SunSynk SUN-8.0 Bedienungsanleitung
Sunsynk Hybrid Inverters with
lithium-ion batteries
Introduction
Sunsynk inverter(s) and lithium-ion batteries is the ideal package for self-consumption, o-grid and back-up
solar PV systems. The Sunsynk hybrid inverter is a bi-directional energy storage unit that consists of the 5kW
and 8kW single phase inverter models. On the other hand, the Pylontech 48V batteries and FreedomWon
range models are the recommended batteries for use with the Sunsynk series inverters.
Interfacing with the Inverter
NB. Only connect the batteries to the inverter until the settings are complete, no PV or grid sources. See
*Note in Battery section
The inverter settings are congured on the touch screen LCD of the inverter.The screen/inverter should come
on when a power source is connected i.e., PV, Grid or Battery. Before installing batteries with the inverter,
please ensure that they are both compatible as the system will not work if the two are not compatible. Below,
Figure 1, is an image of how the settings page of the Sunsynk inverter looks like
Figure 1: Sunsynk settings page
This tab allows the user to enter details such as the time, display name etc. Please ensure that the correct
time settings are entered as this could inuence the functionality of the inverter especially if timed settings
will be use.
Before continuing with the installation, please ensure
that the inverter and battery being installed are
compatible with each other. When the inverter is
connected to the battery, the inverter should be able
to adopt the BMS parameters. This can be checked
under Li-BMS in the settings menu. An example of what
should be seen is in Figure 2 for CAN communication.
Go to the“Battery”under the settings menu. Press“Shut
Down” and set “Shut down” at 3%, “Low Batt” at 5% as
shown in Figure 3. NB: This dier from manufacturer,
please ensure that the correct values are set for batteries
not supplied by Segen.
Press “Batt type”. Choose battery mode “Lithium”, input
the capacity of the battery, charge/discharge currents
according to the battery bank. For the protocol, please
ensure that you follow the notes on the compatibility
table as per manual.Then tick“BMS_Err_Stop”as shown
in Figure 4.
2.1 Basic
2.2 Battery
*Note: Ensure that the Grid and PV power sources are turned o before starting the inverter and until the
battery communication and conguration is successful. Failure to do this could result in the Pylon batteries
being damaged.
Figure 2: Li-BMS page
Figure 3: Battery Shut Down settings
Figure 4: Battery type settings
On the“Battery”page under settings, go to“Batt type”and ensure that“Activate”is ticked and that“Lithium”is
selected as in Figure 4. Freedom Won uses CAN communication so ensure“CAN”is selected and the Protocol
is set to 0. The“Batt capacity”,“Charge Amps”and“Discharge Amps”will be dependent on the type of battery
you have as well as the bank size. Finally, ensure that “BMS_Err_Stop” is ticked.
Sunsynk US3000C/US2000C/UP5000 setup
Before commencing with the installation please ensure that the BMS cable is as per denition in Figure 6.
After the communication cable is connected, please ensure that the Li-BMS page under settings is as in
Figure 2. Please note that values may vary depending on the battery used.
Table 1: Suggested discharge currents
Before commencing with the installation please ensure
that the BMS cable is as per denition in Figure 5. After
the communication cable is connected, please ensure
that the Li-BMS page under settings is as in Figure 2.
Please note that values may vary depending on the
battery used.
Sunsynk Freedom Won setup
Figure 5: Sunsynk and
Freedom Won BMS cable
pinouts
Suggested Discharge Current Limits
Continues Discharge/Charge Current
Note: Pylon connectors are limited to 125A
No batteries per
stack
1 2 3 4 5
Pylontech US2000 25 50 75 100 125
Pylontech US3000C 37 74 111 148 185
Pylontech UP5000 50 100 150 200 250
Figure 6: Pinout congurations for
new Pylontech batteries
Sunsynk US3000/US2000B setup
2.3 System Mode
On the “Battery” page under settings, go to “Batt type” and ensure that “Activate” is ticked and that
“Lithium” is selected as in Figure 4. For Pylontech CAN communication ensure “CAN” is selected and the
Protocol is set to 0. The “Batt capacity”, “Charge Amps” and “Discharge Amps” will be dependent on the
type of battery you have as well as the bank size. Finally, ensure that “BMS_Err_Stop” is ticked
On the “Battery” page under settings these settings will
be the same as that of the other Pylontech batteries i.e.,
US3000C/US2000C and UP5000.
The “System Mode” page is where the installer can program charge and discharge times. These settings are
dependent on the application and purpose the system will serve. For further details please visit the manual.
Figure 4 is an illustration of what each box does and how it can be utilized.
1. Tick this box to do not export power back to the grid (the CT coil will detect power owing back to the
grid and will reduce the power of the inverter only to supply the local load).
2. Tick this box if you wish to export your solar power back to the grid.
3. Tick this box if you only want to supply power to the load side of the inverter.
4. Zero export power is the amount of power owing from the grid to the inverter. Set this value to 20
– 100W to force the inverter to always take this amount of power from the grid to minimize nuisance
tripping “Reverse Power Detection” of sensitive prepaid electricity meters.
5. This controls the maximum overall power, both to the load and grid ports combined. It is set to low if an
over current fault occurs.
6. Tick this box if you wish that the solar panels prioritize power to the load. But if you untick the solar will
prioritize the power to charge the batteries.
Figure 7: Pinout
congurations for old
Pylontech batteries
Before commencing with the installation please
ensure that the BMS cable is as per denition in Figure
7. After the communication cable is connected, please
ensure that the Li-BMS page under settings is as in
Figure 2. Please note that values may vary depending
on the battery used.
Concerning the detailed Figure 4:
The SegenSolar portal has a System Designer tool which allows you to create your systems. Please speak
to your account manager if you require training on how to use the System Design tool. The design tool will
allow you to create a quote quickly and easily with all the necessary components
Figure 8: System Mode page setup
End page
JOHANNESBURG
245 Masjien Street, Strijdompark,
Randburg, Gauteng, 2194
Email: info@segensolar.co.za
Johannesburg: +27 (0) 11 085 2600 /
087 802 0663
CAPE TOWN
1 Gulfstream Avenue
Matroosfontein, Cape Town
Western Cape, 7490
Email: info@segensolar.co.za
Cape Town: +27 (0) 21 001 0589
Inhaltsverzeichnis
Andere SunSynk Wechselrichter Handbücher
SunSynk
SunSynk SUNSYNK MAX Bedienungsanleitung
SunSynk
SunSynk SUN-30K-SG01HP3-EU-BM3 Benutzerhandbuch
SunSynk
SunSynk ECCO SUN-5K-SG05LP1-EU Bedienungsanleitung
SunSynk
SunSynk SUNSYNK-6K-SG02LP1 Benutzerhandbuch
SunSynk
SunSynk SUNSYNK-3.6K-SG01LP1 Bedienungsanleitung
SunSynk
SunSynk SUNSYNK-3.6K-SG01LP1 Benutzerhandbuch
SunSynk
SunSynk LoadShedder SM2.5kWLS Bedienungsanleitung
SunSynk
SunSynk SUN-8K-SG04LP3 Benutzerhandbuch
SunSynk
SunSynk SUNSYNK-L5.1 Bedienungsanleitung
SunSynk
SunSynk BB-300 Bedienungsanleitung
SunSynk
SunSynk SUNSYNK-8K-SG01LP1 Benutzerhandbuch
SunSynk
SunSynk SUNSYNK-8K-SG01LP1 Bedienungsanleitung
SunSynk
SunSynk SYNK-5K-SG03LP1 Benutzerhandbuch
SunSynk
SunSynk SUN-8K-SG04LP3 Bedienungsanleitung
SunSynk
SunSynk SUN-25K-SG01HP3-EU-BM2 Benutzerhandbuch
SunSynk
SunSynk SUN-25K-SG01HP3-EU-BM2 Benutzerhandbuch
SunSynk
SunSynk 8kW Installationsanleitung
SunSynk
SunSynk ECCO SUN-3K-SG04LP1-24-EU Bedienungsanleitung
SunSynk
SunSynk SUN300G3-EU-230 Bedienungsanleitung
SunSynk
SunSynk SUNSYNK MAX Bedienungsanleitung
