Sunpak Folding Vlogging Kit Bedienungsanleitung

1. Your kit comes

retracted so that it’s

only 2.76” high for

easy transport. In

order to set up your

unit, first lift the ring

light out of the base.

Loosen the Ring

Light Lock Knob to

allow the light to

swivel.

2. As you are extracting

the ring light from the

base, bring the center

column to a vertical

position.

3. Once vertical, tighten the

Ring Light Lock Knob, so that it

is secure prior to mounting your

smartphone or camera to the

ring light.

Ring Light

Lock Knob

4. Loosen the Extendable Column

Locking Collar at the bottom of the

column by rotating it counter-clockwise

to allow you to slide the Extendable

Column toward the center of the base.

5. When the Extendable Column is at

the center of the unit, tighten the lock-

ing collar by rotating it clockwise to

lock it in place.

6. While holding the base, pull up on

the top of the column (the base of

the ring light) to raise the ring light to

your desired height.

You may encounter some resistance

when pulling it up. This is a normal

function of the column in order to

keep it from self-collapsing.

Extendable Column

Locking Collar

7. You can fully extend the column to a full 54" and use it

as a floor standing unit or collapse the column and use it

as a tabletop unit

***Warning***

When used in any of the extended height set-

tings, do not mount a camera in this mode.

When using a camera or any device other than

a smartphone, only use it at the shortest

height (tabletop mode) to avoid the possibility

of accidentally tipping over.

Correct Correct Correct Wrong

8. When mounting a camera, first remove the Flexible

Smartphone Mount from the ring light. Lock the head of

the ball head and install the ball head to the 1/4”-20 recep-

tacle on the bottom of your camera. Screw the base of the

ball head into the threaded socket of your ring light by

rotating the camera while it is mounted on the ball head.

Note: You may need to remove the lens from your

camera body as you are rotating the camera and ball

head onto the ring light. Likewise, when removing the

camera from the ring light, you may need to remove

your lens from the camera body prior to uninstalling

your lens.

When using a camera, only use the ring light in

the lowest setting (as pictured below).

9. To mount the microphone:

Your BOYA microphone can be

mounted to the ring light via the

included folding bracket, which has

two 1/4”-20 screws at opposite

ends.

Screw the shock mount of your

microphone to the 1/4”-20 threaded

screw, of the bracket and then

screw the other end of the bracket

to the 1/4”-20 mount underneath

your ring light.

You can position the folding bracket

in various positons (see below).

10. To use your Bluetooth remote, follow these steps:

 Turn the On/Off Switch on the Bluetooth Remote to the

“On” position.

 Turn on your smartphone’s Bluetooth function. When

you see SUNPAK in your list of Bluetooth devices, pair

your phone to that device.

 Once paired, open up the camera feature of your

smartphone.

 Attach your phone to the smartphone mount. The

smartphone mount can accept phones up to 3.5” wide.

 To take a picture, press the Shutter Release button on

the Bluetooth remote. For Apple (iPhones), press the

iOS button. For Android phones, press the Android but-

ton.

Note: Some Android users may notice the camera

zooming when the Shutter Button on the remote is

pressed. If this occurs, please go into your

smartphone’s camera settings and change the “Volume

Key” setting to “Camera”. Please refer to your

smartphone manual for assistance in changing this

setting.

Note: You cannot pair more than one remote at the same

time.

On / Off

Switch

Android Shutter

Button

Apple Shutter

Button

Sunpak One Year Limited Warranty

This Sunpak product has been carefully manufactured, accurately adjusted, inspect-

ed and thoroughly tested before shipment to assure you of the highest quality.

Should this product require service, we will repair or replace, at our option, any part

or the product itself, which our examination shows to be defective in material or

workmanship. This warranty does not apply to wear and tear associated with the

normal use of the product. This warranty is non-transferable.

Repairs will be made to the product at no charge, under the terms of the warranty as

stated above, only when accompanied by a dated and itemized bill of sale and

nominal handling charge.

Be certain to follow all assembly and/or operating instructions with this product. This

warranty is not valid if the product has been misused or damaged in any way that is

beyond our control or through normal wear and tear associated with use. This

warranty applies only to the product and we are not responsible in any way for

losses, damages or any inconvenience caused by equipment failure.

Some states do not allow the exclusion or limitation of consequential damages, so

the above limitation or exclusion may not apply to you. This warranty gives you

specific legal rights and you may have other rights which may vary from state to

state.

Should service be required, the product should be carefully packed (in the original

packaging if possible) and sent, prepaid and insured, along with a check or money

order for $9.95 (shipping and handling), to the address listed below. A note briefly

describing the nature of the defect should also be enclosed to expedite handling.

Proof of purchase and payment for shipping and handling must be included

for all warranty repairs.

Sunpak, ToCAD America Inc., 105 West Dewey Avenue, Building D, Units 7-9,

Wharton, NJ 07885 Attention Service Department

Specifications:

 Power; USB 5V Input

 Illumination: 128 high power LEDs

 Light Output: Daylight (5500°K) and Tungsten (3200°K)

 Light Dimensions: Outer: 10.5 inches / Inner: 7.75 inches

 Height: Folded: 2.76 inches / Min: 20 inches / Max: 54 inches

 Maximum Load Capacity: 2.5 lbs.

 Weight: 2.54 lbs.

 Warranty: 1 year limited

Product design and specifications subject to change without notice.

11. Connect the ring light to a USB charger, power bank or

AC adapter (not included). Press and hold the Power

button on the inline remote.

Adjust output intensity by pressing the + or - buttons on the

inline remote.

Change the color temperature by pressing the Color

Temperature button. Brightness Up

Color Temperature

Power

Brightness Down

Inhaltsverzeichnis

Andere Sunpak Handy-Zubehör Handbücher

Sunpak

Sunpak Ultra 7000TM Bedienungsanleitung

Beliebte Handy-Zubehör Handbücher anderer Marken

Valore

Valore AC14 Bedienungsanleitung

X-cam

X-cam X-CAM T3 Bedienungsanleitung

Nokia

Nokia AD-5B Bedienungsanleitung

Bauhn

Bauhn ABSS-1222 Bedienungsanleitung

ReSound

ReSound Phone Clip+ Bedienungsanleitung

Mpow

Mpow ISNAP X1 Bedienungsanleitung

Zartek Mobile

Zartek Mobile ZA-350 Bedienungsanleitung

Playbrush

Playbrush Playbrush Bedienungsanleitung

Sony

Sony SCR44 Bedienungsanleitung

Nautilus

Nautilus V5 Bedienungsanleitung

BigPantha

BigPantha Phone Mount Bedienungsanleitung

PRYME Radio Product

PRYME Radio Product PRYMEBLU BT-PTT-M Bedienungsanleitung

Nokia

Nokia CR-119 Bedienungsanleitung

weBoost

weBoost eqo Bedienungsanleitung

Rollei

Rollei LUMIS Bedienungsanleitung

Morphie

Morphie Juice Pack Helium Bedienungsanleitung

Lenovo

Lenovo SS100 Bedienungsanleitung

Philips

Philips DLA4214 Bedienungsanleitung