Supermicro SUPER P6DGH Bedienungsanleitung

SUPER P6DGH

USER’S AND BIOS

MANUAL

Revision 1.0

SUPER ®

The information in this User’s Manual has been carefully reviewed and is believed to be

accurate. The vendor assumes no responsibility for any inaccuracies that may be

contained in this document, makes no commitment to update or to keep current the

information in this manual, or to notify any person or organization of the updates.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in

this manual at any time and without notice. This product, including software, if any, and

the documentation may not, in whole or in part, be copied, photocopied, reproduced,

translated or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR

INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE

LIABILITY FOR ANY HARDWARE, SOFTWARE OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA.

Unless you request and receive written permission from SUPERMICRO COMPUTER, you

may not copy any part of this document.

Information in this document is subject to change without notice. Other products and

companies referred to herein are trademarks or registered trademarks of their respective

companies or mark holders.

Printed in the United States of America.

iii

Preface

About This Manual

This manual is written for system houses, experienced PC techni-

cians and knowledgeable PC end users. It provides information for

the installation and use of the SUPER P6DGH motherboard. The

SUPER P6DGH supports Pentium II 233-450 MHz Slot 1 proces-

sors.

The Pentium II processor with Dual Independent Bus Architecture is

housed in a new packaging technology called the Single Edge Con-

tact Cartridge (S.E.C.C.). This new cartridge package and its asso-

ciated "Slot 1" infrastructure will provide the headroom for future

high-performance processors.

Manual Organization

Chapter 1, Introduction, describes the features, specifications and

performance of the SUPER P6DGH system board, provides detailed

information about the chipset, and offers warranty information.

Refer to Chapter 2, Installation, for instructions on how to install the

Pentium II processor, the retention mechanism and the heat sink

support. This chapter also provides you with instructions for han-

dling static-sensitive devices. Read this chapter when you want to

install or remove SIMM/DIMM memory modules and to mount the

system board in the chassis. Also refer to this chapter to connect

the floppy and hard disk drives, IDE interfaces, and the parallel and

serial ports as well as the cables for the power supply, the reset

cable, the Keylock/Power LED, the speaker and the keyboard.

Preface

If you encounter any problems, please see Chapter 3, Trouble-

shooting, which describes troubleshooting procedures for the video,

the memory and the setup configuration stored in memory. Instruc-

tions are also included for contacting a technical assistance sup-

port representative, returning merchandise for service and visiting

our website for BIOS upgrades.

SUPER P6DGH User’s Manual

See Chapter 4 for configuration data and the AMIBIOS features.

Chapter 5 covers the WinBIOS setup options.

Table of Contents

Preface

About This Manual ..................................................................................... iii

Manual Organization .................................................................................. iii

Quick Reference Guide ............................................................................. ix

Chapter 1: Introduction

1-1 Overview........................................................................................... 1-1

SUPER P6DGH Image............................................................. 1-4

SUPER P6DGH Motherboard Layout ..................................... 1-5

SUPER P6DGH Features ........................................................ 1-6

1-2 PC Health Monitoring..................................................................... 1-8

1-3 ACPI/PC 98 Features................................................................... 1-11

1-4 Chipset Overview .......................................................................... 1-12

1-5 Wake-On-LAN................................................................................ 1-13

1-6 Power Supply ................................................................................ 1-13

1-7 Winbond Super I/O Controller...................................................... 1-14

1-8 AIC-7896 SCSI Controller ............................................................. 1-15

1-9 Warranty, Technical Support and Service ................................. 1-16

Parts.......................................................................................... 1-16

BIOS .......................................................................................... 1-16

Labor......................................................................................... 1-16

Returns..................................................................................... 1-16

Chapter 2: Installation

2-1 Pentium II Processor Installation................................................. 2-1

OEM Pentium II and Heat Sink Support ................................ 2-5

Removing the Pentium II Processor...................................... 2-7

2-2 Static-Sensitive Devices ................................................................ 2-8

Precautions................................................................................ 2-8

Unpacking .................................................................................. 2-8

2-3 Changing the CPU Speed............................................................. 2-8

2-4 Mounting the Motherboard in the Chassis ............................... 2-10

2-5 Connecting Cables and Jumpers .............................................. 2-10

Power Supply Connectors ..................................................... 2-11

PW_ON Connector................................................................... 2-13

Infrared Connector ................................................................... 2-13

Reset Header .......................................................................... 2-14

Keylock/Power LED Connector ............................................. 2-14

Hard Drive LED ....................................................................... 2-15

Speaker Connector................................................................. 2-15

AT Keyboard Connector ......................................................... 2-16

Universal Serial Bus ............................................................... 2-16

PS/2 Mouse Header ................................................................ 2-17

Serial Ports .............................................................................. 2-17

Power On/Off State ................................................................. 2-18

CMOS Clear ............................................................................. 2-18

Overheat LED .......................................................................... 2-19

Buzzer Overheat Notification ................................................. 2-19

Chassis Intrusion Connector................................................ 2-19

Wake-On-LAN .......................................................................... 2-20

Fan Connectors ...................................................................... 2-20

i960 Serial Port ....................................................................... 2-21

i960 Fail LED Indicator .......................................................... 2-21

i960 Initialization Modes ........................................................ 2-22

i960 Jumper Settings............................................................. 2-22

I2C Connector .......................................................................... 2-23

SLED (SCSI LED) Indicator................................................... 2-23

I2O Debug LED (Optional)...................................................... 2-24

AT/ATX Power Mode Jumper Settings ................................. 2-24

SCSI Termination Jumper Settings ..................................... 2-25

SUPER P6DGH User’s Manual

Table of Contents

vii

SBLINK Connector .................................................................. 2-26

2-6 Installing/Removing SIMM/DIMM Modules................................. 2-27

SIMM/DIMM Module Installation............................................. 2-29

Removing DIMM Modules ...................................................... 2-29

Removing SIMM Modules....................................................... 2-29

2-7 Connecting Parallel, FDD and HDD .......................................... 2-30

Parallel Port Connector.......................................................... 2-31

Floppy Connector .................................................................... 2-32

IDE Interfaces.......................................................................... 2-33

AGP Port Interface................................................................... 2-34

ULTRA II LVD SCSI Interfaces.............................................. 2-35

Wide SCSI Interface ............................................................... 2-36

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................ 3-1

Before Power On....................................................................... 3-1

Troubleshooting Flowchart...................................................... 3-1

No Power .................................................................................... 3-2

No Video .................................................................................... 3-2

Memory Errors ........................................................................... 3-2

Losing the System's Setup Configuration ............................ 3-7

3-2 Technical Support Procedures ..................................................... 3-3

3-3 Frequently Asked Questions......................................................... 3-4

3-4 Returning Merchandise for Service.............................................. 3-7

Chapter 4: AMIBIOS

4-1 Introduction ...................................................................................... 4-1

4-2 BIOS Features ................................................................................. 4-2

BIOS Configuration Summary Screen ................................... 4-3

AMIBIOS Setup........................................................................... 4-3

SUPER P6DGH User's Manual

viii

Chapter 5: Running Setup

5-1 Setup................................................................................................. 5-1

Standard Setup ......................................................................... 5-1

Advanced Setup ........................................................................ 5-3

Chipset Setup............................................................................ 5-7

Power Management................................................................ 5-13

PCI/PnP Setup......................................................................... 5-15

Peripheral Setup ..................................................................... 5-18

5-2 Security Setup ............................................................................... 5-21

5-3 Utility Setup .................................................................................... 5-22

Anti-Virus .................................................................................. 5-22

Language................................................................................. 5-22

5-4 Default Settings............................................................................. 5-22

Optimal Default ....................................................................... 5-22

Fail-Safe Default ..................................................................... 5-22

Appendices:

Appendix A: BIOS Error Beep Codes and Messages........................ A-1

Appendix B: AMIBIOS Post Diagnostic Error Messages ................... B-1

Quick Reference Guide

Jumper Function Page

BZ_ON Buzzer Enable/Disable 2-18

JA5, JA6, JA7 SCSI Terminations 2-24

JB1, JB2, JB3, JB4 CPU Speed Selection 2-8

JBT1 CMOS Clear 2-17

JP11 External Bus Speed 2-8

JP20 ATX Power On/Off State 2-17

JP911 i960 Jumper 2-21

JP915 i960 Initialization Mode 2-21

JP917 i960 Jumper 2-21

JP918 i960 Reset Mode 2-21

JP919 i960 Retry Mode 2-21

JP920 i960 Disable Mode 2-21

JP921 i960 BIST Mode 2-21

JP924 i960 Jumper 2-21

Connector Function Page

AGP AGP Port 2-33

ID4 i960 Fail LED 2-20

J15, J16 IDE Interfaces 2-32

J17, J18 USB 2-15

J19 Parallel Port 2-30

J22 Floppy Connector 2-31

J36 (PWR_SEC) Secondary ATX Pwr Connector 2-11

J74 AT Keyboard 2-15

J940 I2C Connector 2-22

J943 i960 Serial Port 2-20

JF1 Hard Drive LED 2-14

JF1 Keylock/Power LED 2-13

JF1 Speaker 2-14

SUPER P6DGH User's Manual

JF2 IR Connector 2-12

JF2 ATX PW_ON 2-12

JF2 Reset Header 2-13

JL1 Chassis Intrusion 2-18

JOH1 Overheat LED 2-18

JP20, JP21 COM 1, COM 2 2-16

JP25 PS/2 Mouse Header 2-16

JT1, JT2 CPU1, CPU2 Fans 2-19

JT3 Thermal/Overheat Fan 2-19

PW1 Main AT Power Connector 2-10

PW2 Main ATX Power Connector 2-11

PW5 Secondary AT Pwr Connector 2-10

WOL Wake-On-LAN 2-19

Connector Function Page

Inhaltsverzeichnis

Andere Supermicro Hauptplatine Handbücher

Supermicro

Supermicro X11 UP Bedienungsanleitung

Supermicro

Supermicro P4DPR-iG2 Bedienungsanleitung

Supermicro

Supermicro X7DB8 Plus Bedienungsanleitung

Supermicro

Supermicro X9DRX PLUS-F Bedienungsanleitung

Supermicro

Supermicro SUPERO X10DRU-X Bedienungsanleitung

Supermicro

Supermicro C7B360-CB-M Bedienungsanleitung

Supermicro

Supermicro X11SCL-IF Bedienungsanleitung

Supermicro

Supermicro P3TDE6 Bedienungsanleitung

Supermicro

Supermicro Supero X6DAL-B2 Bedienungsanleitung

Supermicro

Supermicro X7DB8-X Bedienungsanleitung

Supermicro

Supermicro X11QPL Bedienungsanleitung

Supermicro

Supermicro X11SPL-F Bedienungsanleitung

Supermicro

Supermicro X11SCV-Q Bedienungsanleitung

Supermicro

Supermicro P3TDER Plus Bedienungsanleitung

Supermicro

Supermicro X11SSi-LN4F Bedienungsanleitung

Supermicro

Supermicro X11SSH-CTF Bedienungsanleitung

Supermicro

Supermicro X6DHR-8G2 Bedienungsanleitung

Supermicro

Supermicro X13DEG-OAD Bedienungsanleitung

Supermicro

Supermicro X5DAE Bedienungsanleitung

Supermicro

Supermicro Supero X8SAX Bedienungsanleitung

Supermicro

Supermicro SUPER P4SBA+ Bedienungsanleitung

Supermicro

Supermicro X13SEED-F Bedienungsanleitung

Supermicro

Supermicro X12SAE Bedienungsanleitung

Supermicro

Supermicro H12DGO-6 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung