

Description

Part#

Label

Qty

Image

M6*15 Bolt

BM06015C

M6 Washer

UD06C

M6*45 Bolt

BM06045C

Φ8*260 Stake

DD08260C

Fig.9：Attach the upper end of the Middle bar (K2) to the Top frame (I) by Bolt (AA) and Washer (BB).

Fig.10：Attach the lower end of the Middle bar (K2) to the Middle bar connector (F) by Bolt (AA) and

Washer (BB).

Fig.11：Attach the Top frame cover (J) to the Top frame (I) by Bolt (AA) and Washer (BB), then screw

the Hook (L) to the Top frame (I).

Fig.7：Four people and two ladders are needed to assemble during this step.

Note1: Two people to assemble the upper end of slanting bar, another two people to assemble the lower

end of the slanting bar.

Note2: Assemble the middle bar by the same way.

Fig.7-1：Attach the upper end of the Slanting bar (K1) to the Top frame (I) by Bolt (AA) and Washer (BB).

Fig.8：Attach the lower end of the Slanting bar (K1) to the Slanting bar connector (G) by Bolt (AA) and

Washer (BB).

9/ 12

Fig.12：Insert the left small PC panel (M1) to the slot of the Slanting bar (K1) and Middle bar (K2). Assemble

the Right small PC panel (M4) and the Middle PC panel (M3) by the same way.

Fig.13：Insert the Left PC panel connector (R1) into the slot of Slanting bar (K1) and Middle bar (K2).

Assemble the Right PC panel connector (R2) and Middle PC panel connector (R3) by the same way.

Fig.14：Insert the Left big PC panel (M2) to the slot of the Slanting bar (K1) and Middle bar (K2). Assemble the

Right big PC panel (M5) and the Middle PC panel (M3) by the same way.

Fig.15：Attach the Right lock plate of lower slanting bar (P2) to the Slanting bar connector (G) by the Bolt (AA)

and Washer (BB).Attach the Left lock plate of lower slanting bar (P1) to the Slanting bar connector (G) by the

same way.

Fig.16：Attach the Left lock plate of lower middle bar (P3) to the Middle beam connector (F) to keep the Left

big PC panel (M2) stable by Bolt (AA) and Washer (BB). Use the same way to assemble the Middle PC

panel (M3) by Left lock plate of lower middle bar (P3) and Right lock plate of lower middle bar (P4). Make

sure all the Bolts are screwed tightly.

10 / 12

Fig.18-1: Attach the Left decorative bar of long side (H1) and Right decorative bar of long side (H2) to the

Middle bar (K2) by Bolt (AA) and Washer (BB).

Fig.18-2: Attach the Right decorative bar of short side (H4) to the Middle bar (K2) by Bolt (AA) and Washer

(BB).

Fig.19: Attach the Decorative slot connector (Q) to the Left decorative bar of short side (H3) and Right

decorative bar of short side (H4) by Bolt (AA) and Washer (BB). Attach the connector (Q) to decorative bar

(H1) and (H2) by the same way.

Fig.17-1：Attach the Left decorative bar of long side (H1) to the Right decorative bar of long side (H2) as

the fig.17-1 shows. Assemble the decorative bar H3 & H4 by the same way.

Fig.17-2.Attach the decorative bar(H1, H2, H3, H4) to the cross beam (B1、B2、B3、B4) as the fig.17-2

shows. (Note: Two people are needed during this step.)

Fig.20-1: Attach the Short bar cover (O2) to the connecting part of Left decorative bar of long side (H1) and

Right decorative bar of long side (H2) by Bolt (AA) and Washer (BB).

Fig.20-2: Attach the Long bar cover (O1) to the decorative bar (H1/H3) and decorative bar (H2/ H4) as the

Fig.20-2 shows.

Fig.21: Put Corner cover (Outside) (D) through Post (A) to the corner of decorative bar (H1/H3) and

decorative bar (H4/H2), fix them by Bolt (FF) and Washer (BB).

Fig.22：Attach the Corner cover (Inside) (E) to the Post (A) by Bolt (AA) and Washer (BB).

Fig.23：Fix the assembled gazebo to the ground by using Stakes (II).

Inhaltsverzeichnis

Andere Sunjoy Gartenmöbel Handbücher

Sunjoy

Sunjoy A102007903 Beilage

Sunjoy

Sunjoy South Hampton L-GZ215PST-A-MN Bedienungsanleitung

Sunjoy

Sunjoy A106008100 Bedienungsanleitung

Sunjoy

Sunjoy A102009100 Beilage

Sunjoy

Sunjoy L-GG001PST-F-PK Bedienungsanleitung

Sunjoy

Sunjoy D-BG001PST Bedienungsanleitung

Sunjoy

Sunjoy L-GZ1081PCO-A Bedienungsanleitung

Sunjoy

Sunjoy D-GZ806PAL-A Bedienungsanleitung

Sunjoy

Sunjoy 10’x12’ Benen Gazebo L-GZ215PST-1 Bedienungsanleitung

Sunjoy

Sunjoy L-GG001PST-H Bedienungsanleitung

Sunjoy

Sunjoy L-GZ025PCO-7A Bedienungsanleitung

Sunjoy

Sunjoy L-GZ120PST-9D Bedienungsanleitung

Sunjoy

Sunjoy A101006400 Bedienungsanleitung

Sunjoy

Sunjoy A207000701 Bedienungsanleitung

Sunjoy

Sunjoy D-GZ841PST-C Bedienungsanleitung

Sunjoy

Sunjoy D-BS692SAL Bedienungsanleitung

Sunjoy

Sunjoy Havenbury Gazebo Bedienungsanleitung

Sunjoy

Sunjoy OXFORD A101002600 Bedienungsanleitung

Sunjoy

Sunjoy A103002000 Bedienungsanleitung

Sunjoy

Sunjoy 243341 Bedienungsanleitung

Sunjoy

Sunjoy A202000502 Bedienungsanleitung

Sunjoy

Sunjoy Healdsburg Gazebo Bedienungsanleitung

Sunjoy

Sunjoy L-GZ717PST-E Bedienungsanleitung

Sunjoy

Sunjoy L-GZ212PCO-B1 Bedienungsanleitung

Beliebte Gartenmöbel Handbücher anderer Marken

Belleze

Belleze 014-HG-20074 Bedienungsanleitung

Hatteras Hammocks

Hatteras Hammocks DCA1-K-HH Bedienungsanleitung

Kozyard

Kozyard Morgan Aluminum Pergola Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5959 Installationshandbuch

OLT

OLT 24 Bedienungsanleitung

forest-style

forest-style HACIENDA 2354 Bedienungsanleitung

Courtyard Creations

Courtyard Creations RUS0188-WM Bedienungsanleitung

RPR

RPR OLLIE CHAIR Bedienungsanleitung

kingsley-bate

kingsley-bate MC-55 Bedienungsanleitung

Weltevree

Weltevree Carrier Bedienungsanleitung

Grange Fencing

Grange Fencing Elite Arch Bedienungsanleitung

Grosfillex

Grosfillex AUVENT YR14 Bedienungsanleitung

X-METAL

X-METAL EAGLE 33511 Bedienungsanleitung

Anova

Anova FBW6R Bedienungsanleitung

Outsunny

Outsunny 84A-090 Bedienungsanleitung

Ivy Terrace

Ivy Terrace IVTD212 Bedienungsanleitung

Breezesta

Breezesta FANBACK ADIRONDACK AD-0101 Bedienungsanleitung

hanit

hanit SUTTON 1 Bedienungsanleitung