SuperDroid Robots HD2 Bedienungsanleitung

SuperDroid Robots, Inc

224 Technology Park Lane, Fuquay Varina, NC 27526

919.557.9162

SDR@SDRobots.com

HD2 TREADED ATR TANK

ASSEMBLY

ROBOTIC PLATFORM

TABLE OF CONTENTS 2

LEGAL INFORMATION 3

SAFETY GUIDE 4

Safety Precautions 4

CHAPTER 1 - ASSEMBLY 5

Motor Electrical Wiring 5

HD2 Kit Wheel Assembly 6

Drive Wheel Shaft Block Mounting 6

Motor Mounting 7

TABLE OF CONTENTS

LEGAL INFORMATION

SuperDroid Robots Inc. is incorporated in Wake County, NC USA

SuperDroid Robots also does business as Team Half-Life

SuperDroid Robots is a registered trademark of Team Half-Life.

Prior to purchasing review our Terms (https://www.superdroidrobots.com/terms.htm)

Accurate content is of the utmost importance to the authors of this document. If you find an error or see an item that needs more

clarification report it to www.superdroidrobots.com

SuperDroid Robots Inc.

https://www.SuperDroidRobots.com

SuperDroid Robots Inc.

224 Technology Park Lane

Suite 100

Fuquay Varina, NC 27526

1. SuperDroid Robots, Inc is not responsible for special incidental, or consequential damages resulting from any warranty or under any

legal theory, including, but not limited to lost profits, downtime, goodwill, damage to, or replacement equipment or property, or any

cost of recovering, reprogramming, or reproducing any data stored. ANY LIABILITY SHALL BE LIMITED TO REPLACEMENT OF

DEFECTIVE PARTS. SuperDroid Robots, Inc. is further not responsible for any personal damages, including, but not limited to bodily

and health damages resulting from any use of our products.

2. SuperDroid Robots, Inc. makes no representations as to the fitness of its products for specific uses. ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS HEREBY EXCLUDED.

3. Agreements shall be construed in accordance with the laws of the State of North Carolina, and the rights and obligations created

hereby shall be governed by the laws of North Carolina.

4. In the event a dispute or controversy arises, such dispute or controversy (including claims of default) shall be brought in the courts

of Wake County, North Carolina and the plaintiff hereby agrees to this choice of venue.

The following section contains a list of non-warrantable items. Any procedure covered in this section will void the coverage warranty of the robot,

or robots, you have purchased.

1. Removal of the lid, or access to the interior of the robot is considered abuse and neglect and as such will void warranty; Unless otherwise

instructed by SuperDroid Robots.

2. Using the robot for purposes that it is not intended, or in any situation that could cause damage outside of the normal wear and tear of the

robot, will not be covered under warranty and be seen as neglect of the robot system.

3. Improper maintenance and overall disregard to the upkeep of the robot can harm, and/or cause severe damage to the robot, leading to

malfunctions and/or destruction of the functionality of the robot.

4. Located throughout the entirety of this document are other warranty voidable perimeters displayed by RED text Any of which will again

cause an immediate void of the warranty and disqualify repairs of the robot.

WARNING - Before using, read this manual to ensure correct usage and operation. After reading, store in a safe place for future

reference. Incorrect handling of this robot could result in personal injury or physical damage. The manufacturer assumes no

responsibility for any damage caused by mishandling that is beyond normal usage defined in these manuals of this product.

SAFETY GUIDE

Thank you for purchasing this product!

This symbol indicates an additional warning (including caution).

The content will be clearly indicated in an illustration or nearby.

This symbol indicates a prohibited action. The content will be

clearly indicated in an illustration or nearby.

NOTE - The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transmission or use of this document or contents is not permitted without express written authority.

Safety Precautions

Do not operate the robot if it isn’t working properly.

If you notice something unusual when operating the robot, immediately stop operating it and turn the unit off. Contact our

technicians at [email protected]om and explain the issue. Unusual can include things such as smoke, strange odor, damage to

the chassis or components etc.

Be careful when operating around children and animals

Children and animals may not understand that the robot has moving parts. Exercise caution when operating the robot and

remain aware of your surroundings.

Do not expose to liquid or insert foreign objects

1. Do not place the robot near water (ex. flooded area, bathroom etc.).

2. Do not expose the robot to rain/moisture. Do not submerge the robot.

3. Do not place containers of liquid such as water on or around the robot.

4. Do not insert any foreign objects into the robot. Please.

5. Avoid placing the robot into a container/bag/case that contains objects besides it’s own components.

Be careful when interacting with internal components of the robot.

The robot contains moving and electric components. Modification and/or disassembly of the robot could result in personal

injury. ALWAYS disconnect the power before working on the robot.

Do not drop, throw, or otherwise cause an impact to the robot

The robot contains moving components, wiring, and electrical systems.

If the robot is dropped or otherwise receives an impact, internal components could be damaged. If the robot is dropped or

otherwise falls and is damaged, turn it off immediately.

Pinching hazard

The treaded ATRs have very powerful motors. The treaded design presents many pinch points! If fingers or hands are inside the

treaded section and the motors energize, injury may occur.

SECTION 1 - MECHANICAL ASSEMBLY

Drive Wheel Shaft Block Mounting

1. Insert the set screws into each block. The set screws need to be adjusted so the screw is set in just enough that the wheel shaft can

be inserted so the set screw is snug on the flat spot on shaft. Insert a wheel shaft into each block to check it. This is most

important on the inside blocks because the set screws can not be easily accessed later.

2. Screw in the tensioning screws and jam nuts. Refer to Fig 1A (interior) and Fig 1B (exterior). Do not tighten at this point.

The tensioning is performed after the treads and outside plates are installed.

3. Insert the carriage bolts through the sides to fasten the tensioning blocks. Tighten them with washers and nylon lock nuts. Refer

to Fig 1C and Fig 1D. Do not tighten the nuts at this point, just snug them up (they should still slide in the slots).

FIGURE 1A FIGURE 1B FIGURE 1C FIGURE 1D

NOTE

The HD2 robot has custom blocks used to align the wheels and tighten the treads. These blocks need to be placed on the inside

and outside plates.

Motor Mounting

This section applies mounting the motors in Treaded ATRs.

NOTE

• Use the proper screw driver on the metric machine screws.

• Wire the motor before installing it as described above

1. The motors need a motor spacer plate between them and the slots cut out in the ATR. Refer to Fig 2A. The HD2 uses a rectangular

one that will be inserted so the long direction goes from front to back of the robot (used to cover the slots).

2. Using the metric machine screws and washers mount the motors shown in Fig 2B. You do not need to fully tighten until you have

installed the chains and treads, etc.

FIGURE 2A FIGURE 2B

Mounting the Sprockets and Chains

This section applies to mounting sprockets and chains. Chains are stronger and less prone to slipping than belts, but require periodic

lubrication and may make more noise.

NOTE

• Working with chains presents pinching hazards. Always disconnect motors and remove power prior to performing work.

• If you need to adjust the length of chain, follow our ‘Chain Cutting Guide’ on our support page.

1. Mount the small sprockets on the motors. The hub should face the motor. Push all the way against the inside plate with enough

clearance for rotation.

2. Tighten the set screw. Refer to Fig 3A and/or Fig3B for placement of the sprocket on the motor shaft.

3. Insert the wheel into the aluminum block that has already been mounted inside the chassis.

4. The chain lengths should be positioned onto the two sprockets. Repeat the process on all four wheels.

SECTION 1 CONTINUED

FIGURE 3A FIGURE 3B

FIGURE 4A

INSIDE

Roller Wheel Mounting

This section applies to mounting the roller wheels on the HD2 tread assembly.

1. Your kit should come with eight (8) roller wheel assemblies, four (4) on each side.

They should come assembled and ready to attach onto the chassis.

2. Insert the roller assembly between the chassis plates. See Fig 4A for alignment

of roller assembly. Use a 3/8” hex bolt to hold the roller in place. Use a wash and

locknut to hold the bolt in place. Tighten the bolt until the sides are snug against

the roller, but still able to spin freely.

3. Repeat on all eight roller wheel assemblies.

SECTION 1 - CONTINUED

Tread Mounting and Alignment

This section applies to mounting the treads and aligning them.

1. The treads can be worked on by rotating them with the wheels. Wrap the tread over one wheel, with the internal cleat straddling

the wheel. Begin to rotate both wheels and push the tread onto the other wheel until it slips into place.

2. Repeat on the other tread.

3. Tension the tracks with the 1/4-20 bolts to move the wheels outward. Evenly tighten each bolt. Tension bolts should be tightened

until the treads are tight. Ensure tension is equal across all four bearing blocks and that all tension bolts are set properly.

4. Tighten the wheel tension block bolts.

5. Tighten the jam nuts against the tension bolt welded nuts.

6. The procedure may need to be repeated when the motors are hooked up. The treads need to run at full speed while spinning freely.

The treads should remain in the correct position while the wheels spin. Repeat the above steps to align wheels and keep tracks

centered. As small as a half turn on the tension blocks can result in a difference in tracking.

7. Slide the motors back in their chassis slots to tension the chain. Tighten the motor mount screws. If the motors experience uneven

loads the chain may be too tight.

NOTE

• Tread alignment is critical. Tighten and align regularly after running the motors.

• Place the robot on blocks to allow treads to rotate freely.

Tread Wheel Mounting

This section applies to mounting the tread wheels on the HD2 tread assembly.

NOTE

• Do not tighten the drive wheel bearings until after the tread is placed on the wheels.

• Do not tighten the idlers. Tightening may prevent the idler from spinning.

1. Place the drive wheels in the front and back. The chain sprockets should be positioned outside of the wheel. Refer to Fig 3A/B.

2. Slide the outside plate on so that both wheel shafts come through the wheel tension blocks.

3. Fasten the side plate on using provided machine screws. Refer to Fig 5A.

4. Tighten the set screws on the wheel tension blocks using an allen wrench. See Fig 5B for set screw placement.

FIGURE 4A FIGURE 4B

SECTION 2 - ELECTRICAL ASSEMBLY

Wiring the Power System

Wiring Motor Controllers

NOTE

• Keep all electrical leads as short as possible to limit electrical noise.

• Controller battery and Motor battery should be different sources to minimize noise.

• Keep signal wires away from power lines.

• Electronics are sensitive to static electricity. Use proper precautions when installing electronic component

• Ensure caution with polarities to prevent damaging components.

• Check power without electronics attached, then slowly add components to prevent damaging system.

1. Internal components may vary based upon the configuration chosen for this kit. Multiple wiring methods are possible as a result.

We recommend viewing the schematics available on our website to assist with wiring your power system. The guides can be found

at the following link: https://www.superdroidrobots.com/shop/custom.aspx/support/1/#Electrical

2. Mount the power switch for your kit.

3. If battery brackets were included in your kit, use these to hold batteries in place. Determine placement of the brackets, then drill

holes in the chassis to match bracket holes. Use provided hardware to tighten bracket in place, with foam underneath the bracket to

ensure a tight fit. Use spacers to prevent the battery from becoming unseated in the bracket. We recommend all screws be installed

inward to prevent protruding threads outside the main chassis.

1. Internal components may vary based upon the configuration chosen for this kit. Multiple wiring methods are possible as a result.

We recommend viewing the schematics available on our website to assist with wiring your motor controllers. The guides can be

found at the following link: https://www.superdroidrobots.com/shop/custom.aspx/support/1/#Electrical

Testing Power System

NOTE

• Keep hands clear of all moving parts.

• Keep the robot raised on blocks when testing the system.

1. Ensure all solder joints are clean and do not cross other connection points. Utilize heat shrink to cover splices properly.

2. Ensure the base of the robot is grounded if wired per schematics mentioned above.

3. Lift the robot onto blocks so that treads do not touch the ground.

4. Make sure all electronics are disconnected before the first power test.

5. Connect the charged batteries. Then, turn on power to make sure wiring is correct.

6. Turn off power and then attach one component. Turn power back on to test that component is powered properly.

7. Repeat Step 6 with each component until all have been tested and connected.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SuperDroid Robots Robotik Handbücher

SuperDroid Robots

SuperDroid Robots WC1500-DM6 Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots IG42-DB2 Montageanleitung

SuperDroid Robots

SuperDroid Robots SGT-32P Montageanleitung

SuperDroid Robots

SuperDroid Robots MLT-JR Montageanleitung

SuperDroid Robots

SuperDroid Robots IG32 DB Montageanleitung

SuperDroid Robots

SuperDroid Robots 2WD Montageanleitung

SuperDroid Robots

SuperDroid Robots TP-150-032 Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots TP-302-001 Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots IG52-SB4-T Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots MiniSLAM Kurzanleitung

SuperDroid Robots

SuperDroid Robots HK1000-DM4-E Montageanleitung

SuperDroid Robots

SuperDroid Robots IG42-SB4-T Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots IG52 DB Montageanleitung

SuperDroid Robots

SuperDroid Robots TP-262-000 Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots IG52-DB Montageanleitung

SuperDroid Robots

SuperDroid Robots GPK-32 Bedienungsanleitung

SuperDroid Robots

SuperDroid Robots LT2-F Bedienungsanleitung

Beliebte Robotik Handbücher anderer Marken

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Bedienungsanleitung

SunFounder

SunFounder PiDog Bedienungsanleitung

Universal Robots

Universal Robots UR5 Bedienungsanleitung

Universal Robots

Universal Robots E Series Bedienungsanleitung

YASKAWA

YASKAWA MOTOMAN-MPL80 II Bedienungsanleitung

EFORT

EFORT ECR5 Gebrauchsanweisung

Epson

Epson C8 Series Bedienungsanleitung

WowWee

WowWee ROBOQUAD Bedienungsanleitung

Milvus Robotics

Milvus Robotics SEIT 100 Bedienungsanleitung

RoboMaster

RoboMaster AI Robot 2020 Standard Version Bedienungsanleitung

fischertechnik

fischertechnik Mini Bots Bedienungsanleitung

YASKAWA

YASKAWA MA2010 Handbuch

Abicor Binzel

Abicor Binzel iCAT mini Bedienungsanleitung

ABB

ABB OmniCore E10 Bedienungsanleitung

YASKAWA

YASKAWA Motoman DX200 Bedienungsanleitung

pitsco

pitsco Tetrix Max Bedienungsanleitung

ECOVACS

ECOVACS DEEBOT R95 Bedienungsanleitung

Feng Yuan

Feng Yuan Interstellar Warrior Bedienungsanleitung